Design of Metamaterial Based Efficient Wireless Power Transfer System Utilizing Antenna Topology for Wearable Devices

In this article, the design of an efficient wireless power transfer (WPT) system using antenna-based topology for the applications in wearable devices is presented. To implement the wearable WPT system, a simple circular patch antenna is initially designed on a flexible felt substrate by placing over a three-layer human tissue model to utilize as a receiving element. Meanwhile, a high gain circular patch antenna is also designed in the air environment to use as a transmitter for designing the wearable WPT link. The proposed WPT system is built to operate at the industrial, scientific and medical (ISM) band of 2.40–2.48 GHz. In addition, to improve the power transfer efficiency (PTE) of the system, a metamaterial (MTM) slab built with an array combination of 3 × 3 unit cells has been employed. Further, the performance analysis of the MTM integrated system is performed on the different portions of the human body like hand, head and torso model to present the versatile applicability of the system. Moreover, analysis of the specific absorption rate (SAR) has been performed in different wearable scenarios to show the effect on the human body under the standard recommended limits. Regarding the practical application issues, the performance stability analysis of the proposed system due to the misalignment and flexibility of the Rx antenna is executed. Finally, the prototypes are fabricated and experimental validation is performed on several realistic wearable platforms like three-layer pork tissue slab, human hand, head and body. The simulated and measured result confirms that by using the MTM slab, a significant amount of the PTE improvement is obtained from the proposed system.


Introduction
In the past few decades, a remarkable advancement in the biomedical field brings a radical change in the health monitoring and treatment of patients. Recently, wearable devices such as body sensors and smart electronic devices are widely used to observe the critical health conditions of patients [1][2][3]. These devices are used to construct a wireless body sensor network (WBSN), which enables constant monitoring and acquisition of physiological data like body temperature, blood pressure, glucose level and electrocardiogram (ECG), etc., of the patients and transfer these vital information's to the connected healthcare system [4]. However, attaining the practical and functional connectivity between the different sections of the body sensors remains a technical challenge. Usually, wires are broadly used to connect devices in clinical and research settings that disrupt physical activities and not suitable for continuous use. To power the wearable devices, a high demand exists for designing a simple, compact and efficient wireless power transfer (WPT) system that

Design of Wearable Wireless Power Transfer System
In this section, to construct the wearable WPT system, the design of the Tx and Rx antenna is presented. Furthermore, the configuration of the simulation setup to construct the WPT link by employing the designed Tx and Rx antenna has been illustrated.

Construction of the Wearable Receiving (Rx) and Transmitting (Tx) Antennas
In the case of wearable applications, simplicity and better performance are the prime concern for designing the WPT system. Keeping the requirement in mind, initially, we designed a simple inset-fed circular patch antenna over a flexible substrate with a full ground plane to use as an Rx element. The configuration of the Rx patch antenna is shown in Figure 1a. The antenna is constructed over the felt substrate having the permittivity of 1.63 and loss tangent of 0.044 with a thickness of 1 mm. The optimization of the Rx antenna is performed by placing it over the three-layer human tissue model, as shown in Figure 1b. The electrical property of different human tissue is mentioned in Table 1. The dimension of the wearable Rx antenna is adjusted to operate at the ISM of 2.45 GHz. The parameters of the wearable antenna are included in Table 2.
The measured and simulated result shows more than 9% efficiency enhancement due t the application of the MTM slab.

Design of Wearable Wireless Power Transfer System
In this section, to construct the wearable WPT system, the design of the Tx and R antenna is presented. Furthermore, the configuration of the simulation setup to constru the WPT link by employing the designed Tx and Rx antenna has been illustrated.

Construction of the Wearable Receiving (Rx) and Transmitting (Tx) Antennas
In the case of wearable applications, simplicity and better performance are the prim concern for designing the WPT system. Keeping the requirement in mind, initially, w designed a simple inset-fed circular patch antenna over a flexible substrate with a fu ground plane to use as an Rx element. The configuration of the Rx patch antenna is show in Figure 1a. The antenna is constructed over the felt substrate having the permittivity o 1.63 and loss tangent of 0.044 with a thickness of 1 mm. The optimization of the Rx antenn is performed by placing it over the three-layer human tissue model, as shown in Figur 1b. The electrical property of different human tissue is mentioned in Table 1. The dimen sion of the wearable Rx antenna is adjusted to operate at the ISM of 2.45 GHz. The param eters of the wearable antenna are included in Table 2.  In cases of wearable applications, either the Rx element is directly placed over th human body, or an air gap is considered between the body and antenna. Both states ar considered and studied during the design of wearable Rx antenna. The simulated retur  In cases of wearable applications, either the Rx element is directly placed over the human body, or an air gap is considered between the body and antenna. Both states are considered and studied during the design of wearable Rx antenna. The simulated return loss characteristics of the Rx antenna by placing over the body and considering an air gap (d) are shown in Figure 2. The measured result by placing the antenna on the three-layered pork slab is also included in Figure 2. A good agreement between the simulated and measured results has been observed. Furthermore, it can be seen from the return loss characteristics that the resonance frequency is retained at 2.45 GHz from simulations and at 2.46 GHz from the measurement. We also investigated the gain of the Rx patch antenna for the on-body and air gap scenario. However, for the sake of clarity, only the simulated and measured E-plane and H-plane radiation pattern of the Rx patch by directly placing on the human skin tissue model (in simulation) and on the pork slab (in measurement) is plotted in Figure 3. The maximum gain attained from the wearable Rx antenna is 1.86 dBi from the simulation, while 0.87 dBi from the measurement. Furthermore, the simulated radiation efficiency of the wearable antenna is 18.37 %, and the full width at half maxima (FWHM) is found to be 70.8 • /63.4 • in the E/H plane. Moreover, a detailed analysis of the wearable antenna characteristics for both on-body and an air gap (d) scenario is presented in Table 3. It can be seen from the tabulated data that although the resonance frequency of the antenna remains the same, but a slight change has been seen in the matching of return loss and gain of the antenna. Such stability obtained from the wearable antenna may be due to the presence of the full ground plane and the broadside directive radiation pattern of the patch. All the simulations are performed by utilizing the commercially available software ANSYS HFSS.
loss characteristics of the Rx antenna by placing over the body and considering an a (d) are shown in Figure 2. The measured result by placing the antenna on the three-la pork slab is also included in Figure 2. A good agreement between the simulated and ured results has been observed. Furthermore, it can be seen from the return loss c teristics that the resonance frequency is retained at 2.45 GHz from simulations and GHz from the measurement. We also investigated the gain of the Rx patch antenna on-body and air gap scenario. However, for the sake of clarity, only the simulate measured E-plane and H-plane radiation pattern of the Rx patch by directly plac the human skin tissue model (in simulation) and on the pork slab (in measurem plotted in Figure 3. The maximum gain attained from the wearable Rx antenna is 1. from the simulation, while 0.87 dBi from the measurement. Furthermore, the sim radiation efficiency of the wearable antenna is 18.37 %, and the full width at half m (FWHM) is found to be 70.8°/63.4° in the E/H plane. Moreover, a detailed analysis wearable antenna characteristics for both on-body and an air gap (d) scenario is pre in Table 3. It can be seen from the tabulated data that although the resonance freq of the antenna remains the same, but a slight change has been seen in the match return loss and gain of the antenna. Such stability obtained from the wearable an may be due to the presence of the full ground plane and the broadside directive rad pattern of the patch. All the simulations are performed by utilizing the comme available software ANSYS HFSS.   Table 3. It can be seen from the tabulated data that although the resonance frequ   To construct the WPT link, an inset-fed circular patch antenna with a full ground plane has also been designed to use as a Tx element in the air environment. The geometry of the Tx antenna is shown in Figure 4a. Herein, a patch antenna is utilized as a Tx element due to its simplicity, broadside radiation pattern and capability to integrate with the system easily. To obtain high gain from the Tx antenna, it is designed on a low-loss dielectric substrate having the dielectric permittivity of 2.2 and loss tangent 0.0009 with a thickness of 1.58 mm. The dimension of the Tx antenna is also optimized to operate at the same frequency (2.45 GHz) of the Rx element to obtain better performance from the designed system. The optimized parameter of the Tx antenna to operate at 2.45 GHz is given in Table 4. Furthermore, the simulated and measured return loss property of the Tx patch is shown in Figure 4b. The resonance frequency obtained from the measured result is 2.44 GHz for the antenna. Further, the simulated and measured radiation pattern characteristic is illustrated in Figure 5. The maximum gain achieved from the Tx antenna is 7.56 dBi from the simulation, while 7.13 dBi is achieved from the measurement. Moreover, the simulated radiation efficiency of the Tx antenna is 92.7%, and the FWHM is found to be 74.7 • /75.1 • in the E/H plane.   Table 4. Furthermore, the simulated and measured return loss property of the 159 shown in Figure 4b. The resonance frequency obtained from the measured r 160 GHz for the antenna. Further, the simulated and measured radiation pattern ch 161 is illustrated in Figure 5.

Design of Wearable WPT Link
The schematic configuration of the WPT system by integrating the designed Tx and Rx antennas from the previous section is presented in Figure 6a. The distance between the Tx antenna and the surface of Rx antenna is marked by d 1 . The transfer distance (d 1 ) has been chosen for the proposed system to operate in the radiative near-field region of the Tx antenna. In this region, the radiated beams are confined that provides better system performance with enhanced transmission distance and less sensitive to misalignments [19]. The variation of transmission characteristics (|S 21 |) with the increase of transmission distance (d 1 ) in the near-field region is presented in Figure 6b. It can be observed from the figure that the strength of |S 21 | is decreased with the increase of d 1 . This is due to the spreading nature of radiating waves and unwanted attenuation in the free space of the Tx antenna. It can also be seen from the figure that 60 mm distance provides the high value of |S 21 | (-8.54 dB), which offers better PTE. In the next section, a metamaterial slab is designed and utilized to concentrate or reduce the spreading nature of the radiating waves from the Tx antenna to improve the PTE of the system.

Metamaterial Integrated Proposed Wearable WPT System
The proposed wearable WPT systems integrated with an MTM slab containing an array of 3 × 3 both-sided ring unit cell is shown in Figure 7. The MTM is placed at a distance of d 2 from the wearable Rx antenna. The both-sided MTM ring unit cell configuration is used to improve the performance of the proposed WPT system is shown in Figure 8. In the figure, the orientation of the exciting electromagnetic wave to the MTM structure is also presented. The MTM structure is designed on an inexpensive FR4 dielectric substrate, having the permittivity of 4.4, loss tangent of 0.02 with a thickness of 1.6 mm. The dimensions of the MTM structure are optimized to obtain zero-index property at 2.45 GHz by following the methodology discussed in [25]. The optimized parameters of the ring structure are included in the caption of Figure 8. The transmission (|S 21 |) and reflection (|S 11 |) characteristic of the ring unit cell is shown in Figure 9a. The extracted effective refractive index property of the unit cell is also shown in Figure 9b. The parameter extraction is performed by the approach mentioned in [26]. It can be observed from Figure 9b that the ring unit cell provides the zero-index characteristic over the entire ISM (2.40-2.48 GHz) frequency band. Herein, the efficiency of the proposed system is improved by concentrating the radiating energy of the Tx antenna over the Rx antenna utilizing the zero-index behaviour of the MTM slab. As per Snell's law, when a spreading electromagnetic wave passes through a zero-index slab, the refracted wave becomes normal to the slab. Henceforth by utilizing the MTM slab, the gain of the Tx antenna is enhanced by focusing the incoming wave in the direction of broadside. Subsequently, the efficiency of the wearable WPT is enhanced significantly. The performance enhancement of the WPT system highly depends on the com tion of the unit cell array and its placement position (d2) from the receiving antenna [2 Henceforth, a parametric study has been performed to find out the optimal combin of unit cell array as well as its position, d2, that provides the better performance enh ment from the system. The simulated result for the various combinations of the un array is presented in Table 5. From the table, it can be seen that the combination of arrays offers a better increment (2.88 dB) in coupling strength (|∆S21|) that enhanc PTE of the system noticeably compared to other combinations. The optimal perform enhancement is obtained for the array combination of 3 × 3 due to the uniform illu tion effect of the MTM slab discussed in [27]. It can also be realized from Table 5 tha to increment in array combination, the performance of the system is degraded. T because a single Tx patch antenna cannot effectively illuminate the large panel size MTM slab, which generates a loss in the system [21,27]. Furthermore, the effect o MTM-slab (with 3 × 3 arrays) for the different placement positions (d2) in the prop WPT system is presented in Table 6. The optimization of d2 is performed to diminis near field coupling effect between the MTM slab and Tx patch. It can be perceived the table that at 8 mm distance, better enhancement in coupling strength (|∆S21|) tained. The improvement in coupling is attributed to better impedance matching a the MTM slab and the Tx patch at the specified distance [21,22,27].  The performance enhancement of the WPT system highly depends on the combination of the unit cell array and its placement position (d 2 ) from the receiving antenna [21,22]. Henceforth, a parametric study has been performed to find out the optimal combination of unit cell array as well as its position, d 2 , that provides the better performance enhancement from the system. The simulated result for the various combinations of the unit cell array is presented in Table 5. From the table, it can be seen that the combination of 3 × 3 arrays offers a better increment (2.88 dB) in coupling strength (|∆S 21 |) that enhances the PTE of the system noticeably compared to other combinations. The optimal performance enhancement is obtained for the array combination of 3 × 3 due to the uniform illumination effect of the MTM slab discussed in [27]. It can also be realized from Table 5 that due to increment in array combination, the performance of the system is degraded. This is because a single Tx patch antenna cannot effectively illuminate the large panel size of the MTM slab, which generates a loss in the system [21,27]. Furthermore, the effect of the MTM-slab (with 3 × 3 arrays) for the different placement positions (d 2 ) in the proposed WPT system is presented in Table 6. The optimization of d 2 is performed to diminish the near field coupling effect between the MTM slab and Tx patch. It can be perceived from the table that at 8 mm distance, better enhancement in coupling strength (|∆S 21 |) is attained. The improvement in coupling is attributed to better impedance matching among the MTM slab and the Tx patch at the specified distance [21,22,27]. Furthermore, to demonstrate the effect of the zero-index MTM slab on the transmission strength (|S 21 |) of the WPT system, a comparative study is performed with and without the integration of the MTM slab. The comparison of |S 21 |-characteristic is illustrated in Figure 10, with the variation of transfer distance (d 1 ). It can be clearly perceived from the figure that the transmission strength is enhanced significantly along with the change of transmission distance due to the use of MTM slab. Consequently, the efficiency of the proposed wearable system is enhanced considerably. Furthermore, to clarify the reason behind the performance improvement of the proposed MTM integrated WPT system, the Poynting vector distribution for without and with MTM integrated system is depicted in Figure 11a,b, respectively. From the figure, it can be seen that due to the integration of MTM slab, the radiated electromagnetic wave from the Tx antenna is concentrated over the wearable Rx antenna with higher intensity, which improves the performance of the system considerably.
ensors 2021, 21, x FOR PEER REVIEW Furthermore, to demonstrate the effect of the zero-index MTM slab sion strength (|S21|) of the WPT system, a comparative study is performe out the integration of the MTM slab. The comparison of |S21|-characteri in Figure 10, with the variation of transfer distance (d1). It can be clearly the figure that the transmission strength is enhanced significantly along of transmission distance due to the use of MTM slab. Consequently, the proposed wearable system is enhanced considerably. Furthermore, to c behind the performance improvement of the proposed MTM integrated Poynting vector distribution for without and with MTM integrated syste Figure 11a,b, respectively. From the figure, it can be seen that due to th MTM slab, the radiated electromagnetic wave from the Tx antenna is co the wearable Rx antenna with higher intensity, which improves the pe system considerably.  Moreover, a comparative performance analysis of the MTM integrated wearable WPT system is done by positioning the Rx antenna over the voxel models like human hand, head and torso. The simulation setup by placing the Rx antenna on the different portions of the human body is shown in Figure 12. This study is accomplished with the optimized 3 × 3 array combination of the unit cell on the MTM slab at d 1 = 60 mm and d 2 = 8 mm. Figure 13a,b depicts the S-parameter properties of the proposed wearable WPT system applied to different models. From Figure 13b, it can be observed that the strength of the transmission coefficient (|S 21 |) is enhanced significantly due to the use of MTM slab, which improves the efficiency of the system. For the sake of clarity, the S-parameter plots for the without MTM slab in case of the human hand, head and torso model are not incorporated in Figure 13. However, a detailed comparative study for the different wearable scenarios with and without the integration of the MTM slab is furnished in Table 7. Herein, the efficiency of the WPT is calculated from the transmission characteristics (|S 21 |) as, η = |S 21 | 2 [20][21][22]. A change in efficiency improvement, along with a shift in operating frequency, is observed from Table 7. Such variation occurs as the human body is a most complex environment with the discrepant dielectric properties of various parts of human tissues [28], which usually affects the system's performance differently. In the proposed wearable WPT system, the performance is analyzed for a homogeneous three-layer tissue model as well as for inhomogeneous and irregular structures such as the human hand, head and torso model. Even though the excitation power is kept the same for the Tx antenna, but the dielectric property, size and geometry of the different wearable scenarios vary simultaneously. Henceforth, a variation in the transmission efficiency improvements and shift in operating frequency is observed in Table 7. From the comparative study for the different wearable scenarios, it is clear that the proposed WPT system may be considered for application in the various wearable applications. Furthermore, to demonstrate the effect of the zero-index MTM slab on the transmis sion strength (|S21|) of the WPT system, a comparative study is performed with and with out the integration of the MTM slab. The comparison of |S21|-characteristic is illustrated in Figure 10, with the variation of transfer distance (d1). It can be clearly perceived from the figure that the transmission strength is enhanced significantly along with the change of transmission distance due to the use of MTM slab. Consequently, the efficiency of the proposed wearable system is enhanced considerably. Furthermore, to clarify the reason behind the performance improvement of the proposed MTM integrated WPT system, the Poynting vector distribution for without and with MTM integrated system is depicted in Figure 11a,b, respectively. From the figure, it can be seen that due to the integration o MTM slab, the radiated electromagnetic wave from the Tx antenna is concentrated ove the wearable Rx antenna with higher intensity, which improves the performance of the system considerably. Moreover, a comparative performance analysis of the MTM integrated wearable WPT system is done by positioning the Rx antenna over the voxel models like human hand, head and torso. The simulation setup by placing the Rx antenna on the differen portions of the human body is shown in Figure 12. This study is accomplished with the optimized 3 × 3 array combination of the unit cell on the MTM slab at d1 = 60 mm and d2 = 8 mm. Figure 13a,b depicts the S-parameter properties of the proposed wearable WPT system applied to different models. From Figure13b, it can be observed that the strength of the transmission coefficient (|S21|) is enhanced significantly due to the use of MTM slab

Misalignment and Bending Analysis of the Proposed MTM Integrated System
In the application scenario, it is necessary to estimate the performance stability of the proposed WPT system due to the movement of the human body. Hence, the stability of the system performance is investigated in light of the misalignment between the Tx and Rx antenna. Furthermore, the flexibility effect of the wearable Rx antenna on the system performance is studied.

Misalignment Analysis
Perfect alignment among the Tx and Rx antenna is difficult due to the movement of the human posture. Henceforth, the lateral and angular misalignment analysis of the Tx antenna is performed to show the effect on the performance of the proposed WPT system. The analysis of the lateral misalignment is performed by moving the Tx antenna parallelly by keeping the MTM-slab and Rx antenna fixed at their positions, as shown in Figure 14a. In the figure, the lateral offset distance of the Tx antenna is specified by 'L a '. A comparative study about the coupling strengths (|S 21 |) between the Tx and Rx antenna with the variation of L a is presented in Figure 14b. Furthermore, in Table 8, the effect of lateral alignment on the operating frequency and transmission strength is clearly presented. It can be perceived from the table that with the enhancement of the 'L a ', the transmission strength of the system is degraded along with a frequency shift.  Furthermore, the study of angular misalignment is also executed by rotating t antenna in the yz-plane by keeping the MTM-slab and Rx antenna fixed at their posi as represented in Figure 15a. The change in transmission strength (|S21|) is also st for the different values of rotation angle (θr) and presented in Figure 15b. Moreover better understanding about the effect of angular misalignment, a comparative stu given in Table 9. A slight change in the coupling strengths (|S21|) can be observed the table.  Furthermore, the study of angular misalignment is also executed by rotating the Tx antenna in the yz-plane by keeping the MTM-slab and Rx antenna fixed at their positions, as represented in Figure 15a. The change in transmission strength (|S 21 |) is also studied for the different values of rotation angle (θ r ) and presented in Figure 15b. Moreover, for a better understanding about the effect of angular misalignment, a comparative study is given in Table 9. A slight change in the coupling strengths (|S 21 |) can be observed from the table.
antenna in the yz-plane by keeping the MTM-slab and Rx antenna fixed at their positio as represented in Figure 15a. The change in transmission strength (|S21|) is also stud for the different values of rotation angle (θr) and presented in Figure 15b. Moreover, f better understanding about the effect of angular misalignment, a comparative stud given in Table 9. A slight change in the coupling strengths (|S21|) can be observed fr the table.

Bending Analysis
The wearable Rx antenna has been designed over a flexible felt substrate to eliminate the difficulty faced with the rigid substrate during the integration on the human body. To analyze the flexibility effect, the Rx antenna has been wrapped around the three-layer cylindrical tissue model of radius R, illustrated in Figure 16a

Bending Analysis
The wearable Rx antenna has been designed over a flexible felt substrate to eliminate the difficulty faced with the rigid substrate during the integration on the human body. To analyze the flexibility effect, the Rx antenna has been wrapped around the three-layer cylindrical tissue model of radius R, illustrated in Figure 16a

Analysis of Specific Absorption Rate (SAR)
The safety of the human body and health is the prime concern against the harmful effects of the electromagnetic (EM) field for human exposure. Therefore, the major challenge regarding the design of an efficient WPT system, particularly for the wearable WPT

Analysis of Specific Absorption Rate (SAR)
The safety of the human body and health is the prime concern against the harmful effects of the electromagnetic (EM) field for human exposure. Therefore, the major challenge regarding the design of an efficient WPT system, particularly for the wearable WPT system, is to maintain the safety standards. Regarding safety, the value of SAR would be taken into consideration for the transmission of high power at enhanced transmission distances. Generally, the SAR is defined by the rate of absorbed energy within the unit mass of the human body when explored in the EM field. The SAR value is also expressed mathematically by using the following equation [29], where σ is the tissue conductivity (S/m), E is the electric field density (V/m), and ρ is the intensity of tissue (kg/m 3 ). It can be realized from the above expression that the SAR value depends upon the property of human tissue and its density along with the induced E-field from the Tx element. Furthermore, the level of EM radiation absorbed by the human body is directly related to the conductivity of the human organs. Usually, the tissue of human body consists with a lot of water that increases the conductivity. Henceforth, the SAR varies on the different body parts of the human [30].
In the present study, the 1-g average SAR distribution for the proposed MTM integrated WPT system for the different wearable scenarios is illustrated in Figure 17. From the figure, the obtained peak SAR value in the case of the three-layer tissue, hand, head and torso model are 14.26, 12.41, 8.50 and 2.08 W/kg, respectively. However, regarding the safety of the human body, the maximum average SAR value over the 1-g of cubic tissue model allowed by the IEEE C95.1−1999 standard should be less than or equal to 1.6 W/kg [31]. As per the recommendation of the Federal Communications Commission's (FCC) standards [32], the maximum allowed transmitter output energy fed to the Rx antenna at the ISM-bands is at 1 W (30 dBm). Herein, the distribution of the SAR is performed for the maximum 1 W excitation power set at the Tx patch. Moreover, by decreasing the excitation power at the transmitter end, the peak 1-g average SAR value should be kept within the standard limit [20][21][22]. The excitation power required at the Tx end to keep the SAR value in safety limits in the case of the three-layer tissue, hand, head and torso model are 0.11, 0.13, 0.19 and 0.78 W, respectively. Furthermore, the novel property of metamaterial has also been utilized to reduce the SAR [33][34][35][36] without reducing the excitation power at the Tx end. In [33], an MTM structure consists of split-ring resonators (SRRs) has been used to reduce the electromagnetic interface between the antenna and the human head. Furthermore, an MTM-based perfect artificial magnetic conductor (AMC) has been used to minimize the SAR of a planar inverted-F antenna [34]. Further, the performance enhancement and SAR reduction of a dual-band flexible antenna have been achieved in [35] by using an MTM-slab at the backside of antenna in WBAN application. In [36], an MTM reflector was recently designed on a felt textile substrate to reduce the SAR effect and increase the performance of an ultrawideband antenna for WBAN applications. Moreover, the SAR value of the proposed MTM based wearable WPT system might also be reduced by the approach presented in Refs. [33][34][35][36].

Measurement and Discussion
To validate the proposed design concept of the wearable WPT system, the different parts such as Tx, Rx antenna, and the array of 3 × 3 MTM slab have been fabricated. The standard printed circuit board (PCB) technology has been used to design the Tx antenna and MTM slab. The wearable Rx antenna is designed over a felt substrate using an adhesive copper sheet with a thickness of 0.035 mm. To sustain the conductivity of uniform surface, a single copper sheet has been utilized to construct both the full ground and radiating patch along with microstrip feed without any discontinuity or interconnects. The photographs of the fabricated prototype to build the wearable WPT link are shown in Figure 18. The three-layer pork tissue has been used to consider the realistic multi-layered environment for measurement purpose [23]. Furthermore, the measurements are conducted by placing the wearable antenna over the human hand, head and body (chest). The pictures of measurements regarding the realistic scenario of the wearable platforms like the threelayered pork slab and also at the different portions of the human body integrated with the MTM slab are presented in Figure 19. The MTM slab has been attached over the wearable Rx patch antenna by using Styrofoam. The measurements are performed with the help of the Anritsu S820E vector network analyzer.
nsors 2021, 21, x FOR PEER REVIEW environment for measurement purpose [23]. Furthermore, the measu ducted by placing the wearable antenna over the human hand, head and pictures of measurements regarding the realistic scenario of the wearab the three-layered pork slab and also at the different portions of the human with the MTM slab are presented in Figure 19. The MTM slab has been wearable Rx patch antenna by using Styrofoam. The measurements are the help of the Anritsu S820E vector network analyzer.    During measurement, the distance (d1) between Tx and Rx an mm, whereas the MTM slab is placed at a distance (d2) of 8 mm antenna, as shown in Figure 19. The Tx, Rx antenna and MTM slab on the same horizontal line during the experiment to obtain better system. A comparative study between the measured efficiency in for without (W/O) and with the integration of MTM slab is shown i found from the figure that for the use of MTM slab, the efficiency o is improved significantly. Herein, the efficiency has been calculate transmission (|S21|) coefficient characteristics. Furthermore, the d obtained measured results from the different wearable scenarios During measurement, the distance (d 1 ) between Tx and Rx antenna is considered 60 mm, whereas the MTM slab is placed at a distance (d 2 ) of 8 mm from the wearable Rx antenna, as shown in Figure 19. The Tx, Rx antenna and MTM slab are aligned properly on the same horizontal line during the experiment to obtain better performance from the system. A comparative study between the measured efficiency in the different scenarios for without (W/O) and with the integration of MTM slab is shown in Figure 20a. It can be found from the figure that for the use of MTM slab, the efficiency of the proposed system is improved significantly. Herein, the efficiency has been calculated from the measured transmission (|S 21 |) coefficient characteristics. Furthermore, the detailed analysis of the obtained measured results from the different wearable scenarios with and without the integration of the MTM slab is summarized in Table 10. From the table, it can be observed that the measured coupling strength |S 21 | is improved significantly with the presence of MTM slab, which enhances the efficiency of the system. The improvements in the measured efficiencies are 9.62%, 9.61%, 10.6% and 8.2% in the case of three-layer pork slab, human hand, head and body (chest), respectively. Furthermore, to present the MTM effect on the PTE of the system, transfer distance (d 1 ) is increased, keeping the value of d 2 fixed at 8 mm in the measurement scenario of the three-layer pork slab. The simulated and measured efficiency plot of the WPT system for the three-layer phantom model and pork slab environment is also presented in Figure 20b. From the figure, it can be observed that by using the ZIM slab, the efficiency level of the proposed WPT system is improved significantly, even with the increase in transmission distance. However, some extent of mismatch is seen between the measured and simulated results, which occurred due to the fabrication tolerance as well as misalignment during measurement.
integration of the MTM slab is summarized in Table 10. From the table, it can be ob that the measured coupling strength |S21| is improved significantly with the pres MTM slab, which enhances the efficiency of the system. The improvements in the ured efficiencies are 9.62%, 9.61%, 10.6% and 8.2% in the case of three-layer por human hand, head and body (chest), respectively.  Furthermore, to present the MTM effect on the PTE of the system, transfer d (d1) is increased, keeping the value of d2 fixed at 8 mm in the measurement scenario three-layer pork slab. The simulated and measured efficiency plot of the WPT sys the three-layer phantom model and pork slab environment is also presented in Figu From the figure, it can be observed that by using the ZIM slab, the efficiency leve proposed WPT system is improved significantly, even with the increase in transm distance. However, some extent of mismatch is seen between the measured and sim results, which occurred due to the fabrication tolerance as well as misalignment measurement.
Finally, a comparative study has been furnished in Table 11 with the propose  Finally, a comparative study has been furnished in Table 11 with the proposed work and works reported in the literature. From the table, it can be perceived that the reported work in the literature usually employs the non-radiative inductive or resonant couplingbased approach to design the wearable WPT system, whereas, in the present study, antenna topology has been adopted. The proposed system has been constructed on a compact, flexible substrate using a simple design configuration. The system is also applicable for different wearable scenarios such as the human hand, head and body.