Study on the Effectiveness of Simultaneous Recovery and Concentration of 1-Ethyl-3-methylimidazolium Chloride Ionic Liquid by Electrodialysis with Heterogeneous Ion-Exchange Membranes

Due to the extensive range of ionic liquids (ILs) used in industry, an efficient recovery method is needed. In this study, the effectiveness of a simultaneous concentration and recovery method was investigated for 1-ethyl-3-methylimidazolium chloride ([Emim]Cl), an IL that was recovered using electrodialysis (ED). The optimal operational parameters for electrodialytic recovery were determined empirically. The variables that were investigated included the concentration of IL, applied voltage, linear flow velocity and the diluate-to-concentrate volume ratio. The recovery of [Emim]Cl, the concentration degree, the [Emim]Cl flux across membranes, the current efficiency, as well as the energy consumption were determined. The results of the experiments confirmed that [Emim]Cl concentration and recovery can be achieved using ED. The highest ED efficiency was obtained when a 2 V electric potential per one membrane pair was applied, using a 2 cm/s linear flow velocity, and by adjusting to 0.2 M IL in the feed solution. By using ED, a 2.35-fold concentration of [Emim]Cl with a recovery of 90.4% could be achieved when the diluate-to-concentrate volume ratio was 2. On the other hand, a 3.35-fold concentration of [Emim]Cl with a recovery of 81.7% could be obtained when the diluate-to-concentrate volume ratio was increased to 5.


Introduction
An ionic liquid (IL) is a liquid salt. The melting points of ILs are generally below room temperature, occasionally below 0 • C, and they are classified as molten salts [1,2]. ILs are characterized, for example, by high thermal and chemical stability, negligible vapor pressure, non-flammability and a wide electrochemical window. However, it should be noted that ILs may be toxic [3,4]. Due to their unique chemical and physical properties, they can be used in fields such as in wastewater treatment, electrochemistry, catalysis, analysis and biomass valorization [5]. ILs are also classified on the basis of their properties and their applications, such as task-specific ILs, supported ILs, chiral ILs, protic ILs, bio ILs, polarizable ILs, metal salt ILs, switchable-polarity solvents and deep eutectic solvents [6,7]. ILs are regarded as green solvents because of their recyclability and the potential to replace volatile organic solvents [8][9][10].
ILs are often used for the treatment of environmental samples, such as for the treatment of lignocellulosic biomass. Imidazolium ILs can liquefy lignin, cellulose and therefore wood. A reagent that is commonly used as a solvent for the liquefaction of wood is 1-ethyl-3-methylimidazolium chloride ([Emim]Cl).
[Emim]Cl allows lignin and polysaccharides to be liquefied at temperatures around 100 • C. Thus, [Emim]Cl can be used as an alternative

Experimental Solutions
The experiments were conducted using the configuration defined in Section 2.2, with a solution containing aqueous [Emim]Cl (Sigma Aldrich, Saint Louis, MO, USA). A sulfuric acid solution with a conductivity of 20 mS/cm was used as the electrode rinse solution. The solution compositions are presented in Table 1. Deionized water was prepared using a Millipore Elix 10 system.

ED Stack, Membranes and ED Method
The ED experiments were carried out using an EDR-Z/10-0.8 module (MemBrain, Straz pod Ralskiem, Czech Republic) with an effective single-membrane area of 64 cm 2 . There were ten pairs of membranes in the ED stack. The ion-exchange membranes (IEMs) used in this investigation were heterogeneous AM(H)-CM(H) (Ralex, Straz pod Ralskiem, Czech Republic). The morphology of the tested heterogeneous ion-exchange membranes is shown in Figure 1. We proved that these membranes had a heterogeneous morphology, with the ion-exchange resin heterogeneously incorporated into the polymer membrane matrix. The anode and cathode in the electrodialyzer were made of platinized titanium. A scheme of the ED stack is shown in Figure 2. Before the ED experiments, the surface morphology of the tested membranes was investigated using a scanning electron microscope (Hitachi TM3000 table-top TM series,  Tokio, Japan), equipped with a backscattered electron (BSE) detector.   The ED module consisted of the diluate, concentrate and electrode compartments. All ED experiments were conducted periodically with process solution recirculation. Process solutions such as the diluate, concentrate and electrode-rinse solution were recirculated by a peristaltic pump (Masterflex L/S, Cole-Parmer, Vernon Hills, IL, USA). The solution volumes were 200 mL for the diluate, 100 mL for the concentrate and 200 mL for the electrode rinse solution. The ED tests were conducted at constant voltage, which was a maximum value determined using the limiting current density test. The effects of the initial [Emim]Cl concentration (0.05 to 0.25 mol/L), different applied voltages (10, 15 and 20 V), different linear flow velocities (1 to 3 cm/s) and the diluate-to-concentrate volume ratio (2, 3, 4 and 5) were investigated. The experiments were performed until the diluate conductivity dropped to 0.25 mS/cm, which was monitored using a CPC-461 pH/conductivity meter (Elmetron, Zabrze, Poland). During the experiments, the electric current as well as the conductivities of the diluate and concentrate were measured every minute. The experiments were performed at 25 • C. For all of the ED experiments, three independent replicates were conducted, and the standard deviations were calculated.
Before the ED experiments, the surface morphology of the tested membranes was investigated using a scanning electron microscope (Hitachi TM3000 table-top TM series,  Tokyo, Japan), equipped with a backscattered electron (BSE) detector.

Limiting Current Density (LCD)
The LCDs were determined based on current-voltage curves using the Cowan-Brown method [28], for solutions with [Emim]Cl concentrations of 0.05, 0.10, 0.15, 0.20 and 0.25 mol/L. The applied voltage was increased stepwise at a rate of 0.5 V/min until the ED cell potential drop reached 25 V.

Analytical Methods
The concentrations of the [Emim]Cl solutions were determined with a UV-VIS spectrophotometer (Varian Cary 50 Scan, Agilent, Santa Clara, CA, USA). The UV-VIS absorption spectra of [Emim] + were measured in a 10 mm quartz cuvette. The spectrophotometer utilizes a dual-beam optical system, which can achieve spectral scanning over a wide wavelength range of 190 to 1100 nm. The UV-VIS spectra were pre-processed by baseline correction using deionized water as the reference. The maximum absorption wavelength for the [

ED Effectiveness Determination
On the basis of the obtained results, the [Emim]Cl recovery ratio (

ED Effectiveness Determination
On the basis of the obtained results, the [Emim]Cl recovery ratio (

ED Effectiveness Determination
On the basis of the obtained results, the [Emim]Cl recovery ratio (R [Emim]Cl ), the [Emim]Cl concentration degree (R conc ), the electric current efficiency (CE [Emim]Cl ) and the energy consumption (EC) were calculated as follows: where m dil IL,0 is the initial mass (g) of the IL in the diluate solution before ED and m conc IL,t is the increase in the IL mass (g) in the concentrate solution after ED.

•
The [Emim]Cl concentration degree (R conc ) where C dil IL,0 is the initial concentration (mol/L) of the IL in the diluate solution before ED and C conc IL,t is the final concentration (mol/L) of the IL in the concentrate solution after ED.

•
The electric current efficiency (CE [Emim]Cl ) where F is the Faraday constant (96,485 C·mol −1 ), z is the charge number of [Emim] + , V conc,t is the volume of the concentrate solution after ED (L), C conc IL,t is the concentration of the IL in the concentrate solution after ED (g·L −1 ), M IL is the molar mass of [Emim]Cl (g·mol −1 ), n is the number of membrane pairs and I is the electric current (A).

•
Energy consumption (EC) where EC is the energy consumption, U is the applied voltage (V), I is the electric current in (A) and V dil,0 is the initial diluate volume (L).

Results and Discussion
The objective of the present study was to investigate the effectiveness of the [Emim]Cl recovery and concentration by following an optimized ED protocol. The effects of the initial [Emim]Cl concentration (0.05-0.25 mol/L), applied voltage (10-20 V), linear flow velocity (1-3 cm/s) and the diluate-to-concentrate volume ratio (2, 3, 4 and 5) are described in the following sections.

LCDs Determination
In this study, firstly, the LCDs were determined. The LCDs of the [Emim]Cl solutions were determined using the relationship between the cell resistance and the reciprocal of the current (Cowan-Brown method [28]). As suspected, the LCD depended upon the [Emim]Cl concentration in the diluate solution. The obtained results are presented in Figure 5. We found that the LCD increased linearly with increasing

Effect of the Initial [Emim]Cl Concentration
The effect of the initial [Emim]Cl concentration on the effectiveness of the IL recovery and concentration was evaluated by testing five different starting concentrations of [Emim]Cl. The experimental conditions are presented in Table 1. The experiments were conducted in constant-voltage mode, but below the determined LCD, as previously mentioned. The initial diluate-to-concentrate volume ratio equaled 2.
The effect of the initial [Emim]Cl concentration on the performance of ED is presented in Figures 6-8 flux did not change. However, within the margin of 0.05-0.2 M, it was also found that the initial IL concentration did not greatly influence the recovered IL concentration.
In all cases, the [Emim]Cl concentration degree was slightly higher than 2.2 ( Figure  7). Moreover, as shown in Figure 8, the electric current efficiency did not depend strongly on the initial IL concentration. The electric current efficiency was in the range of 39-48%. The concentration of IL also impacted the membrane stack energy consumption. Figure 8 shows that with an increase in the initial IL concentration in the diluate, the energy consumption increased.

Effect of the Initial [Emim]Cl Concentration
The effect of the initial [Emim]Cl concentration on the effectiveness of the IL recovery and concentration was evaluated by testing five different starting concentrations of [Emim]Cl. The experimental conditions are presented in Table 1. The experiments were conducted in constant-voltage mode, but below the determined LCD, as previously mentioned. The initial diluate-to-concentrate volume ratio equaled 2.
The effect of the initial [Emim]Cl concentration on the performance of ED is presented in Figures 6-8. We observed that the concentration of [Emim]Cl influenced the [Emim] + flux across the cation-exchange membranes and the IL recovery (Figures 6 and 7

Effect of the Applied Voltage
The effect of the applied voltage on [Emim]Cl recovery and concentration effectiveness was evaluated by three separate ED experiments, which used a 0.  In all cases, the [Emim]Cl concentration degree was slightly higher than 2.2 ( Figure 7). Moreover, as shown in Figure 8, the electric current efficiency did not depend strongly on the initial IL concentration. The electric current efficiency was in the range of 39-48%. The concentration of IL also impacted the membrane stack energy consumption. Figure 8 shows that with an increase in the initial IL concentration in the diluate, the energy consumption increased. lution with a linear flow velocity equal to 2 cm/s. The examined voltages were 10 V, 15 V and 20 V. The experiments were conducted until the diluate's conductivity was lower than 0.25 mS/cm. The ED effectiveness was evaluated according to the IL recovery ratio, the [Emim]Cl concentration degree, the [Emim] + molar flux, the CE and the EC. The results are presented in Figures 9 and 10.

Effect of the Applied Voltage
We found that the applied voltage influenced the [Emim]Cl recovery and the [Emim] + molar flux across cation-exchange membranes. The [Emim]Cl recovery and the [Emim] + molar flux increased with an increase in the applied voltage, to maximum values of 90.42% and 2.66 mol/m 2 ·h, respectively, as shown in Figure 9.    Figure 10). However, when the voltage increased from 15 V to 20 V, the current efficiency slightly increased to 42.9%. As shown in Figure 10, the energy consumption increased with increasing applied voltage.

Effect of the Linear Flow Velocity
One of the important parameters which influences ED efficiency is fluid dynamics. In this section, the effect of the linear flow velocity on the effectiveness of [Emim]Cl con-  Figure 9. Figure 9 shows that the [Emim]Cl concentration degree also depended on the applied voltage during ED. The [Emim]Cl concentration degree increased slightly with an increase in the applied voltage. The maximum value of the [Emim]Cl concentration degree was 2.35 for 15 V. Moreover, while the applied voltage increased from 10 V to 15 V, the current efficiency slightly decreased to values near 38% ( Figure 10). However, when the voltage increased from 15 V to 20 V, the current efficiency slightly increased to 42.9%. As shown in Figure 10, the energy consumption increased with increasing applied voltage.

Effect of the Linear Flow Velocity
One of the important parameters which influences ED efficiency is fluid dynamics. In this section, the effect of the linear flow velocity on the effectiveness of [Emim]Cl concentration and recovery was evaluated by three simultaneous ED experiments conducted using the same

Effect of the Diluate-to-Concentrate Volume Ratio
The IL concentration degree depends on the initial diluate volume. When the diluateto-concentrate volume ratio is high, the concentration degree should be greater in comparison with a low ratio. However, the trade-off in having a high concentration degree is that the concentration difference between the diluate and concentrate during ED is higher [1,29]. This promotes electro-osmotic water transport and the concentration gradient between the diluate and concentrate. Figure 13 shows that, as suspected, the [Emim]Cl concentration degree increased with increasing initial diluate volume. When the diluate-toconcentrate volume ratio was 5, the concentration degree increased to a maximum value of 3.35 (in the examined range). Additionally, the energy consumption increased with the

Effect of the Diluate-to-Concentrate Volume Ratio
The IL concentration degree depends on the initial diluate volume. When the diluateto-concentrate volume ratio is high, the concentration degree should be greater in comparison with a low ratio. However, the trade-off in having a high concentration degree is that the concentration difference between the diluate and concentrate during ED is higher [1,29]. This promotes electro-osmotic water transport and the concentration gradient between the diluate and concentrate. Figure 13 shows that, as suspected, the [Emim]Cl concentration degree increased with increasing initial diluate volume. When the diluate-to-concentrate volume ratio was 5, the concentration degree increased to a maximum value of 3.35 (in the examined range). Additionally, the energy consumption increased with the increase in the initial diluate volume ( Figure 14). However, while the initial diluate volume increased, the concentration gradient between diluate and concentrate increased, and the [Emim] + molar flux across cation-exchange membranes dramatically decreased ( Figure 13). Thus, it was noted that when the diluate-to-concentrate volume ratio increased from 2 to 5, the [Emim]Cl recovery and current efficiency decreased from 90.4% to 81.7%, and from 42.9% to 38.8%, respectively (Figures 13 and 14). increase in the initial diluate volume ( Figure 14). However, while the initial diluate volume increased, the concentration gradient between diluate and concentrate increased, and the [Emim] + molar flux across cation-exchange membranes dramatically decreased (Figure 13). Thus, it was noted that when the diluate-to-concentrate volume ratio increased from 2 to 5, the [Emim]Cl recovery and current efficiency decreased from 90.4% to 81.7%, and from 42.9% to 38.8%, respectively (Figures 13 and 14).

Comparison of ILs Recovery Performance Using the ED Method
Because ILs are gaining important roles in various industrial fields, their recovery is also becoming important. Table 2 presents a comparison of the recovery effectiveness of commonly used ILs using the ED method.  [14] was lower compared to the ILs recovery obtained for 0.2 M [Emim]Cl, which has a smaller ionic radius. The ILs content in the diluate also influenced the ILs transport rate. The ILs transport rate increased with increasing IL concentration in the initial diluate solution. The current efficiency also highly depended on ED performance. The applied voltage also influenced ED performance. When the voltage increased, the current efficiency slightly increased [15]. Table 2 shows that IL recovery above 90% can be also obtained by the application of electrodialysis with a bipolar membrane (BMED) [25,27]. BMED is a method for the generation of H + and OHions, which can be used to produce bases and acids from salts [30]. The results presented in Table 2 indicate that it is very important to select the optimal ED process operating parameters.

Conclusions
The various industries that use ILs generate a wide range of wastewaters containing dilute ILs. Because this type of waste could have a negative effect on the environment and human health by polluting the water, air and soil, the recovery of ILs constitutes a very important initiative.
In the current study, the possibility of simultaneous [Emim]Cl recovery and concentration from aqueous solutions by ED was investigated. It was observed that [Emim]Cl was removed from the diluate effectively using the proposed method. The obtained results proved that a recovery of up to 90.4% is possible. It was also proven that the ED process could be optimized to allow for concentration of the IL. In fact, the [Emim]Cl content in the examined process increased by 2.55 times in comparison to the IL concentration in the initial diluate compartment. At a diluate-to-concentrate volume ratio of 5, a 3.35-fold concentration of [Emim]Cl, with a recovery of 81.7%, could be obtained. It was shown that the IL concentration, applied voltage drop, linear flow velocity and diluate-to-concentrate volume ratio all had an influence on the recovery efficiency and concentration of the chosen IL. The highest ED efficiency for the recovery and concentration of [Emim]Cl was obtained at 20 V applied potential, 2 cm/s linear flow velocity and 0.2 M IL in the feed solution.
The performed experiments allowed the operating parameters of [Emim]Cl recovery by ED to be optimized; therefore, the obtained results could be a valuable base to develop and scale-up the method for the recovery and concentration of [Emim]Cl from industrial wastewater. In future, the ED methodology presented here could be a good way to recycle ILs and be a highly valuable wastewater utilization method, especially for wastewater originating from biomass utilization processes or the pharmaceutical industry.

Institutional Review Board Statement: Not applicable.
Informed Consent Statement: Not applicable.

Data Availability Statement:
The data presented in this study are available on request from the corresponding author.