Biosurfactants: Multifunctional Biomolecules of the 21st Century

In the era of global industrialisation, the exploration of natural resources has served as a source of experimentation for science and advanced technologies, giving rise to the manufacturing of products with high aggregate value in the world market, such as biosurfactants. Biosurfactants are amphiphilic microbial molecules with hydrophilic and hydrophobic moieties that partition at liquid/liquid, liquid/gas or liquid/solid interfaces. Such characteristics allow these biomolecules to play a key role in emulsification, foam formation, detergency and dispersal, which are desirable qualities in different industries. Biosurfactant production is considered one of the key technologies for development in the 21st century. Besides exerting a strong positive impact on the main global problems, biosurfactant production has considerable importance to the implantation of sustainable industrial processes, such as the use of renewable resources and “green” products. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of bioremediation as well as the petroleum, food processing, health, chemical, agricultural and cosmetic industries. In this paper, we offer an extensive review regarding knowledge accumulated over the years and advances achieved in the incorporation of biomolecules in different industries.


ent degrees o
polarity and hydrogen bridges, such as oil/water or air/water interfaces.The apolar moiety is often a hydrocarbon chain, whereas the polar moiety may be ionic (cationic or anionic), non-ionic or amphoteric [1,2], as illustrated in Figure 1.Surfactants increase the solubility of hydrophilic molecules, thereby reducing both surface and interfacial tensions at the oil/water interface [3].The critical micelle concentration (CMC) is the concentration of surfactant at which organised molecular assemblies, known as micelles, are formed (Figure 2) and corresponds to the point at which the tensioactive agent achieves the lowest stable surface tension (Figure 3) [4].

Most currently produced surfactants are chemically derived from petroleum.However, such synthetic tensioactive agents are generally toxic and difficult to break down thr ugh the action of microorganisms.In recent years, such problems have motivated the scientific community to seek surfactants that are more environmentally friendly, such as those achieved through microbial production, known as biosurfactants [5].Moreover, concerns regarding the environment on the part of consumers and new environmental control legislation have led to the development of natural surfactants as an alternative to existing products.Surfactants increase the solubility of hydrophilic molecules, thereby reducing both surface and interfacial tensions at the oil/water interface [3].The critical micelle concentration (CMC) is the concentration of surfactant at which organised molecular assemblies, known as micelles, are formed (Figure 2) and corresponds to the point at which the tensioactive agent achieves the lowest stable surface tension (Figure 3) [4].Surfactants increase the solubility of hydrophilic molecules, thereby reducing both surface and interfacial tensions at the oil/water interface [3].The critical micelle concentration (CMC) is the concentration of surfactant at which organised molecular assemblies, known as micelles, are formed (Figure 2) and corresponds to the point at which the tensioactive agent achieves the lowest stable surface tension (Figure 3) [4].

Most currently produced surfactants are chemically derived from petroleum.However, such synthetic tensioactive agents are generally toxic and difficult to break down through the ac ion of microorganisms.In recent years, such problems have motivated the scientific community to seek surfactants that are more environmentally friendly, such as those achieved through microbial production, known as biosurfactants [5].Moreover, concerns regarding the environment on the part of consumers and new environmental control legislation have led to the development of natural surfactants as an alternative to existing products.Surfactants increase the solubility of hydrophilic molecules, thereby reducing both surface and interfacial tensions at the oil/water interface [3].The critical micelle concentration (CMC) is the concentration of surfactant at which organised molecular assemblies, known as micelles, are formed (Figure 2) and corresponds to the point at which the tensioactive agent achieves the lowest stable surface tension (Figure 3) [4].

Most currently produced surfactants are chemically derived from petroleum.However, such synthetic tensioactive agents are generally toxic and difficult to break down through the action of m croorganisms.In recent years, such problems have motivated the scientific community to seek surfactants that are more environmentally friendly, such as those achieved through microbial production, known as biosurfactants [5].Moreover, concerns regarding the environment on the part of consumers and new environmental control legislation have led to the development of natural surfactants as an alternative to existing products.Most currently produced surfactants are chemically derived from petroleum.However, such synthetic tensioactive agents are generally toxic and difficult to break down through the action of microorganisms.In recent years, such problems have motivated the scientific community to seek surfactants that are more environmentally friendly, such as those achieved through microbial production, known as biosurfactants [5].Moreover, concerns regarding the environment on the part of consumers and new environmental control legislation have led to the development of natural surfactants as an alternative to existing products.

Studies involving biosurfactants began in the 1960s and the use of these compounds has expanded in recent decades [2,6].Biosurfactants have drawn the interest of different industries due to advantag s such as structural diversity, low toxicity, greater biodegradability, ability to function in wide ranges of pH, temperature and salinity as well as greater selectivity, lower CMC and production involving renewable sources/industrial waste and industrial by-products [7][8][9].The present review demonstrates the reasons for which biosurfactants are considered the multifunctional materials of the 21st century, with a description of concepts, properties, classification, modes of production, physiology and uses in the most diverse industries.


Producing Microorganisms

Microorganisms use a set of carbon sources and energy for growth.The combination of carbon sources with insoluble substrates facilitates the intracellular diffusion and prod

tion of different substan
es [10][11][12].Microorganisms (yeasts, bacteria and some filamentous fungi) are capable of producing biosurfactants with different molecular structures and surface activities [4].In recent decades, there has been an increase in scientific interest regarding the isolation of microorganisms that produce tensioactive molecules with good surfactant characteristics, such as a low CMC, low toxicity and high emulsifying activity [2].

The literature describes bacteria of the genera Pseudomonas and Bacillus as great biosurfactant producers [2].However, most biosurfactants of a bacterial origin are inadequate for use in the food industr due to their possible pathogenic nature [13].Candida bombicola and Candida lipolytica are among the most commonly studied yeasts for the production of biosurfactants.A key advantage of using yeasts, such as Yarrowia lipolytica, Saccharomyces cerevisiae and Kluyveromyces lactis, resides in their "generally regarded as safe" (GRAS) status.Organisms with GRAS status do not offer the risks of toxicity or pathogenicity, which allows their use in the food and pharmaceutical industries [4].Table 1 displays a list of microorganisms that produce biosurfactants.


Classification

Most biosurfactants are either anionic or neutral, whereas those that contain amine groups are cationic.The hydrophobic moiety has long-chain fatty acids and the hydrophilic moiety can be a c

bohydrate, cycl
c peptide, amino acid, phosphate carboxyl acid or alcohol.The molar mass of biosurfactants generally ranges from 500 to 1500 Da [14].Biosurfactants are generally categorised by their microbial origin and chemical composition, as follows [3,5,15].


Glycolipids

Rhamnolipids, sophorolipids and trehalolipids are the best known glycolipids [16].Rhamnolipids were found as exoproducts of the pathogen P. aeruginosa and are a combination of α-L-rhamnopyranosylα-

rhamnopyrano
yl-β-hydroxydecanoyl-β-hydroxydecanoate (Rha-Rha-C10-C10) and α-L-rhamnopyranosyl-α-L-rhamnopyranosyl-β-hydroxydecanoate (Rha-Rha-C10) as well as their mono-rhamnolipid congeners (Rha-C10-C10 and Rha-C10) [17].Sensitive analytical techniques have led to the discovery of rhamnolipid congeners and homologues (approximately 60) produced at different concentrations by species of Pseudomonas and bacteria belonging to other families, classes or even phyla [16].For instance, various species of Burkholderia have been shown to produce rhamnolipids that have longer alkyl chains than those produced by P. aeruginosa [17][18][19].Surface tensions values of 29 mN/m constitute a characteristic of such components, which can be produced using different substrates, such as alkanes, pyruvate, citrates, fructose, glycerol, olive oil and glucose [20].Most studies involving rhamnolipids focus mainly on assessing the biodegradation efficiency of petroleum hydrocarbons [21,22].Although researchers have found increased dissipation of target contaminant upon the addition of rhamnolipids, a decrease in biodegradation efficiency or no effect following rhamnolipid supplementation have also been reported [16,20].The presence of surfactant molecules may induce changes in the microbial community, which, in turn, correspond to different degradation patterns.Interestingly, although rhamnolipids are considered biodegradable, few reports have demonstrated that these substances can be co-degraded or solely utilised as a carbon and energy source by various monocultures [18].Rhamnolipids are described as potentially toxic to natural vegetation [23], but have also been found to reduce the toxicity of specific compounds by increasing hydrocarbon solubilisation, thereby facilitating biodegradation [24,25].


Ustilago maydis

Sophorolipids are produced by yeasts that belong to the genus Candida [26,27].These glycolipids have a dimeric carbohydrate sophorose linked to a long-chain hydroxyl fatty acid through a glycosidic bond.Sophorolipids and lactone form a sophorolipid that is preferable in many applications [28,29].C. bombicola stands out among the different types of yeasts used in the production of these biosurfactants.Surface tension values of approximately 33 mN/m and a reduction in the surface tension of n-hexadecane and water from 40 to 5 mN/m has been recorded for these agents [30].Mannosylerythritol lipids (MEL), which are yeast glycolipids, are one of the most promising biosurfactants known and are abundantly produced from vegetable oils by Pseudozyma (previously Candida) antarctica [31].Trehalolipids are produced by species of Mycobacterium, Nocardia and Corynebacterium.Trehalolipids from Arthrobacter spp.and Rhodococcus erythropolis are able to lower surface and interfacial tensions in culture broth to 25-40 and 1-5 mN/m, respectively [5].


Fatty Acids, Phospholipids and Neutral Lipids

Different bacteria and yeasts produce large amounts of fatty acids and phospholipid surfactants during growth on n-alkanes.Phosphatidyl ethanolamine-rich vesicle

are produced from Acinetobacter spp.and form o
tically clear microemulsions of alkanes in water.These biosurfactants are essential to medical applications.According to Gautam and Tyagi [28], phospholipid protein complex deficiency is the major cause of respiratory failure in the children born prematurely.The authors also suggest that the isolation and cloning of genes involved in the production of surfactants can be used in fermentative processes [28].


Polymeric Biosurfactants

Emulsan, lipomanan, alasan, liposan and other polysaccharide protein complexes are the best-studied polymeric biosurfactants.Emulsan is an emulsifier for hydrocarbons in water at concentr

ions as low as 0.001% to
.01% [31,32].Liposan is an extracellular water soluble emulsifier synthesised by C. lipolytica and is made up of 83% carbohydrates and 17% proteins.Chakrabarti [33] discuss the application of liposan as an emulsifier in the food and cosmetic industries.


Particulate Biosurfactants

Particulate biosurfactants partition extracellular membrane vesicles to form a microemulsion that exerts an influence on alkane uptake in microbial cells.The Acinetobacter spp.has vesicles

ith a diameter of 20 to 50
m and a buoyant density of 1.158 cubic gcm composed of proteins, phospholipids and lipo-polysaccharides [5,33].

Figure 4 illustrates the chemical structure of the most studied microbial surfactants.Table 1 also displays biosurfactant classes and their producers.


Properties

It is necessary to submit a biosurfactant to conservation methods to evaluate its properties (surface tension and dispersion) over a period of 120 days to estimate the commercial validity of the product.Thus,

eating meth
ds are used separately or in combination with potassium sorbate, which is a conservative that inhibits the growth of mould that is widely used in the production and


Properties

It is necessary to submit a biosurfactant to conservation methods to evaluate its properties (surface tension and dispersion) over a period of 120 days to estimate the commercial validity of the product.Thus, h

ting method
are used separately or in combination with potassium sorbate, which is a conservative that inhibits the growth of mould that is widely used in the production and conservation of foods.Some characteristics are common to the majority of biosurfactants and have advantages over conventional surfactants, as described below [5].


Surface and Interfacial Activity

Efficiency and effectiveness are essential characteristics of a good surfactant.Efficiency is measured by the CMC, whereas effectiveness is related to surface and interfacial tensions [34].T

CMC of biosurfactants ranges fro
1 to 2000 mg/L, whereas interfacial (oil/water) and surface tensions are respectively approximately 1 and 30 mN/m.Good surfactants are able to reduce water surface tension from 72 to 35 mN/m and the interfacial tension of n-hexadecane from 40 to 1 mN/m.


Tolerance to Temperature, pH and Ionic Strength

Many biosurfactants can be used at high temperatures and pH values ranging from 2 to 12. Biosurfactants also tolerate a salt concentration up to 10%, whereas 2% NaCl is enough to

nactivate synthetic surfactants.


Biodegradabil
ty

Biosurfactants are easily degraded by microorganisms in water and soil, making these compounds adequate for bioremediation and waste treatment.


Low Toxicity

Low degree of toxicity allows the use of biosurfa

ants in foods, co
metics and pharmaceuticals.Low toxicity is also of fundamental importance to environmental applications.

Biosurfactants can be produced from la

ely available
raw materials as well as industrial waste.


Specificity

Biosurfactants are complex molecules with specific functional groups and therefore often have specific action.This is of particular interest in the detoxification of different pollutants and the de-emulsification of

ndustrial em
lsions as well as specific food, pharmaceutical and cosmetic applications.


Biocompatibility and Digestibility

These properties allow the use of biomolecules in different industries, especially the food, pharmaceutical and cosmetic industries.


Emulsion Forming/Breaking

Biosurfactants can be either em

sifiers or de-emulsifiers.An emulsi
n is a heterogeneous system consisting of an immiscible liquid dispersed in another liquid in the form of droplets, the diameter of w

ch generally exceeds 0.1 m
.There are two basic types of emulsion: oil-in-water (o/w) and water-in-oil (w/o).Emulsions have minimal stability, but the addition of biosurfactants can lead to an emulsion that remains stable for months or even years [35].Liposan, which is a water-soluble emulsifier synthesised by C. Lipolytica, has been used with edible oils to form stable emulsions.Liposan is commonly used in the cosmetic and food industries for producing stable oil/water emulsions [4,36].


Factors Affecting Biosurfactant Production

The production of biosurfactants can be either spontaneous or induced by the presence of lipophilic compounds, variations in pH, temperature, aeration and agitation speed or when cell growth

s maintained under conditions of stress, su
h as a low concentration of nitrogen [37].The various physicochemical factors are discussed below [38].


Carbon Source

The carbon source plays an important role in the growth and production of biosurfactants by microorganisms and varies from species to species.A very low yield was found when only either glucose or vegetable oil was used

r the producti
n of a biosurfactant by T. bombicola, but the yield increased to 70 g/L when both carbon sources were provided together [39].At a concentration of 80 and 40 g/L of glucose and soybean oil, respectively, the maximum yield of sophorose lipids was obtained by T. bombicola [40].Even higher yields of sophorolipids (120 g/L) were produced with C. bombicola in eight days when sugar and oil were used as carbon sources [41].When canola oil and glucose were used as carbon sources at concentrations of 10% each, maximum yield of sophorolipids (8 g/L) was obtained from C. lipolytica [42].Moreover, when industrial waste was used for the production of a biosurfactant by C. lipolytica, the yield of the protein-lipid-carbohydrate complex was 4.5 g/L, with a reduction in the surface tension of distilled water from 71 to 32 mN/m [43].A high production of bioemulsifier was obtained with C. lipolytica when supplemented with 1.5% glucose (w/v) [44].C. antarctica and C. apicola yielded 13.4 and 7.3 g/L of sophorolipids, respectively, when soapstock was used at a concentration of 5% (v/v) [45].The resting cells of Pseudozyma (C.antarctica) were found to covert C 12 to C 18 n-alkanes into mannosylerythritol lipids (MEL); the yield was 140 g/L after four weeks and the biosurfactant was able to emulsify soybean oil [46].A change in the fatty acid constitution of the final biosurfactant occurred when the fatty acid composition was changed in the fermentation medium containing C. ingens [47].


Nitrogen Sources

This is the second most important supplement for the production of biosurfactants by microorganisms.In fermentative processes, the C/N ratio affects the buildup of metabolites.High C/N ratios (i.e., low nitrogen levels) limit b

terial growth, fa
ouring cell metabolism towards the production of metabolites.In constrast, excessive nitrogen leads to the synthesis of cellular material and limits the buildup of products [48].Different organic and inorganic nitrogen sources have been used in the production of biosurfactants.Santa Anna et al. [49] describe the importance of nitrogen for the production of a biosurfactant by P. aeruginosa cultivated in a mineral medium containing 3% glycerol.As NaNO 3 proved more effective than (NH 4 ) 2 SO 4 , nutritional limitations clearly guide the cell metabolism to the formation of the product.Mulligan and Gibbs [50] report that P. aeruginosa uses nitrates, ammonium and amino acids as nitrogen sources.Nitrates are first reduced to nitrite and then ammonium.Ammonium is assimilated either by glutamate dehydrogenase (EC 1.4.1.4)to form glutamate or glutamine synthetase (EC 6.3.1.2) to form glutamine.Glutamine and α-ketoglutarate are then converted to glutamine by L-glutamine 2-oxoglutarate aminotransferase (EC 1.4.1.13).However, lipid formation rather than sugar is the rate-determining factor in the biosynthesis of rhamnolipids and nitrogen limitation can lead to the accumulation of lipids.In comparison to ammonium, the assimilation of nitrate is slower and simulates nitrogen limitation, which is favourable to the production of rhamnolipids.High yields of sophorose lipids, which are biosurfactants produced by the fungi T. bombicola and C. Bombicola, have been achieved using yeast extract and urea as the nitrogen source [51].Moreover, high yields of mannosylerythritol lipid by Candida sp.SY16, C. lipolytica and C. glabrata have been achieved with ammonium nitrate and yeast extract [42,43,46,[52][53][54].


Growth Conditions

Growth conditions (temperature, pH, agitation speed and oxygen) also influence biosurfactant production [37].Species of the genus Candida produce maximum biosurfactant yields in a wide pH range, such as pH 5.7 for C. glabrata UCP 1002, pH 7.8

or Candida sp.SY16
pH 5.0 for C. Lipolytica and pH 6.0 for C. batistae [52,[54][55][56].Moreover, Pichia anamola and Aspergillus ustus produce maximum biosurfactant yield at pH 5.5 and 7.0, respectively [57,58].Different microbial processes are affected by even a small change in temperature.The most favourable temperature for the production of biosurfactants by different fungi is 30 ˝C, as observed for different species of Candida, viz.Candida sp.SY16, C. bombicola, C. batistae and T. bombicola [39,51,52,56].In case of C. lipolytica, 27 ˝C has been found to be the best temperature.Incubation time also exerts a significant effect on biosurfactant production.Microorganisms produce biosurfactants in different time intervals.Maximum biosurfactant production by Aspergillus ustus was found after five days of incubation, whereas the incubation periods for C. bombicola were seven, eight and 11 days [59,60].Maximum biosurfactant production by C. bombicola grown in animal fat was found after 68 h of incubation [49].Moreover, an increase in agitation speed favoured the accumulation of a biosurfactant by P. aeruginosa UCP 0992 grown in glycerol [61].Oliveira et al. [62] studied the effect of a change in agitation speed of cultures from 50 to 200 rpm on P. alcaligenes cultivated in palm oil.The authors found that the increase in rotation velocity favoured a reduction in the surface tension of the cell-free broth to 27.6 mN/m.In contrast, Cunha et al. [63] found that agitation had a negative effect regarding a reduction in surface tension using a biosurfactant from Serratia sp.SVGG16 grown in a hydrocarbon culture.


Metabolic Pathways of Biosurfactant Production

Hydrophilic substrates are primarily used by microorganisms for cell metabolism and the synthesis of the polar moiety of a biosurfactant, whereas hydrophobic substrates are used exclusively for the production of the hydrocarbon

rtion of the biosurfactant [37,64].Diverse meta
olic pathways are involved in the synthesis of precursors for biosurfactant production and depend on the nature of the main carbon sources employed in the culture medium.For instance, when carbohydrates are the only carbon source for the production of a glycolipid, the carbon flow is regulated in such as way that both lipogenic pathways (lipid formation) and the formation of the hydrophilic moiety through the glycolytic pathway are suppressed by the microbial metabolism, as illustrated in Figure 5 [65].

A hydrophilic substrate, such as glucose or glycerol, is degraded until forming intermediates of the glycolytic pathway, such as glucose 6-phosphate, which is one of the main precursors of carbohydrates found in the hydrophilic moiety of a biosurfactant.For the production of lip ds, glucose is oxidised to pyruvate through glycolysis and pyruvate is then converted into acetyl-CoA, which produces malonyl-CoA when united with oxaloacetate, followed by conversion into a fatty acid, which is one of the precursors for the synthesis of lipids [66].When a hydrocarbon is used as the carbon source, however, the microbial mechanism is mainly directed to the lipolytic pathway and gluconeogenesis (the formation of glucose through different hexose precursors), thereby allowing its use for the production of fatty acids or sugars.The gluconeogenesis pathway is activated for the production of sugars.This pathway consists of the oxidation of fatty acids through β-oxidation to acetyl-CoA (or propionyl-CoA in the case of odd chain fatty acids).Beginning with the formation of acetyl-CoA, the reactions involved in the synthesis of polysaccharide precursors, such as glucose 6-phosphate, are essentially the inverse of those involved in glycolysis.However, reactions catalysed by pyruvate kinase and phosphofructokinase-1 are irreversible.Thus, other enzymes exclusive to the process of gluconeogensis are required to avoid such reactions.Figure 6 illustrates the main reactions through to the formation of glucose 6-phosphate, which is the main precursor of polysaccharides and disaccharides formed for the production of the hydrophilic moiety of glycolipids [67].A hydrophilic substrate, such as glucose or glycerol, is degraded until forming intermediates of the glycolytic pathway, such as glucose 6-phosphate, which is one of the main precursors of carbohydrates found in the hydrophilic moiety of a biosurfactant.For the production of lipids, glucose is oxidised to pyruvate through glycolysis and pyruvate is then converted into acetyl-CoA, which produces malonyl-CoA when united with oxaloacetate, followed by conversion into a fatty acid, which is one of the precursors for the synthesis of lipids [66].When a hydrocarbon is used as the carbon source, however, the microbial mechanism is mainly directed to the lipolytic pathway and gluconeogenesis (the formation of glucose through different hexose precursors), thereby allowing its use for the production of fatty acids or sugars.The gluconeogenesis pathway is activated for the production of sugars.This pathway consists of the oxidation of fatty acids through β-oxidation to acetyl-CoA (or propionyl-CoA in the case of odd chain fatty acids).Beginning with the formation of acetyl-CoA, the reactions involved in the synthesis of polysaccharide precursors, such as glucose 6phosphate, are essentially the inverse of those involved in glycolysis.However, reactions catalysed by pyruvate kinase and phosphofructokinase-1 are irreversible.Thus, other enzymes exclusive to the process of gluconeogensis are required to avoid such reactions.Figure 6 illustrates the main reactions through to the formation of glucose 6-phosphate, which is the main precursor of polysaccharides and disaccharides formed for the production of the hydrophilic moiety of glycolipids [67].According to Sydatk and Wagner [68], the biosynthesis of a surfactant occurs through four different routes: (a) carbohydrate and lipid synthesis; (b) synthesis of the carbohydrate half while the synthesis of the lipid half depends on the length of the chain of the carbon substrate in the medium; (c) synthesis of the lipid half while the synthesis of the carbon half depends on the substrate employed; and (d) synthesis of the carbon and lipid halves, which are both dependent on the substrate.Therefore, the length of the n-alkane chain used as the carbon source alters the biosynthesis of a surfactant.Kitamoto et al. [46] studied the production of manosilerythritol lipid (MEL) by the yeast C. antarctica in the presence of different n-alkanes and found that this species does not grow or produce a biosurfactant in media containing C 10 to C 18 .However, production occurred when the species was grown in a medium containing C 12 to C 18 and octadekane as substrate led to the greatest yield.In contrast, production was minimal in media containing n-alkanes with more than 19 carbons.According to Sydatk and Wagner [68], the biosynthesis of a surfactant occurs through four different routes: (a) carbohydrate and lipid synthesis; (b) synthesis of the carbohydrate half while the synthesis of the lipid half depends on the length of the chain of the carbon substrate in the medium; (c) synthesis of the lipid half while the synthesis of the carbon half depends on the substrate employed; and (d) synthesis of the carbon and lipid halves, which are both dependent on the substrate.Therefore, the length of the n-alkane chain used as the carbon source alters the biosynthesis of a surfactant.Kitamoto et al. [46] studied the production of manosilerythritol lipid (MEL) by the yeast C. antarctica in the presence of different n-alkanes and found that this species does not grow or produce a biosurfactant in media containing C10 to C18.However, production occurred when the species was grown in a medium containing C12 to C18 and octadekane as substrate led to the greatest yield.In contrast, production was minimal in media containing n-alkanes with more than 19 carbons.


Physiology

Biosurfactants are produced by microorganisms either through excretion or adhesion to cells, especially when cultivated on substrates that are insoluble in water.While the function in microbial cells is not yet fully understood, it has been speculated that biosurfactants are involved in the e

lsification
of insoluble substrates [37,69].

The main physiological role of biosurfactants is to allow microorganisms to grow on substrates that are insoluble in water through a reduction in surface tension between phases, making the substrate more available for uptake and metabolism.The uptake mechanisms of these substrates (such as, alkanes) are no yet fully clarified.The direct uptake of dissolved hydrocarbons in the aqueous phase, direct contact between cells and large hydrocarbon droplets, and the interaction with emulsified droplets (emulsion) have been described.Besides the emulsification of the carbon source, biosurfactants are also involved in the adhesion of microbial cells to hydrocarbons, as discussed in


Physiology

Biosurfactants are produced by microorganisms either through excretion or adhesion to cells, especially when cultivated on substrates that are insoluble in water.While the function in microbial cells is not yet fully understood, it has been speculated that biosurfactants are involved in the emulsi

cation of i
soluble substrates [37,69].

The main physiological role of biosurfactants is to allow microorganisms to grow on substrates that are insoluble in water through a reduction in surface tension between phases, making the substrate more available for uptake and metabolism.The uptake mechanisms of these substrates (such as, alkanes) are not yet fully clarified.The direct uptake of dissolved hydrocarbons in the aqueous phase, direct contact between cells and large hydrocarbon droplets, and the interaction with emulsified droplets (emulsion) have been described.Besides the emulsification of the carbon source, biosurfactants are also involved in the adhesion of microbial cells to hydrocarbons, as discussed in the following sections.Microorganism cell adsorption to insoluble substrates and the excretion of surfactant compounds allow growth on carbon sources [37].


Fermentation Kinetics

Biosurfactant production kinetics has considerable variation among different systems.For convenience, kinetic parameters are grouped as follows: (a) growth-associated production; (b) production under growth-limiting conditions; (c) production by resting or immobilised cells; and (d) producti

with precursor supple
entation [37].In growth-associated production, parallel relationships are found between growth, the use of the substrate and biosurfactant production.Production under growth-limiting conditions is characterised by an accentuated increase in biosurfactant concentration as a result of the limitation of one or more medium components.Production by resting or immobilised cells is a type of biosurfactant production in which there is no cell multiplication; the cells nonetheless continue to use the carbon source for biosurfactant synthesis.Investigators report that the addition of biosurfactant precursors to the medium leads to qualitative and quantitative changes in the final product.


Raw Materials for Biosurfactant Production

Current society is characterised by an increase in expenditures, the need to reuse materials and environmental concerns.Consequently, greater emphasis has been given to recovery, recycling and reuse.Indeed, the need for environmental preservation has led to the reuse of diffe

nt industrial wastes.This is particularly v
lid for the food production industry, the waste products, effluents and by-products of which can be reused [70].Industrial waste had piqued the interest of researchers as a low-cost substrate for biosurfactant production [71].The selection of waste products should ensure the proper balance of nutrients to allow microbial growth and consequent biosurfactant production.Industrial waste with a high content of carbohydrates or lipids is ideal for use as substrate [71].According to Barros et al. [34], the use of agro-industrial waste is one of the steps towards the implantation of feasible biosurfactant production on an industrial scale, for which the optimisation of the different variables involved is required.

The literature describes a number of waste products employed in biosurfactant production, such as vegetable oils, oily effluents [42,72,73], starchy effluents [74,75], animal fat [51,[76][77][78], vegetable fat [79], vegetable cooking oil waste [72,[80][81][82], soapstock [76,83,84] molasses [85][86][87][88], dairy industry wa te (whey) [89], corn steep liquor [43,71,[90][91][92], cassava flour wastewater [93], oil distillery waste [43,90,94,95] and glycerol [61].Some of the most commonly employed industrial waste products for biosurfactant production are detailed below.


Olive Oil Mill Effluent (OOME)

Olive Oil Mill Effluent (OOME) is a concentrated black liquor with a water-soluble portion of ripe olives and water that is used for the extraction of olive oil.OOME has polyphenols that represent a challenge in terms of the environment disposal.However, it also contains nitrogen compounds (12 t

24 g/L), sugars (20 to 80 g/L),
residual oil (0.3 to 5 g/L) and organic acids (5 to 15 g/L).Mercade et al. [73] successfully employed OOME for the strain Pseudomonas sp. to produce rhamnolipids.


Animal Fat

Animal fat and lard can be obtained in large quantities from the meat processing industry and have been used as a medium for cooking foods.Recently, however, such fats have lost a large part of the market to vegetable oils due to the lower degree of harm to health caused by the latter [70].Animal fat stimulates the pr

uction of s
phorolipids by the yeast C. bombicola [51].Using animal fat and corn steep liquor, Santos et al. [77,78] achieved maximum glycolipid production by the yeast C. lipolytica UCP 0988.The authors also report that the product has uses in bioremediation as well as oil mobilisation and recovery.


Frying Oils

Fry oil and edible fats are considered great carbon sources for biosurfactant production.Vegetable oils constitute a lipid carbon source and are mainly comprised of saturated or unsaturated fatty acids with chains of 16 to 18 carbon atoms [9].Different oils are adequate substrates for biosurfactants.Babassu oil (5% v/v)

th a carbon
ource (1% glucose w/v) is a good medium for biosurfactant production.Sarubbo et al. [96] found that two strains of C. lipolytica (1055 and 1120) produce biosurfactants toward the final of the exponential growth phase and onset of the stationary phase.Sunflower and olive oils have proven to be adequate energy and carbon sources for the production of biosurfactants.P. aeruginosa strains produce a biosurfactant on residue from corn, soybean and canola oil plants [97,98].Canola oil residue and sodium nitrate has been reported adequate for microbial growth and the production of up to 8.50 g/L of rhamnoipids.The combination of glucose and canola oil has been used for the successful production of a biosurfactant by C. lipolytica [42].


Soapstocks

Oil cakes or soapstocks are produced from oilseed processing involving the refining of seed-based edible oils with the use of chemicals [76].Soapstock has been used together with sunflower oil, olive oil or soybean oil as substates to produce rhamnolipids.Yields as high as 15.9 g/L have been reported using P. aeruginosa in a soap

and brow
colour.The high sugar content (48%-56%) makes molasses adequate for biosurfactant production by different microorganisms.Laboratories have used molasses for the production of different microbial metabolites.According to Makkar and Cameotra [88], Bacillus subtilis in a minimal medium supplemented with molasses as the carbon source produces a biosurfactant.Joshi et al. [99] used molasses as well as other carbon sources to produce biosurfactants from strains of Bacillus.


Whey

The dairy industry produces large quantities of whey, such as whey waste, cheese whey, curd whey and lactic whey, all of which can be used as substrates for the microbial production of metabolites [70,[100][101][102].A high amount of lactose (approximately 75%) is found in lactic whey.Other components, such as proteins, vitamins and organic acids

are g
od sources for microbial growth and biosurfactant production [75].Moreover, whey disposal represents a major pollution problem, especially in countries that depend on a dairy economy [103].Thus, the disposal of this by-product represents a waste of a widely available substrate and an environmental hazard.


Corn Steep Liquor

The agro-industry of corn-based products through wet processing results in both solid and liquid by-products, which, when disposed improperly, become a source of contamination and harm to the environment.Corn steep liquor is a by-product of the washing water and soaking of kernels as well as fractioning into starch and germen (oil) that

ntains 40% solid m
tter.This by-product consists of 21% to 45% proteins, 20% to 26% lactic acid, approximately 8% ash (containing Ca 2+ , Mg 2+ , K + , etc.), approximately 3% carbohydrates and a low fat content (0.9% to 1.2%) [103][104][105].Nut oil refinery residue and corn steep liquor are low-cost nutrients for the production of glycolipids by C. sphaerica (UCP 0995).The biosurfactant of this strain mobilises and removes up to 95% of motor oil on sand, making it useful for bioremediation [89,94,106].Silva et al. [107] also report the production of a biosurfactant from P. cepacia grown in mineral medium supplemented with 2.0% corn steep liquor and 2.0% soybean waste frying oil.


Starchy Substrates

Abundant starch-based substrates also constitute renewable carbon sources.The potato processing industry produces significant amounts of starch-rich waste that are adequate for biosurfactant production.Besides the approximately 80% water content, potato waste has carbohydrates (17%), proteins (2%) and fats (0.1%) as well as inorganic mineral

trace elements and
vitamins [103].As an example, Fox and Bala investigated a commercially prepared potato starch in a mineral salt medium for the production of a biosurfactant by B. subtilis [74].Cassava wastewater, which is another carbohydrate-rich waste product generated in large amounts, has been used for the production of surfactin by B. Subtilis 35.Other starchy wastes, such as rice water and cereal processing wastewater, have the potential to permit microbial growth and biosurfactant production [108].


Recovery of Biosurfactants

The production of low-coast biosurfactants is unlikely due to the complicated recovery process.Process development is conduted in order to obtain biosurfactants that can be recovered easily and inexpensively.In many biotechnological processes, downstream processing accounts for 70%-80% of production costs.For economic reasons, most biosur

ctant production processes
eed to involve spent whole-cell culture broths or other crude preparations [11,103,109].Extraction with chloroform-methanol, dichloromethane-methanol, butanol, ethyl acetate, pentane, hexane, acetic acid, ether, etc. constitutes the most commonly used method in biosurfactant downstream processing.The most widely employed products are different ratios of chloroform and methanol, which facilitate the adjustment of the polarity of the extraction agent to the extractable target material.The disadvantages of using organic solvents for biosurfactant recovery include the large amount of solvent required and the increase in production costs due to the price of expensive solvents.Chloroform is a toxic chloro-organic compound that is harmful to human health and the environment.Thus, there is a need for inexpensive solvents with low toxicity for biosurfactant extraction processes that are suitable for industrial applications.Other product precipitation techniques have also been reported, such as precipitation with ammonium sulphate, centrifugation and adsorption.Biosurfactant recovery depends mainly on the ionic charge, water solubility and location (intracellular, extracellular or cell bond) [103,109].Foam fractionation is a solvent-free method that separates biosurfactant molecules adsorbed to air bubbles in the culture medium.Biosurfactant production involves continuous foam formation due to the high surface activity.Foam in the broth interferes with mass and heat transfer processes, thereby affecting productivity.However, foam is beneficial to biosurfactant production, as it assists in the continuous removal of product, and therefore production and recovery processes can be accomplished in a single stage [110].Continuous foam fractionation in the fermentation process helps prevent the accumulation of product that could otherwise inhibit biomass growth and product formation and also facilitates extended biosurfactant production in fed-batch or continuous mode operations.Moreover, biosurfactants do not readily undergo denaturation due to their small size and simple structure [111].

More research and development are required to optimise existing recovery processes to make such processes both commercially viable and more competitive [39,103].Table 2 lists the most common biosurfactant recovery techniques and their advantages.


Industrial Applications of Biosurfactants

Biosurfactants have a wide range of biotechnological applications in petroleum, foods, bevera es, cosmetics, detergents, textiles, paints, mining, cellulose, pharmaceutics and nanotechnology [112].Currently, the main market is the petroleum industry.Biosurfactants can be used for oil residue recovery from storage tanks, other oil recovery pr

esses, the cleanup of oil spills and the b
oremediation of both soil and water [2,113].Table 3 offers a summary of the uses of biosurfactants in different industries.The main biotechnological applications are detailed in the following sections.


Petroleum Recovery

Petroleum is an essential energy source and driving force of economic development.The US Department of Energy reports that fossil fuels constitute 83% of all primary energy sources in the country and petroleum accounts for 57% of such products.Indeed, 19.2 million cubic metres of petroleum were consumed per day in 2010 [114].The USA produces 870,000 m 3 of crude oil f

m 530 thousand prod
ction wells, 35% of which produce 0.16 m 3 /day and 79% produce < 1.59 m 3 /day [115].Through oil recovery processes, these oil wells produce only one third to half of the petroleum originally present at the sites.Oil residue in small pores within petroleum reservoirs accounts for 50% to 65% of oil and is trapped by high forces of capillarity as well as interfacial tension between the hydrocarbon and aqueous phases.Different reductions in interfacial tension are needed for the mobilisation of this hydrocarbon [116,117], which is only achieved with the use of surfactant concentrations significantly higher than that required for the formation of micelles [118,119].In enhanced oil recovery, the use of heat, tensioactive agents, microbial processes and gas injection leads to the recovery of a significant portion of the retained oil.However, the high cost of chemical tensioactive agents hinders widespread use of surfactants in oil recovery processes.Thus, biosurfactants have been employed to reduce the interfacial tension between oil/water and oil/rock, which leads to a reduction in the capillary forces that impede oil from moving through rock pores (Figure 7).Biosurfactants also form an emulsion at the oil-water interface, which stabilises the desorbed oil in water and allows oil removal along with the injection water [1,8].


Industrial Applications of Biosurfactants

Biosurfactants have a wide range of biotechnological applications in petroleum, foods, beverages, cosmetics, detergents, textiles, paints, mining, cellulose, pharmaceutics and nanotechnology [112].Currently, the main market is the petroleum industry.Biosurfactants can be used for oil residue recovery from storage tanks, other oil recovery processes, the cl

nup of oil spills and the bioremediation o
both soil and water [2,113].Table 3 offers a summary of the uses of biosurfactants in different industries.The main biotechnological applications are detailed in the following sections.


Petroleum Recovery

Petroleum is an essential energy source and driving force of economic development.The US Department of Energy reports that fossil fuels constitute 83% of all primary energy sources in the country and petroleum accounts for 57% of such products.Indeed, 19.2 million cubic metres of petroleum were consumed per day in 2010 [114].The USA produces 870,000 m 3 of crude oil from 530 thousan

production wells, 3
% of which produce 0.16 m 3 /day and 79% produce < 1.59 m 3 /day [115].Through oil recovery processes, these oil wells produce only one third to half of the petroleum originally present at the sites.Oil residue in small pores within petroleum reservoirs accounts for 50% to 65% of oil and is trapped by high forces of capillarity as well as interfacial tension between the hydrocarbon and aqueous phases.Different reductions in interfacial tension are needed for the mobilisation of this hydrocarbon [116,117], which is only achieved with the use of surfactant concentrations significantly higher than that required for the formation of micelles [118,119].In enhanced oil recovery, the use of heat, tensioactive agents, microbial processes and gas injection leads to the recovery of a significant portion of the retained oil.However, the high cost of chemical tensioactive agents hinders widespread use of surfactants in oil recovery processes.Thus, biosurfactants have been employed to reduce the interfacial tension between oil/water and oil/rock, which leads to a reduction in the capillary forces that impede oil from moving through rock pores (Figure 7).Biosurfactants also form an emulsion at the oil-water interface, which stabilises the desorbed oil in water and allows oil removal along with the injection water [1,8].


Bioremediation

Oil spills occur during cargo transportation or in the form of industrial oil and by-product spills.Petroleum exerts a negative effect on cell membranes in living organisms, offering considerable risk of contamination to both marine and terrestrial ecosystems [2,114].

The US Environmental Protection Agency proposes different physical, chemical and biological technologies for the treatment of contam

ated soil [126]
one of the most studied of which is bioremediation.This process involves the natural degradation capacity of plants and microorganisms for either the partial conversion of contaminants into less toxic compounds or the complete conversion of such substances into carbon ioxide and water.

Larger degrading microorganism populations lead to a quicker, more efficient bioremediation processes.Therefore, this technique can be conducted through biostimulation, which consists of stimulating the growth of microorganisms present at the contaminated site.The process involves the introduction of specific electron receptors, oxygen and nutrients for the degradation of the contaminant as well as substances to corre t the pH.Bioremediation can also be performed through bioaugmentation, in which indigenous (allochthonous) microorganisms are added to the contaminated environment to accelerate and complete the degradation of the pollutant [114].

Bioremediation played an important role in the cleanup of the 41 million litre oil spill caused by the oil tanker Exxon Valdez in the Gulf of Alaska in 1989, giving rise to the development of this technology and demonstrating that there are good reasons to believe in the effective application of this treatment method in future oil spills under the appropriate circumstances [114].In the accident with the Exxon Valdez, the first measure taken was physical washing with high-pressure water.Chemical surfactants were then applied in polluted areas to accelerate the growth and activity of petroleum-degrading microorganisms.Two or three weeks later, the regions treated with surfactants were significantly cleaner than control areas.However, it was difficult to evaluate the exact effects of the treatment due to the heterogeneity of the contamination.Nonetheless, subsequent studies have demonstrated the importance of the use of surfactants to enhance the biodegradation of oil [114,127].

While bioremediation is an effective, environmentally friendly method, the time and costs involved make this process unviable for the treatment of large amounts of waste [128].Thus, the use of biosurfactants emerges as a safe alternative for improving the solubility of hydrophobic compounds by allowing the desorption and solubilisation of hydrocarbons and facilitating the assimilation of these compounds by microbial cells [12 ].

The biodegradation of oil-derived hydrocarbons by biosurfactants occurs through two mechanisms.The first involves an increase in the bioavailability of the hydrophobic substrate to microorganisms, with a consequent reduction in surface tension of the medium around the bacterium as well as a reduction in interfacial tension between the cell wall and hydrocarbon molecules.The other mechanism involves the interaction between the iosurfactant and cell surface, leading to changes in the membrane, facilitating hydrocarbon adherence (increase in hydrophobicity) and reducing the lipopolysaccharide index of the cell wall without damaging the membrane.Thus, biosurfactants block the formation of hydrogen bridges and allow hydrophobic-hydrophilic interactions, which cause molecular rearrangements and reduce the surface tension of the liquid by increasing its surface area as well as promoting bioavailability and consequent biodegradability [130,131].Figure 8 illustrates the action of biosurfactants in increasing the surface area of oil droplets as well as facilitating access to a greater number of bacteria and consequently producing a greater biomass.


Removal of Hydrophobic Organic Pollutants

The application of biosurfactants for the removal of contaminants from soil is less well known than the advanced application of these compounds in bioremediation processes, since removal efficiency is driven mainly by the physicochemical properties of the biosurfactant rather than the effects on metabolic activity or changes in the properties of the cell surface.However, the mechanisms t

t affect the mobilisation and solubilisati
n of hydrocarbons in soils are similar to those involved in the enhancement of bioavailability for bioremediation [131,132].


Removal of Hydrophobic Organic Pollutants

The application of biosurfactants for the removal of contaminants from soil is less well known than the advanced application of these compounds in bioremediation processes, since removal efficiency is driven mainly by the physicochemical properties of the biosurfactant rather than the effects on metabolic activity or changes in the properties of the cell surface.However, the mechanisms tha

affect the mobilisation and solubilisation
of hydrocarbons in soils are similar to those involved in the enhancement of bioavailability for bioremediation [131,132].

Biosurfactants enhance the removal of hydrocarbons through biodegradation, solubilisation, mobilisation or emulsification [8].Solubilisation capacity depends on the ability of the surfactant to increase the solubility of hydrophobic components in the aqueous phase.A considerable increase in this capacity occurs above the CMC due to the partitioning of the hydrocarbon in the hydrophobic portion of the micelles.In this process, greater concentrations of surfactants are normally required, since the solubility of the hydrocarbon components in the solution depends wholly on the concentration of the surfactant [8].Mobilisation occurs at concentrations below the CMC and is divided into displacement and dispersion.Displacement consists of the release of hydrocarbon droplets from the porous medium due to the reduction in interfacial tension.Using a theoretical explanation, hydrocarbon removal is possible when the interfacial tension between the aqueous and oil phases is sufficiently reduced to overcome the forces of capillarity that cause the formation of residual saturation.Dispersion is a process by which a hydrocarbon is dispersed in the aqueous phase as tiny emulsions.Emulsions are not generally thermodynamically stable, but may remain stable for significant periods of time due to kinetic restrictions.Dispersion is related to interfacial tension and surfactant concentration and differs from displacement, which is related only to interfacial tension between the aqueous and hydrophobic phases, with no formation of emulsion [132].

The efficiency of a surfactant in the removal of hydrophobic compounds also depends on the pH and ionic strength of the solution, which can alter the arrangement of the aggregated micelles and sorption of the surfactant to the soil, which, in turn, limits the transport of the hydrocarbon by the surfactant.Different biosurfactants have been tested for the removal of petroleum-derived products from contaminated soil and water.Rhaminolipids have been successfully used in biotechnological decontamination processes [2,7,17].Other surfactants produced by species of Pseudomonas [110,133], Bacillus [5,134], and Candida [109,113,[135][136][137], have also been successfully used in the remediation of soil.


Removal of Heavy Metals

Heavy metals and radionuclides are persistent soil contaminants.Increases in levels of heavy metals in soil have been reported in many industrialised countries.Metals and metalloids, such as chromium, cadmium, mercury and lead, can threaten ecosystems and human health through either the food chain or direct exposure to contaminated soil and water [1,12].As different technologies can be used in combination for the treatm

t of organic pollutants
nd heavy metals, biosurfactants can be used in the removal of Biosurfactants enhance the removal of hydrocarbons through biodegradation, solubilisation, mobilisation or emulsification [8].Solubilisation capacity depends on the ability of the surfactant to increase the solubility of hydrophobic components in the aqueous phase.A considerable increase in this capacity occurs above the CMC due to the partitioning of the hydrocarbon in the hydrophobic portion of the micelles.In this process, greater concentrations of surfactants are normally required, since the solubility of the hydrocarbon components in the solution depends wholly on the concentration of the surfactant [8].Mobilisation occurs at concentrations below the CMC and is divided into displacement and dispersion.Displacement consists of the release of hydrocarbon droplets from the porous medium due to the reduction in interfacial tension.Using a theoretical explanation, hydrocarbon removal is possible when the interfacial tension between the aqueous and oil phases is sufficiently reduced to overcome the forces of capillarity that cause the formation of residual saturation.Dispersion is a process by which a hydrocarbon is dispersed in the aqueous phase as tiny emulsions.Emulsions are not generally thermodynamically stable, but may remain stable for significant periods of time due to kinetic restrictions.Dispersion is related to interfacial tension and surfactant concentration and differs from displacement, which is related only to interfacial tension between the aqueous and hydrophobic phases, with no formation of emulsion [132].

The efficiency of a surfactant in the removal of hydrophobic compounds also depends on the pH and ionic strength of the solution, which can alter the arrangement of the aggregated micelles and sorption of the surfactant to the soil, which, in turn, limits the transport of the hydrocarbon by the surfactant.Different biosurfactants have been tested for the removal of petroleum-derived products from contaminated soil and water.Rhaminolipids have been successfu ly used in biotechnological decontamination processes [2,7,17].Other surfactants produced by species of Pseudomonas [110,133], Bacillus [5,134], and Candida [109,113,[135][136][137], have also been successfully used in the remediation of soil.


Removal of Heavy Metals

Heavy metals and radionuclides are persistent soil contaminants.Increases in levels of heavy metals in soil have been reported in many industrialised countries.Metals and metalloids, such as chromium, cadmium, mercury and lead, can threaten ecosystems and human health through either the food chain or direct exposure to contaminated soil and water [1,12].As different technologies can be used in combination for the treatment of organic

llutants and heavy metal
, biosurfactants can be used in the removal of hydrophobic organic compounds and heavy metals [138][139][140].Heavy metals mainly adsorb to the surface of soil in the form of ions or the precipitation of metal compounds.Unlike organic contaminants, heavy metals are removed from soil through surfactant-associated complexation [141] and ion exchange [142].Therefore, surfactant-enhanced washing and surfactant-enhanced bio-extraction can be applied to the remediation of soils contaminated with heavy metals.

Surfactants in solutions facilitate the solubilisation, dispersion and desorption of contaminants and allow the reuse of the soil [143].Decontamination tests have been performed with different synthetic surfactants [144,145], but the desire to replace such compounds with natural surfactants has led to research into the use of biosurfactants [119].Studies have demonstrated the potential of surfactin, rhamnolipids and sophorolipids [146][147][148].The ionic nature, bi degradability, low toxicity and excellent surface properties make biosurfactants adequate for the removal of heavy metals from sediment and soil.According to Mulligan [119], removal is possible with different concentrations of biosurfactants.Das et al. [149] found that the removal of cadmium using an aqueous solution also occurred at concentrations below the CMC, while a concentration fivefold greater than the CMC resulted in the virtually complete removal of 100 ppm of metal ions.Wen et al. [150] studied the degradation of a rhamnolipid in soils contaminated by cadmium and zinc and found that this compound could remain in the soil long enough to enhance the phytoextraction of the metals.

The removal of metals by ionic biosurfactants is thought to occur in the following order (Figure 9): (1) sorption of the biosurfactant to the soil surface and complexation with the metal; (2) detachment of the metal from the soil to the solution; and (3) association with micelles.Heavy metals are trapped within the micelles through electrostatic interactions and can be easily recovered through precipitation or membrane separation methods [151].


Food Industry

Emulsifica ion is important for the formation of consistency and texture in foods as well as phase dispersion and the solubilisation of aromas [4,159].The general function of emulsifiers in food products is to stabilise the emulsion by controlling the agglomeration of fat globules and stabilising aerated systems [4,152].An emulsion has at least one immiscible liquid (discontinuous internal phase) dispersed in another (continuous outer phase) in the form of dr

lets.The stabi
ity of this system is minimal, but can be enhanced by the addition of a surfactant, which reduces surface energy between the two phases by a reduction in Anionic biosurfactants create non-ionic complexes with metals through ionic bonds.As such bonds are stronger than those between the metal and soil, the metal-biosurfactant complex is detached from the soil due to the reduction in interfacial tension.Cationic biosurfactants can replace similarly charged metal ions through ion exchange (competition for negatively charged surfaces).Surfactant micelles can also be used to remove metal ions from the soil surface [115].

Biosurfactants offer indisputable advantages, since surfactant-producing microorganisms do not need to survive in contaminated soil, although the continual addition of biosurfactant is required in the process [8].Biosurfactants have also been applied in mining processes.Tensioactive compounds produced by Pseudomonas sp. and Alcaligenes sp. have been used for the floatation and separation of calcite and scheelite, with recovery rates of 95% for CaWO 4 and 30% for CaCO 3 , whereas c nventional chemical reagents are not capable of separating these two minerals [152].Slizovskiy et al. [153] studied the enhanced remediation of soils contaminated with heavy metals using the cationic surfactant 1-dodecylpyridinium chloride (DPC), the non-ionic surfactant oleyl dimethyl benzyl ammonium chloride (trade name Ammonyx KP) and the ionic rhamnolipid biosurfactant (trade name JBR-425); the latter substance exhibited the best elution with regard to Zn (39%), Cu (56%), Pb (68%) and Cd (43%).Almeida et al. [154] studied the impact of surfactants on the removal of Cu by the salt marsh plant Halimione portulacoides.TX-100 and SDS (sodium dodecyl sulfate) were favourable to Cu harvesting and transportation in plant roots, but did not affect the transportation of Cu in the stem and leaves.The results of this study suggest that surfactants promote phytoremediation through a change in the membrane permeability of root cells.Therefore, surfactants can promote the desorption of metals and uptake by plants [1].

Rhamnolipids and soapberry-derived saponin have recently been found to assist in the removal of chromium and arsenic oxyanions from soils or the ore waste of mines [155,156].Biosurfactants produced by yeast of the genus Candida have been successfully used in heavy metal flotation, demonstrating the ability to remove more than 90% of cations in columns and air-dissolved flotation processes [157,158].C. lipolytica produces a biosurfactant that has also been used for the removal of heavy me als and petroleum byproducts using a soil barrier [90].The biosurfactant significantly reduced soil permeability, thereby demonstrating its usefulness in reactive barriers, with the removal of approximately 96% of Zn and Cu as well as a reduction in Pb and Cd concentrations in groundwater.


Food Industry

Emulsification is important for the formation of consistency and texture in foods as well as phase dispersion and the solubilisation of aromas [4,159].The general function of emulsifiers in food products is to stabilise the emulsion by controlling the agglomeration of fat globules and stabilising aerated systems [4,152].An emulsion has at least one immiscible liquid (discontinuous internal phase) dispersed in another (continuous outer phase) in the form of droplets.The stabi

ty of this sys
em is minimal, but can be enhanced by the addition of a surfactant, which reduces surface energy between the two phases by a reduction in interfacial tension, thereby preventing particle coalescence through the formation of steric and electrostatic barriers.Examples of processed foods that are emulsions include heavy cream, butter, mayonnaise, salad dressings, fillings, etc. [35].Other uses for emulsifiers have been described, such as improving the texture and shelf life of products containing starch, the formation of complexes, altering the rheological properties of wheat flour and interactions with gluten as well as improving the consistency and texture of fat-based products through the control of polymorphism and the crystalline structure of fats [4].

Biosurfactants can also be used as emulsifiers in the processing of raw materials, the control of fat globule agglomeration, the stabilisation of aerated systems and an improvement in the consistency of fat-based products.The use of rhaminolipids to improve the emulsifying properties of frozen desserts, butter and croissants has also been reported [4,111].For instance, Candida utilis produces a bioemulsifier used in processed salad dressings [160].A manoprotein produced by Saccharomyces cerevisi e stabilises water/oil emulsions in cookies, mayonnaise and ice cream, etc. [13,161].However, the food industry has not yet made widescale use of biosurfactants.Many of the properties of biosurfactants and their regulation as new ingredients for foods are pending approval.


Medicine

Biosurfactants have also been used in different biological (therapeutic) applications due to their fungicidal, bactericidal, insecticidal and anti-viral properties as well as use as anti-adhesive agents and enzyme inhibitors [111,116,117].A number of rhaminolipids exhibit antibacterial activity.For instance, Abalos et al. [162] identified six rhaminolipids in cultures of P. aeruginosa AT10 grown on soybean oil refinery residue and evaluated the antimicrobial properties of the solution.Thes

rhaminoli
ids exhibited excellent antifungal properties against different fungi at concentrations ranging from 16 to 32 µg/mL.C. bombicola-derived sophorolipids inhibited the growth of both Gram-negative and Gram-positive bacteria with a minimum inhibitory concentration of approximately 30 and 1 mg/mL in a contact time of 2 and 4 h, respectively, for E. coli (ATCC 8739) and P. aeruginosa (ATCC 9027) as well as 6 and 1 mg/mL in a contact time of 4 h for S. aureus (ATCC 6358) and B. subtilis (ATCC6633), respectively [163].

Despite the number of publications describing the antimicrobial activity of biosurfactants and patents related to their usage, real applications in the pharmaceutical, biomedical and health industries remains quite limited [164].Some lipopeptides, such as daptomycin, have reached a commercial antibiotic status [165].Daptomycin, is a branched cyclic lipopeptide isolated from Streptomyces roseosporus cultures and is produced by Cubist Pharmaceuticals under the name Cubicin ® [166].This drug was approved in 2003 for the treatment of skin infections caused by methicillin-resistant Staphylococcus aureus and other Gram-positive pathogens and approved in 2006 for the treatment of endocarditis and bacteraemia caused by S. aureus.Daptomycin had also been reported to display strong antibacterial activity against other important pathogens, such as penicillin-resistant Streptococcus pneumoniae, coagulase-negative Staphylococci, glycopeptide-intermediate-susceptible S. aureus and vancomycin-resistant Enterococci [166].

Biofilms are groups of bacteria and other organic matter that has colonised/accumulated on a given surface [117].Bacterial adherence to the surface is the first step in the establishment of biofilm and is affected by various factors, such as the type of microorganism, hydrophobicity, electrical charges of the surface, environmental conditions and the ability of microorganisms to produce extracellular polymers that assist the cells in anchoring to the surface [167].Anti-adherent activity, which is the ability to inhibit the adherence of pathogenic microorganisms to solid surfaces or infectious sites, has also been reported for biosurfactants, leading to a reduction in hospital infections with no need for drugs or synthetic chemical agents [112].Meylheuc et al. [168] studied a biosurfactant obtained from P. fluorescens with inhibitory properties regarding the adherence of Listeria monocytogenes to stainless steel and polytetrafluoroethylene surfaces.C. sphaerica-derived lunasan inhibited the adherence of P.aeruginosa, Streptococcus agalactiae and S. sanguis between 80% and 92% at a concentration of 10 mg/mL [95], while the biosurfactant rufisan produced by C. lipolytica UCP 0988 demonstrated antimicrobial activities against S. agalactiae, S. mutans, S. mutans NS, S. mutans HG, S. sanguis 12, S. oralis J22 at a concentration above the CMC (0.3%).Moreover, the biosurfactant showed anti-adherent activity against most of the microorganisms tested [137].

Deficiency of lung surfactant, which is a protein-phopholipid complex, is responsible for respiratory failure in premature infants.Gene isolation for protein molecules in this surfactant and cloning in bacteria allow fermentative production for medical applications [108].Sophorolipids from C. bombicola have been studied due to their spermicidal and cytotoxic activities as well as anti-HIV action that can reduce the proliferation of acquired immunodeficiency syndrome (AIDS).Sophorolipids have also been studied as nti-inflammatory agents for patients with immune diseases [108,169].Iturin is a lipopeptide produced by B. subtilis that has demonstrated antifungal activity by affecting the morphology and structure of the cell membrane of yeasts.In vitro experiments have demonstrated that surfactin can effectively inactivate the virus that causes herpes as well as the retrovirus and other compact RNA and DNA viruses.The antiviral activity of surfactin has been determined for a broad spectrum of viruses.Moreover, surfactin has been found to exert an effect on insulin absorption in the lungs of laboratory rats [108].


Nanaotechnology

Biosurfactants have been used in nanotechnology and nanoparticle synthesis is emerging as part of green chemistry [118,170].Nickel oxide (NiO) nano-rods can be produced by water-in-oil microemulsions [171].In one experiment, two microemulsions were formed with the addition of a nickel chloride solution to a biosurfactant and heptane solution, with the addition of ammonium hydroxide to the same hydrocarbon mixture.The centrifuged microemulsions and ethanol was then used to wash the precipitates and remo

the biosurfacta
t and heptane.The use of biosurfactants is a more ecofriendly approach [119].Reddy et al. [172] found that silver nanoparticle synthesis could be stabilised for two months using surfactin, which is a biodegradable, renewable stabilising agent with low toxicity [3,119].A biosurfactant produced by P. Aeruginosa grown in a low-cost medium has been employed to stabilise silver nanoparticles in the liquid phase [173].The effect of a rhamnolipid on the electrokinetic and rheological behaviour of nano-zirconia particles has also been analysed, although this is not strictly an environmental application [174].The biosurfactant increasingly adsorbs to zirconia with the increase in concentration and can serve as an ecofriendly product for the flocculation and dispersion of high solid contents of microparticles.New applications for biosurfactants are being developed in the field of nanotechnology.Future research should focus on the stabilisation of the nanoparticles by biosurfactants before addition during remediation processes [119].


Future Directions and Concluding Remarks

The biosurfactant industry has demonstrated remarkable growth in recent decades, although the large-scale production of these biomolecules remains a challenge from the economic standpoint.This is mainly due to the enormous difference between the financial investment required and viable industrial production.Thus, the following are the main criteria to be considered for biosurfactant production to become truly viable: (a) type of raw materials; (b) continuous provision of the same composi

on of ingredients; (c) types of microorga
isms; (d) the adequate design of industrial fermentors; (e) financial investments; (f) the target market; (g) purification processes; (h) biosurfactant properties; (i) production conditions, especially the time required for fermentation; (j) adequate production yields; and (k) the processing of recycled products (minimal or able to sell for more than the drop in value).

The target market is of fundamental importance to the implantation of an industrial biosurfactant production project.For cosmetic, medicinal and food products, production is only viable on a small-scale, as the column chromatography methods required to separate molecules are not economical on a large scale.Thus, the use of crude fermentation broths could be a viable solution, especially if the application is in an environmental context, as biosurfactants in such cases do not need to be pure and can be synthesized using a blend of i expensive carbon sources, which would allow the creation of an economically and environmentally viable technology for bioremediation processes.

According to Hazra et al. [140], sophorolipids are offered as sophoron TM from Saraya (Osaka, Japan) and Soliance (Pomacle, France), whereas rhamnolipids are available from Ecover (Boulogne-sur-Mer, France), Jeneil Biosurfactant Inc. (Saukville, Wisconsin, USA) and Rhamnolipid Holdings Inc. (New york, USA).Sophorolipid production costs run from 2 to 5 €/kg.Rhamnolipid production costs US$ 20/kg at a volume of 20 m 3 , but only US$ 5/kg when produced on a scale of 100 m 3 , placing it closer to ethoxylate or alkyl polyglycoside (US$ 1 to 3/kg).The Exxon Company spent more than US$ 10 million in bioremediation studies between 1993 and 1997 after the spillage of petroleum (41 million litres) by the oil tanker Exxon Valdez in Alaska in 1989, leading to the generation of seven patents and making bioremediation second only to enhanced oil recovery within the initial years of use.Distribution in specific biosurfactant areas of the oil industry includes 17 patents for soil and water bioremediation as well as 20 for enhanced oil recovery [140,175].

Although improvements in biosurfactant technology have enabled a 10-to-20-fold increase in the production of these biomolecules, it is likely that further, significant advances (even if of a smaller magnitude) are needed to make this technology commercially viable.

Figure 1 .
1
Figure 1.Surfactant molecule with apolar (hydrophobic) and polar (hydrophilic) moieties.


Figure 2 .
2
Figure 2. Schematic illustration of tensioactive agent and micelle formation.


Figure 3 .
3
Figure 3. Illustration of regions in which micelle formation occur (critical micelle concentration CMC).


Figure 1 .
1
Figure 1.Surfactant molecule with apolar (hydrophobic) and polar (hydrophilic) moieties.


Figure 1 .
1
Figure 1.Surfactant molecule with apolar (hydrophobic) and polar (hydrophilic) moieties.


Figure 2 .
2
Figu