Recent Progress in Photoelectrochemical Sensing of Pesticides in Food and Environmental Samples: Photoactive Materials and Signaling Mechanisms

Pesticides have become an integral part of modern agricultural practices, but their widespread use poses a significant threat to human health. As such, there is a pressing need to develop effective methods for detecting pesticides in food and environmental samples. Traditional chromatography methods and common rapid detection methods cannot satisfy accuracy, portability, long storage time, and solution stability at the same time. In recent years, photoelectrochemical (PEC) sensing technology has gained attention as a promising approach for detecting various pesticides due to its salient advantages, including high sensitivity, low cost, simple operation, fast response, and easy miniaturization, thus becoming a competitive candidate for real-time and on-site monitoring of pesticide levels. This review provides an overview of the recent advancements in PEC methods for pesticide detection and their applications in ensuring food and environmental safety, with a focus on the categories of photoactive materials, from single semiconductor to semiconductor–semiconductor heterojunction, and signaling mechanisms of PEC sensing platforms, including oxidation of pesticides, steric hindrance, generation/decrease in sacrificial agents, and introduction/release of photoactive materials. Additionally, this review will offer insights into future prospects and confrontations, thereby contributing novel perspectives to this evolving domain.


Introduction
Pesticides are a general term for chemicals for preventing, eliminating, and controlling diseases caused by pests, insects, and weeds [1].The application of pesticides significantly contributes to the advancement of agricultural production to meet the world's increasing population [2].Based on their effects, pesticides include several types, like herbicides, insecticides, fungicides, and rodenticides [3].According to their chemical structures, pesticides can be classified into carbamate, neonicotinoid, organophosphate, organochlorine, and pyrethroid [4].Most of the pesticides are hazardous, and their excessive or improper use may cause pesticide residue in crops, the atmosphere, soil, and water resources, posing a severe threat to the environmental system.Moreover, pesticide residue can enter the human body through the food chain to cause chronic or acute poisoning [5][6][7][8][9], manifesting as an increased risk of cancer, debilitating illnesses, and severe or even fatal symptoms [10][11][12][13][14].In recent years, pesticide residues have aroused global concern as a significant issue in environmental and food safety [15].Many countries have established policies in terms of their national conditions to stipulate the maximum residue limits of pesticides in agricultural products and acceptable daily intake from food [16,17].Therefore, effective detection of pesticides in food and environmental samples is a crucial step in implementing these policies and ensuring the health of human beings [18,19].
To date, a variety of methods have been developed for pesticide detection.Chromatography methods, including gas chromatography (GC) [20], high-performance liquid chromatography (HPLC) [21], and chromatography-mass spectrometry (LC-MS, HPLC-MS), exhibit high accuracy and sensitivity and are regarded as the gold standard detection approach to the analysis of pesticide residue levels [22,23].However, the demand for sophisticated and expensive instruments, laborious sample pretreatment, and professional operators limits their on-site application [24].Common rapid detection methods such as capillary electrophoresis [25], fluorescence [26], enzyme-linked immunosorbent assay [27], and surface-enhanced Raman scattering [28] have satisfactory sensitivity and selectivity but still suffer from short storage times and solution instability [19,29].As a consequence, there still need to be simple, low-cost, highly accurate, and sensitive methods for the sake of real-time and on-site monitoring of pesticide levels [30,31].
Photoelectrochemical (PEC) sensing is a newly emerged technique developed on the basis of electrochemical sensing via a systematic integration of light excitation and electrochemical analysis [32][33][34][35].By using electrochemical instruments to output signals, PEC sensing technology inherits the salient features of low cost, simple operation, fast response, capability of real-time monitoring, and easy miniaturization of instruments from the traditional electrochemical detection method [36][37][38].Moreover, due to the complete separation of light excitation and signal output, the PEC sensing method has much lower background signals than those of the conventional electrochemical method [39][40][41].Also, the strong redox ability of photogenerated charges reduces the dependence on the applied potential, thus endowing PEC sensing superior performance compared to electrochemical analysis [42].Owing to these advantages, PEC sensing has been widely used in many fields such as disease diagnosis [43][44][45], health monitoring [46][47][48], and medical science [49,50].Meanwhile, it meets the demand for rapid, convenient, sensitive, and accurate detection of pesticide residues in food and environmental samples [41,51,52].
Currently, several review reports have been published focusing on the advancement of PEC sensing technologies and their applications to multifarious target analytes [34][35][36][37]41].Nevertheless, an integral overview of PEC sensors concentrated on pesticide analysis for food and environmental safety is rare.We have witnessed inspiring progress in the PEC sensing of pesticides with high accuracy and sensitivity based on various efficient photoactive materials and flexible recognition mechanisms in recent years.Thus, this work presents a systematic and comprehensive review of the achievements in PEC sensing of pesticides.As displayed in Figure 1a, we intend to provide the readers with a clear view of the PEC sensors for pesticide detection, ranging from photoactive materials to signaling mechanisms.At the same time, the challenges and prospects in this area are also put forward.

Principles of the PEC Sensing System
A PEC sensing system converts light energy to electrical signals (Figure 1b), and its detection principle can be generally described as follows: Under illumination with higher energy than its band gap, the photoactive material on the photoelectrode absorbs photons and produces photogenerated electron-hole (e − -h + ) pairs.For n-type semiconductors, electrons in the conduction band (CB) migrate to the photoelectrode, while holes in the valence band (VB) are neutralized by an electron donor in the electrolyte, generating an anode photocurrent.For p-type semiconductors, electrons donated from the photoelectrode neutralize the holes in the VB, while CB electrons transfer to the electron acceptor in the electrolyte, producing a cathode photocurrent.When recognition elements in the PEC sensing system interact with the target analyte, the PEC response of the photoactive material changes and exhibits a certain correlation with the concentration of the analyte [53][54][55][56].There are two types of recognition elements for PEC sensing of pesticides: the first type includes aptamers, enzymes, and molecular imprinted polymers (MIPs), which are fixed on the photoelectrode surface of the photoactive materials via chemisorption, noncovalent/covalent binding, and affinity binding; the other type is the photoactive materials mobilized on the photoelectrode surface, which can directly react with pesticide to form a complex or cause a redox reaction.

Photoactive Materials
Photoactive material selection and material properties are key elements that impact the performance of the PEC sensor [57,58].Almost all the PEC sensing platforms for different analyte detections (e.g., biomolecule monitoring, antibiotic detection, pesticide sensing) follow the same principle: photoactive material with high e − -h + separation efficiency displays excellent PEC conversion ability, which will contribute to the high sensitivity of the PEC sensor [59,60].Up to now, various semiconductors with photoactivity have been developed and employed in the construction of PEC sensing systems.This section will provide an overview of the categories of photoactive materials, including single semiconductors and semiconductor-based heterojunctions, along with an introduction to their PEC properties, which is a precondition for developing effective strategies for the detection of pesticides.

Principles of the PEC Sensing System
A PEC sensing system converts light energy to electrical signals (Figure 1b), and its detection principle can be generally described as follows: Under illumination with higher energy than its band gap, the photoactive material on the photoelectrode absorbs photons and produces photogenerated electron-hole (e − -h + ) pairs.For n-type semiconductors, electrons in the conduction band (CB) migrate to the photoelectrode, while holes in the valence band (VB) are neutralized by an electron donor in the electrolyte, generating an anode photocurrent.For p-type semiconductors, electrons donated from the photoelectrode neutralize the holes in the VB, while CB electrons transfer to the electron acceptor in the electrolyte, producing a cathode photocurrent.When recognition elements in the PEC sensing system interact with the target analyte, the PEC response of the photoactive material changes and exhibits a certain correlation with the concentration of the analyte [53][54][55][56].There are two types of recognition elements for PEC sensing of pesticides: the first type includes aptamers, enzymes, and molecular imprinted polymers (MIPs), which are fixed on the photoelectrode surface of the photoactive materials via chemisorption, noncovalent/covalent binding, and affinity binding; the other type is the photoactive materials mobilized on the photoelectrode surface, which can directly react with pesticide to form a complex or cause a redox reaction.

Photoactive Materials
Photoactive material selection and material properties are key elements that impact the performance of the PEC sensor [57,58].Almost all the PEC sensing platforms for different analyte detections (e.g., biomolecule monitoring, antibiotic detection, pesticide sensing) follow the same principle: photoactive material with high e − -h + separation efficiency displays excellent PEC conversion ability, which will contribute to the high sensitivity of the PEC sensor [59,60].Up to now, various semiconductors with photoactivity have been developed and employed in the construction of PEC sensing systems.This section will provide an overview of the categories of photoactive materials, including single semiconductors and semiconductor-based heterojunctions, along with an introduction to their PEC properties, which is a precondition for developing effective strategies for the detection of pesticides.
In the early stages of the development of PEC sensing, classical single-component semiconductors were used as photoactive materials for the tentative exploration of PEC sensing technology.For example, a PEC sensing system for detecting acetylcholinesterase (AChE) activity and its inhibitor by employing CdS quantum dots (QDs) to construct the photoelectrode is one of the pioneering works in the history of PEC sensing [81].Afterwards, PEC sensors based on CdSe QDs, CdTe QDs, ruthenium bipyridyl derivatives, and porphyrin derivatives were used for the detection of several kinds of target analytes, including small biomolecules, cells, and heavy metal ions [66, [82][83][84].With the progress in material preparation and photoelectrode modification, other semiconductors were synthesized and applied for PEC sensing of pesticides.A PEC sensor based on polythiophene derivative film (PS 2 TTz) via a one-step electropolymerization process was constructed by Xu et al. [85], where PS 2 TTz serves both as a photoactive material and a recognition element for chlorpyrifos, displaying a detection range from 1 to 218.92 µg/L and a limit of detection (LOD) of 0.36 µg/L.Crossed BiOI nanoflake arrays were immobilized on an indium tin oxide (ITO) glass substrate via successive ionic layer adsorption and reaction approaches as a photocathode to detect methyl parathion, a model organophosphate pesticide [86].By coupling with AChE as the recognition element, the fabricated PEC system showed an LOD of 0.04 ng/mL and fine applicability for the detection of spiked food samples, including garlic, apple, and cabbage.Miao and coworkers investigated the effect of treatment temperature on the photocurrent response of BiVO 4 and reported a sensitive PEC biosensor for pesticide detection by using the ITO/BiVO 4 photoelectrode [87] (Figure 2a).Based on the best PEC performance obtained after the treatment at 300 • C, the PEC sensor could detect chlorpyrifos with an LOD of 0.25 pM and showed satisfactory recovery values for the analysis of spiked real-life samples, including grape, strawberry, spinach, and water samples.By calcination of Cu-benzene-1,3,5-tricarboxylic acid (Cu-BTC) MOF at 300 • C, a hierarchical CuO material was obtained and modified on an ITO electrode [88] (Figure 2b), possessing a high PEC conversion efficiency under visible-light irradiation.Based on the formation of the CuO-malathion complex, the as-prepared PEC sensor had an LOD of 8.6 × 10 −11 M and a successful application for the analysis of spiked Chinese cabbage samples.

Semiconductor-Based Heterojunctions
Despite some single-component photoactive materials that have been reported, the drawbacks of limited light-absorption ability, easy recombination of photogenerated e − -h + pairs, or serious photo-corrosion have impeded their PEC conversion efficiency and confined their practical application to a great extent [35,38,41].To improve the PEC properties of the photoactive materials and to enhance the performance of the PEC sensors, heterojunctions are favorable for the construction of PEC sensing systems.

Semiconductor-Based Heterojunctions
Despite some single-component photoactive materials that have been reported, the drawbacks of limited light-absorption ability, easy recombination of photogenerated e − -h + pairs, or serious photo-corrosion have impeded their PEC conversion efficiency and confined their practical application to a great extent [35,38,41].To improve the PEC properties of the photoactive materials and to enhance the performance of the PEC sensors, heterojunctions are favorable for the construction of PEC sensing systems.

Semiconductor-Semiconductor Heterojunction
It has been considered an effective approach to constructing heterostructures based on two semiconductors with different band gaps to acquire photoelectrodes with the desired PEC properties [29].The most typical heterojunction used in PEC sensing is composed of two kinds of inorganic semiconductors with suitable energy levels for e − -h + pair separation.TiO2 is one of the classical photoactive materials used in PEC sensing due to its good biocompatibility and photochemical stability [89].However, its wide band gap results in limited excitation only under UV light, which is known for harming biological substances and having a low proportion in natural light [90,91].Zhou and coworkers synthesized a nanocomposite of g-C3N4 and TiO2 nanotube arrays (TNA/g-C3N4) by in situ generating g-C3N4 on the surface of TNA [92].Due to the relatively narrow band gap of g-C3N4 and the suitable energy level matching between TNA and g-C3N4, TNA/g-C3N4 showed a photocurrent response in the visible-light region.By utilizing TNA/g-C3N4 as a photoelectrode, a PEC sensor for acetamiprid detection was fabricated with the combination of λ exonuclease-assisted recycling amplification and DNAzyme-catalyzed precipitation, showing a low LOD of 0.025 pM and application for the analysis of spiked tomato, cucumber, and bitter gourd samples.Lyu and coworkers developed an n-n heterojunction by immobilizing BiOI on the surface of TiO2, which had a heterophase junction of anatase/rutile (AR-TiO2) [93] (Figure 3a).The different functions of AR-TiO2 built an internal electric field to promote carrier transfer across the heterophase, and the three-dimensional BiOI had a loose porous structure consisting of abundant small and thin nanosheets, which contributed to enhanced light absorption and separation of photogenerated e − -h + pairs.The PEC sensor showed good performance toward detecting chlorpyrifos with an LOD of 0.24 pg/mL and a potential application value for detecting spiked lettuce, pitaya, and water samples.Bi2S3@g-C3N4, a p-n heterojunction photoactive composite, was prepared by Lei et al. to promote charge transfer and suppress e − -h + pair recombination [94].The obtained Bi2S3@g-C3N4/ITO photoelectrode was used to detect chlorpyrifos based on the affinity between chlorpyrifos and the Bi (III) surface, presenting a linear range from

Semiconductor-Semiconductor Heterojunction
It has been considered an effective approach to constructing heterostructures based on two semiconductors with different band gaps to acquire photoelectrodes with the desired PEC properties [29].The most typical heterojunction used in PEC sensing is composed of two kinds of inorganic semiconductors with suitable energy levels for e − -h + pair separation.TiO 2 is one of the classical photoactive materials used in PEC sensing due to its good biocompatibility and photochemical stability [89].However, its wide band gap results in limited excitation only under UV light, which is known for harming biological substances and having a low proportion in natural light [90,91].Zhou and coworkers synthesized a nanocomposite of g-C 3 N 4 and TiO 2 nanotube arrays (TNA/g-C 3 N 4 ) by in situ generating g-C 3 N 4 on the surface of TNA [92].Due to the relatively narrow band gap of g-C 3 N 4 and the suitable energy level matching between TNA and g-C 3 N 4 , TNA/g-C 3 N 4 showed a photocurrent response in the visible-light region.By utilizing TNA/g-C 3 N 4 as a photoelectrode, a PEC sensor for acetamiprid detection was fabricated with the combination of λ exonuclease-assisted recycling amplification and DNAzyme-catalyzed precipitation, showing a low LOD of 0.025 pM and application for the analysis of spiked tomato, cucumber, and bitter gourd samples.Lyu and coworkers developed an n-n heterojunction by immobilizing BiOI on the surface of TiO 2 , which had a heterophase junction of anatase/rutile (AR-TiO 2 ) [93] (Figure 3a).The different functions of AR-TiO 2 built an internal electric field to promote carrier transfer across the heterophase, and the three-dimensional BiOI had a loose porous structure consisting of abundant small and thin nanosheets, which contributed to enhanced light absorption and separation of photogenerated e − -h + pairs.The PEC sensor showed good performance toward detecting chlorpyrifos with an LOD of 0.24 pg/mL and a potential application value for detecting spiked lettuce, pitaya, and water samples.Bi 2 S 3 @g-C 3 N 4 , a p-n heterojunction photoactive composite, was prepared by Lei et al. to promote charge transfer and suppress e − -h + pair recombination [94].The obtained Bi 2 S 3 @g-C 3 N 4 /ITO photoelectrode was used to detect chlorpyrifos based on the affinity between chlorpyrifos and the Bi (III) surface, presenting a linear range from 50 ng/mL to 0.1 mg/mL and an LOD of 0.03 ng/mL.Furthermore, the novel PEC sensing platform could support fast and effective monitoring of spiked green vegetable samples.
Organic molecule-based photovoltaic materials have attracted much attention for their high visible-light absorption, precise molecular structures, and controllable assembling process.Therefore, the organic-inorganic heterojunction can lay a solid foundation for PEC sensing and pesticide detection.Poly(3-hexylthiophene) (P3HT) is one of the excellent photoelectric materials with high charge carrier mobility and strong absorption in the visible region [95].Hu's group used P3HT as a sensitizer of TiO 2 to prepare P3HT/TiO 2 nanocomposites for the PEC detection of chlorpyrifos [96].Later, they reported a TiO 2 -P3HT-ionic liquid (IL) nanocomposite film by blending TiO 2 nanoparticles (NPs) and P3HT at room temperature IL [97].The improved ionic conductivity resulted from IL was beneficial for promoted charge transfer and higher PEC efficiency, and the proposed PEC sensor could detect acetochlor with an LOD of 0.2 nM.The results of spiked water samples were in acceptable agreement with those of the GC-MS method.Song and coworkers synthesized a di-branched di-anchoring dye, T(TA) 2 , to sensitize TiO 2 NPs for the highly sensitive PEC sensing of organophosphate pesticides [98] (Figure 3b).The unique D-(π-A) 2 structure endows the T(TA) 2-TiO 2 nanocomposites with higher PEC conversion efficiency and superior photo-stability in aqueous solutions, even better than two kinds of organic dye-sensitized TiO 2 nanocomposites mostly used in DSSCs or PEC sensing fields.The PEC sensor showed a wide linear range of 2 × 10 −12 -4 × 10 −6 g/mL, a low LOD of 5.6 × 10 −13 g/mL, and acceptable accuracy for the detection of spiked apple juice samples.
platform could support fast and effective monitoring of spiked green vegetable samples.
Organic molecule-based photovoltaic materials have attracted much attention for their high visible-light absorption, precise molecular structures, and controllable assembling process.Therefore, the organic-inorganic heterojunction can lay a solid foundation for PEC sensing and pesticide detection.Poly(3-hexylthiophene) (P3HT) is one of the excellent photoelectric materials with high charge carrier mobility and strong absorption in the visible region [95].Hu's group used P3HT as a sensitizer of TiO2 to prepare P3HT/TiO2 nanocomposites for the PEC detection of chlorpyrifos [96].Later, they reported a TiO2-P3HT-ionic liquid (IL) nanocomposite film by blending TiO2 nanoparticles (NPs) and P3HT at room temperature IL [97].The improved ionic conductivity resulted from IL was beneficial for promoted charge transfer and higher PEC efficiency, and the proposed PEC sensor could detect acetochlor with an LOD of 0.2 nM.The results of spiked water samples were in acceptable agreement with those of the GC-MS method.Song and coworkers synthesized a di-branched di-anchoring dye, T(TA)2, to sensitize TiO2 NPs for the highly sensitive PEC sensing of organophosphate pesticides [98] (Figure 3b).The unique D-(π-A)2 structure endows the T(TA)2-TiO2 nanocomposites with higher PEC conversion efficiency and superior photo-stability in aqueous solutions, even better than two kinds of organic dye-sensitized TiO2 nanocomposites mostly used in DSSCs or PEC sensing fields.The PEC sensor showed a wide linear range of 2 × 10 −12 -4 × 10 −6 g/mL, a low LOD of 5.6 × 10 −13 g/mL, and acceptable accuracy for the detection of spiked apple juice samples.

Semiconductor-Carbon Heterojunction
Carbon-based materials have diverse electronic structures of C elements (sp, sp 2 , and sp 3 hybridization) and various nanostructures, including nanosheets (NSs), nanofibers

Semiconductor-Carbon Heterojunction
Carbon-based materials have diverse electronic structures of C elements (sp, sp 2 , and sp 3 hybridization) and various nanostructures, including nanosheets (NSs), nanofibers (NFs), and nanotubes (NTs) [101][102][103].Due to their inherent merits, such as good chemical stability, fast electron mobility, excellent biocompatibility, and large specific surface area, carbon materials have been extensively employed for coupling with semiconductors to obtain heterojunctions for developing PEC sensors.They are usually considered ideal electron transfer media to accelerate the transfer of photogenerated electrons and promote the separation of e − -h + pairs [38,41].Additionally, a large surface area can also provide abundant active sites to absorb electroactive species and biomolecules via covalent bonding, π-π packing, and hydrogen bonding [104].Therefore, semiconductor-carbon heterojunc-tion usually contributes to the better PEC properties of photoactive materials and endows PEC sensors with superior performance.
Graphene (GR) and reduced graphene oxide (RGO) are the most common carbon materials used for constructing semiconductor-carbon heterojunctions in PEC sensing of pesticides.BiPO 4 -functionalized RGO nanocomposites (BiPO 4 -RGO) were synthesized and showed enhanced PEC response compared with the pure BiPO 4 NPs.Because the photogenerated electrons can be stored by RGO NSs, the accelerated electron transfer reduced the recombination rate of the photogenerated e − -h + pairs [105].The as-developed PEC sensor for chlorpyrifos detection exhibited a broad linear range from 0.05 to 80 ng/mL, a low LOD of 0.02 ng/mL, and satisfactory results according to the determination of spiked wastewater samples.Ding and coworkers fabricated a MoTe 2 NPs/RGO heterostructure via a one-step hydrothermal synthesis process [99] (Figure 3c).Due to the suitable Schottky barrier, the obtained heterostructure exhibited a photocurrent intensity of 21.8 times that of RGO and 10.5 times that of MoTe 2 NPs, respectively.Then, a label-free PEC aptasensor was successfully constructed to determine profenofos in concentrations ranging from 10 −9 to 10 −2 g/L with an LOD of 3.3 × 10 −10 g/L and was successfully conducted in spiked vegetable samples.p-type BiOBr nanoplates decorated with n-type N-doped GR (BiOBr-NGR) composites were prepared to construct a p-n heterojunction for the separation of photogenerated e − -h + pairs and enhanced PEC response [106].Based on the improved photocurrent signal, a PEC sensor was developed for the detection of chlorpyrifos, presenting a low LOD of 1.67 pg/mL and offering a general approach to chlorpyrifos detection in food and environmental samples.Yan and coworkers fabricated a thiophenesulfur-doped GR/ZnO nanocomposite (t-SG/ZnO) [100] (Figure 3d), where the t-SG/ZnO had a narrower band gap, stronger visible-light absorption, and better photo-stability than that of the pure ZnO nanoplates because of the facilitated interfacial charge transfer.Meanwhile, t-SG/ZnO also exhibited a PEC response of about 1.5 times and 2.6 times that of N-doped GR/ZnO and GR/ZnO, respectively.On this basis, an "on-off-on" PEC aptasensor was constructed for the detection of acetamiprid, showing an LOD of 0.33 ng/mL and analytical applicability for the detection of spiked cucumber samples.

Semiconductor-Noble Metal Heterojunction
Noble metals, including gold, silver, and platinum, have excellent conductivity and strong electron trapping abilities, so they can serve as electron traps to accelerate the transportation of charge carriers and suppress the recombination of the photogenerated e − -h + pairs [107][108][109].Generally, there are two possible paths for the electron transfer in a semiconductor-noble metal heterojunction [110]: in one situation, the photoexcited electrons from the semiconductor will transfer to the noble metals, forming an energy transfer process; in the other situation, when the heterojunction is composed of nanostructured noble metal and wide band gap semiconductor, hot electrons induced by the surface plasmon resonance (SPR) effect will transfer from the noble metal to the semiconductor, along with enhanced visible-light absorption at the same time.
Recently, Au NPs have been frequently coupled with nanostructured TiO 2 to establish PEC sensing systems for pesticide detection.A PEC aptasensor was fabricated for the detection of diazinon by using Au NPs/TiO 2 nanocomposite as the photoactive material [111].The use of Au NPs not only improved the PEC properties of the Au NPs/TiO 2 nanocomposite with a higher photocurrent response compared to the pure TiO 2 , but also provided active sites for the aptamer conjugating to the Au NPs/TiO 2 through S-Au bonds.The as-fabricated PEC sensor showed high sensitivity, selectivity, reproducibility, and stability for the quantitative determination of diazinon and obtained satisfactory results for the detection of diazinon in water and biological samples.Zhang and coworkers developed a PEC sensing platform based on Au NPs modified with a three-dimensionally ordered macroporous (3DOM) TiO 2 nanostructure frame for trace detection of atrazine [112] (Figure 4a).Owing to multi-signal amplification of the 3DOM structure of TiO 2 and the SPR effect of Au NPs, the Au NPs/3DOM TiO 2 photoanode showed improved PEC performance under visible light.Meanwhile, its orderly nanostructure contributed to a large packing density of aptamers by Au-S bond with dominant spatial orientation for the specific recognition of atrazine, thus providing the PEC aptasensor with a low LOD of 0.167 ng/L and a great application prospect based on analysis of real water samples.Besides Au NPs, Pd NPs are another plasmonic nanostructured noble metal used to construct semiconductor-noble metal heterojunctions for pesticide determination.Wen and coworkers prepared Pd NPs decorated CdS microsphere (Pd NPs/CdS) for the PEC aptasensing of carbendazim [113] (Figure 4b).Based on the SPR effect of Pd NPs and the Schottky junction between Pd NPs and the CdS microsphere, the photocurrent obtained from Pd NPs/CdS was 7.7 times higher than that of the bare CdS microsphere.The as-fabricated PEC aptasensor possessed excellent performance with a wide linear range of 1.0 × 10 −12 -1.0 × 10 −6 M and a low LOD of 3.3 × 10 −13 M. Furthermore, the PEC aptasensor was employed for the analysis of spiked lettuce samples with satisfactory results.
The as-fabricated PEC sensor showed high sensitivity, selectivity, reproducibility, and stability for the quantitative determination of diazinon and obtained satisfactory results for the detection of diazinon in water and biological samples.Zhang and coworkers developed a PEC sensing platform based on Au NPs modified with a three-dimensionally ordered macroporous (3DOM) TiO2 nanostructure frame for trace detection of atrazine [112] (Figure 4a).Owing to multi-signal amplification of the 3DOM structure of TiO2 and the SPR effect of Au NPs, the Au NPs/3DOM TiO2 photoanode showed improved PEC performance under visible light.Meanwhile, its orderly nanostructure contributed to a large packing density of aptamers by Au-S bond with dominant spatial orientation for the specific recognition of atrazine, thus providing the PEC aptasensor with a low LOD of 0.167 ng/L and a great application prospect based on analysis of real water samples.Besides Au NPs, Pd NPs are another plasmonic nanostructured noble metal used to construct semiconductor-noble metal heterojunctions for pesticide determination.Wen and coworkers prepared Pd NPs decorated CdS microsphere (Pd NPs/CdS) for the PEC aptasensing of carbendazim [113] (Figure 4b).Based on the SPR effect of Pd NPs and the Schottky junction between Pd NPs and the CdS microsphere, the photocurrent obtained from Pd NPs/CdS was 7.7 times higher than that of the bare CdS microsphere.The as-fabricated PEC aptasensor possessed excellent performance with a wide linear range of 1.0 × 10 −12 -1.0 × 10 −6 M and a low LOD of 3.3 × 10 −13 M. Furthermore, the PEC aptasensor was employed for the analysis of spiked lettuce samples with satisfactory results.

Multicomponent Heterojunction
A multicomponent heterojunction is composed of semiconductors, carbon materials, or noble metals with more than two components.It involves interactions between several materials and usually consists of more than one heterojunction, thus combining the advantages of different types of heterojunctions and providing the opportunity to elaborately match the band levels of each semiconductor for an optimized electron transfer path [36].For example, a TiO2/S-BiVO4@Ag2S heterojunction with cascade band-edge levels can accelerate charge transfer and promote separation of the charge carriers effectively, presenting a photocurrent intensity about 2.1 times higher than that obtained from the TiO2/S-

Multicomponent Heterojunction
A multicomponent heterojunction is composed of semiconductors, carbon materials, or noble metals with more than two components.It involves interactions between several materials and usually consists of more than one heterojunction, thus combining the advantages of different types of heterojunctions and providing the opportunity to elaborately match the band levels of each semiconductor for an optimized electron transfer path [36].For example, a TiO 2 /S-BiVO 4 @Ag 2 S heterojunction with cascade band-edge levels can accelerate charge transfer and promote separation of the charge carriers effectively, presenting a photocurrent intensity about 2.1 times higher than that obtained from the TiO 2 /S-BiVO 4 electrode [116].A CuO/Pd NPs nanocomposite coupled with CdS QDs can exhibit a synergistic effect through Schottky junction and sensitization, therefore suppressing efficient charge recombination and light absorption to a great extent [117].
Recently, considerable efforts have been devoted to designing and constructing multicomponent heterojunctions for PEC sensing of pesticides.Zhou and coworkers prepared a BiOI-Bi/short carbon nanotubes (BiOI-Bi/s-CNTs) composite that contained a semiconductor-metal heterojunction and a semiconductor-carbon heterojunction [118].An intensive photocurrent response was achieved due to the active SPR effect of Bi NPs and the high charge mobility of s-CNTs, and the PEC sensor was established for chlorpyrifos detection, showing an LOD of 1.89 pg/mL and satisfactory recoveries of chlorpyrifos in spiked cabbage and Chinese cabbage samples.A PEC aptasensor for carbendazim detection was constructed based on the CdTe-polyaniline@MoS 2 heterostructure [114] (Figure 4c).The cascade Z-scheme electron transfer resulted in a significantly increased photocurrent, which was 2.7-fold higher than that at CdTe/MoS 2 for the facilitated separation of photogenerated e − -h + pairs.The fabricated PEC aptasensor possessed a linear range of 0.1-100 ng/mL with an LOD of 0.033 ng/mL, and it was successfully applied for spiked tomato sample analysis.Zheng and coworkers synthesized a porous hollow CdCoS 2 (2) microsphere consisting of a CdS-CoS heterojunction with well-matched energy bands and outstanding PEC properties, which was further improved by compositing CdCoS 2 (2) with the conductive Ag NPs [115] (Figure 4d).The PEC sensor was used to monitor chlorpyrifos based on its inhibition effect on AChE and achieved a wide linear response range (0.001 to 270 µg/mL), a low LOD (0.57 ng/mL), and successful application for the chlorpyrifos determination in spiked river water samples.

Signaling Mechanisms
Almost all PEC sensors achieve selective detection of the target based on specific recognition between the target and the recognition element.As an important application area of PEC sensing, PEC sensors for pesticide detection share common recognition element categories and signaling transduction strategies with PEC sensing platforms for the detection of other small molecules.For pesticide detection, recognition elements include aptamers [92], enzymes [98,115], MIPs [119], and photoactive materials [88,93], and their chemical compositions and molecular structures are usually selected or designed according to the specific target pesticides.The reactions between the recognition element and the target pesticide will subsequently trigger physical or chemical reactions and cause the photocurrent change of the PEC sensor via a series of signaling mechanisms.This section will provide an overview of the signaling mechanisms for PEC sensing of pesticides, which are important for the design of recognition strategies for the PEC sensors.

Oxidation of Pesticide
During the PEC sensing process, photoactive materials are excited under illumination to generate e − -h + pairs, and the holes with strong oxidative power can directly oxidize some target pesticides or oxidize some hole mediators to form free radical moieties, which further induce the oxidation of the target pesticides.Such interaction between the photogenerated holes and the pesticides is beneficial for the neutralization of the holes and the separation of the photogenerated e − -h + pairs, thus improving the PEC conversion efficiency and enhancing the photocurrent response [120].
Wang and coworkers fabricated a PEC sensor based on Au NPs and poly(o-phenylenediamine) (PoPD)-modified TiO 2 NTs for the detection of lindane [119].PoPD not only served as an MIP to specifically capture lindane molecules but also acted as a photoactive material to generate charge carriers under visible-light excitation.The electrons transferred from the lowest unoccupied molecular orbital of PoPD to the CB of the TiO 2 NTs, while the holes of PoPD were consumed by taking part in the oxidation of the lindane, promoting the separation of the photogenerated e − -h + pairs and the amplification of the photocurrent response.A similar work was proposed by the same research group for the PEC sensing of chlorpyrifos, in which a PoPD-AuNPs/TiO 2 NTs composite was proposed by using Au NPs to improve the interfacial charge transfer efficiency [121].Based on the oxidation of the chlorpyrifos by photogenerated holes, the photocurrent increased proportionally to chlorpyrifos levels ranging from 0.05 to 10 µM, with an LOD of 0.96 nM.Furthermore, the PEC sensor was successfully applied to the determination of spiked green vegetables.
When a hole mediator exists in the PEC sensing system, it can be oxidized by the photogenerated holes to form free radicals with superior oxidative abilities, which can subsequently oxidize the pesticides.H 2 O is the most commonly used hole mediator, as PEC sensing measurements are often carried out in aqueous solutions.For example, a PEC sensor for chlor-pyrifos determination was fabricated based on a 1D TiO 2−x /3D nitrogen-doped graphene hydrogel (NGH) heterostructure [122].Under light excitation, the photogenerated holes were clustered on the VB of TiO 2 and could oxidize H 2 O to produce hydroxyl radicals (•OH).Then, •OH and holes induced the oxidation of chlorpyrifos, leading to an amplified photocurrent response.The constructed PEC sensor possessed high reliability and accuracy for chlorpyrifos detection and exhibited good performance for practical determination in wastewater samples.Wen and coworkers developed a PEC sensing platform by employing Blue-TiO 2 (B-TiO 2 ) and N-hydroxyphthalimide (NHPI) as the photoactive material and the hole mediator, respectively [123] (Figure 5a).Photogenerated holes transferred from the VB of B-TiO 2 to NHPI and oxidized NHPI to phthalimide-N-oxyl radical, which could oxidize the diazinon captured by the aptamer immobilized on the photoelectrode surface.The as-fabricated PEC aptasensor exhibited a linear range for diazinon detection from 0.1 to 1000 nM with an LOD of 0.03 nM and showed food recovery results for spiked apple samples.

Steric Hindrance
Steric hindrance resulting from molecular recognition reactions is another signaling strategy in the construction of PEC sensing platforms.For pesticide detection, the common recognition reactions consist of biocatalytic precipitation and binding interactions between the pesticide and the recognition elements.The introduction of steric hindrance may lead to diffusion suppression of electron donor/acceptor to photogenerated carriers and transfer inhibition of the photogenerated carriers to the photoactive materials, thereby resulting in a significant decrease in photocurrent response [55].
Biocatalytic precipitation (BCP) is an effective approach to inducing steric hindrance to the PEC sensing systems.Horseradish peroxidase (HRP) can facilitate the oxidation of 4-chloro-1-naphthol (4-CN) by H 2 O 2 to generate benzo-4-chlorohexadienone (4-CD), an insoluble and insulating precipitate, on photoelectrode surfaces [124].Based on this principle, some DNAzymes or nanozymes have been designed to simulate the activity of HRP for a BCP reaction [92,[125][126][127].Zhou and coworkers developed a PEC aptasensor for acetamiprid detection.Combining aptasensing and λ exonuclease-assisted recycling amplification, an HRP-mimicking hemin/G-quadruplex DNAzyme formed and biocatalytically oxidized 4-CN to generate 4-CD, inhibiting electron donor diffusion to the surface of the photoanode and reducing the photocurrent response [92].A PEC aptasensor was constructed by using CeO 2 -Au nanozyme as a signal amplification platform to conduct a BCP reaction and quench the photocurrent signals [127] (Figure 5b).The recognition of target acetamiprid caused the release of CeO 2 -Au from the photoelectrode, thus weakening the quenching effect and recovering the photocurrent signal.The obtained PEC aptasensor exhibited an LOD of 0.05 pM over a linear range of 0.1 pM-10 µM acetamiprid and a high acetamiprid detection accuracy in spiked cucumber samples.
The specific binding of the recognition element to the pesticide is another strategy to form steric hindrance on the photoelectrode surface.For example, when a target pesticide is captured by its aptamer, or MIP, the formation of an aptamer-pesticide complex or MIP-pesticide complex will increase the steric hindrance and decrease the conductivity for electron transfer [128][129][130][131][132][133][134].A PEC sensor was constructed by Cao and coworkers based on a hierarchically porous Cu-BTC/g-C 3 N 4 nanosheet (Cu-BTC/CN-NS) as both a photoactive material and the recognition element for glyphosate [135] (Figure 5c).During the PEC sensing process, the Cu metal center coordinated with glyphosate to form Cu-glyphosate complexes, resulting in an increased steric hindrance to block electron transfer and an obvious decrease in photocurrent.The constructed PEC sensor can achieve the detection of glyphosate with a low LOD (1.3 × 10 −13 M) and a wide detection range (1.0 × 10 −12 -1.0 × 10 −8 M and 1.0 × 10 −8 -1.0 × 10 −3 M), and it also showed great analytical performance in PEC sensing of glyphosate in spiked soybean samples.A similar strategy was utilized for the PEC sensing of malathion, exhibiting high sensitivity and potential application in reallife sample analysis [88].Besides Cu-containing photoactive materials, some photoactive materials, including Bi and Co-based semiconductors, can also form similar photoactive material-pesticide complexes, which contribute to increased steric hindrance, suppressed charge transfer, and reduced photocurrent response [93,105,106,[135][136][137][138][139][140][141].
For PEC sensing platforms based on the steric hindrance strategy, the conductivity of the photoelectrode interface decreases as the pesticide concentration increases.Meanwhile, long operation times might promote the formation of recognition element-target pesticide complexes and contribute to the steric hindrance.To achieve high sensitivity, some researchers optimized the incubation or adsorption time until the binding reactions reached saturation [128,131].As the steric hindrance is caused by the formation of recognition element-target pesticide complexes, most of the sensing photoelectrodes are not reusable due to the irreversible binding reactions between the recognition elements and the target pesticides.Only some PEC sensors using MIPs as recognition elements mentioned that the molecularly imprinted electrode could be reused several times by eluting the templates to regenerate the MIPs [132,142,143].

Generation/Decrease in Sacrificial Agents
Regulating the generation of the sacrificial agents is a straightforward approach to designing the signaling strategy of a PEC sensor.On one hand, the in situ generated electron donor/acceptor can react with excited holes/electrons, thus suppressing the recombination of the photogenerated e − -h + pairs to obtain increased and stable photocurrent signals [37].A simple example is the hydrolyzation of parathion-methyl in alkaline conditions, and the hydrolysate, p-nitrophenol, which served as the electron donor, is oxidized by the holes to amplify the photocurrent response [144,145].On the other hand, the inhibition of the generation of sacrificial agents will in turn decline the PEC signal.
Enzymatic reactions are commonly utilized to establish the signaling mechanism for the PEC sensing of organophosphate pesticides.AChE is a typical enzyme used in a PEC sensor for pesticide detection due to the catalytical hydrolysis of acetylthiocholine (ATCh) to generate thiocholine (TCh) as electron donors, resulting in an enhanced photocurrent response [98].Organophosphate pesticides can inhibit the bioactivity of AChE, and the photocurrent signal will decrease due to the reduced production of TCh [115].Upon this method, some PEC sensing platforms for organophosphate pesticides have been developed by collaborating photoactive materials with high PEC conversion efficiency [98,115,146,147].For example, a self-powered PEC sensor based on ZnO nanorod/3D graphene aerogel-sensitized structure and inhibition effects of parathion-methyl on AChE was fabricated (Figure 5d), showing the detection of parathion-methyl with a linear range of 0.1 ng/mL to 0.1 µg/mL and a LOD of 0.03 ng/mL.Cheng and coworkers proposed a visible-light-driven and self-powered PEC sensor based on AChE-immobilized N-doped carbon QDs/TiO 2 /ITO photoelectrode [147], which can achieve the detection of chlorpyrifos with high sensitivity (a LOD of 0.07 ng/mL), board detection range (0.001-1.5 µg/mL), and accurate determination of spiked lake water and Chinese cabbage samples.It should be noticed that once removed from the pesticide solution, the AChE-modified photoelectrodes cannot regain their enzymatic activity due to the irreversible inhibition of pesticides, and thus the photoelectrodes are single-use items in theory.The inhibited AChE can be reactivated when using nucleophilic compounds such as pralidoxime iodide.For example, Du and coworkers have observed that an AChE-modified electrode inhibited by malathion could recover more than 90% of its original activity after immersing in a pralidoxime iodide solution for several minutes [148], which might be helpful to obtain reusable photoelectrodes.Apart from AChE, other enzymes, including alkaline phosphatase and glucose oxidase, have been employed on account of the catalytical hydrolysis of their substrates to in situ generate ascorbic acid and H 2 O 2 , serving as electron donors to enhance the PEC conversion efficiency and amplify the photocurrent response [149,150].malathion could recover more than 90% of its original activity after immersing in a pralidoxime iodide solution for several minutes [148], which might be helpful to obtain reusable photoelectrodes.Apart from AChE, other enzymes, including alkaline phosphatase and glucose oxidase, have been employed on account of the catalytical hydrolysis of their substrates to in situ generate ascorbic acid and H2O2, serving as electron donors to enhance the PEC conversion efficiency and amplify the photocurrent response [149,150].

Introduction/Release of Photoactive Materials
The introduction/release of photoactive species is an effective method for PEC signaling.By using the recognition event to introduce/release the photoactive materials on/from the photoelectrode, the PEC properties, including light absorption properties, e −h + generation, and charge transfer, can be regulated, thereby leading to the change of PEC signals [37,38].
Zeng and coworkers reported a signal-on PEC sensor to determine malathion based on the in situ formation of DNA-templated Ag2S photoactive materials [151] (Figure 6a).The target-induced hybridization chain reaction (HCR) caused the exposure of rich "C" strands to assemble multiple silver ions by C-Ag + -C chelation.Afterwards, the Ag2S was generated in situ through the reaction between S 2− and Ag + ions, presenting a desirable PEC signal.This signaling strategy dispensed with the pre-synthesis or immobilization of the photoactive materials, so it had nearly zero background noise, which was desirable for a high sensitivity with an LOD of 2 pg/mL.Meanwhile, the PEC sensor was also successfully applied to detect malathion in real samples.In another work, a target (malathion)-induced HCR can produce a long DNA concatemer containing the sequence of the

Introduction/Release of Photoactive Materials
The introduction/release of photoactive species is an effective method for PEC signaling.By using the recognition event to introduce/release the photoactive materials on/from the photoelectrode, the PEC properties, including light absorption properties, e − -h + generation, and charge transfer, can be regulated, thereby leading to the change of PEC signals [37,38].
Zeng and coworkers reported a signal-on PEC sensor to determine malathion based on the in situ formation of DNA-templated Ag 2 S photoactive materials [151] (Figure 6a).The target-induced hybridization chain reaction (HCR) caused the exposure of rich "C" strands to assemble multiple silver ions by C-Ag + -C chelation.Afterwards, the Ag 2 S was generated in situ through the reaction between S 2− and Ag + ions, presenting a desirable PEC signal.This signaling strategy dispensed with the pre-synthesis or immobilization of the photoactive materials, so it had nearly zero background noise, which was desirable for a high sensitivity with an LOD of 2 pg/mL.Meanwhile, the PEC sensor was also successfully applied to detect malathion in real samples.In another work, a target (malathion)-induced HCR can produce a long DNA concatemer containing the sequence of the G-quadruplex structure, then obtain HRP-like activity via the formation of hemin/G-quadruplex complexes and binding with manganese porphyrin [152].With the aid of H 2 O 2 , the HRP-mimicking DNA concatemer catalyzed S 2 O 3 2− to generate S 2− , which could react with BiOBr nanoflowers to in situ form a BiOBr/Bi 2 S 3 heterostructures with enhanced PEC conversion efficiency.The proposed PEC sensor achieved a wide linear range of 0.001-1000 ng/mL and an LOD of 0.12 pg/mL for malathion determination, and its application potential was verified by using it for the detection of spiked milk samples.
Inhibiting the generation of photoactive materials or releasing photoactive materials from the photoelectrode will result in a drop in the PEC signal.For example, a PEC sensor for asulam detection was developed based on the inhibitory effect on HRP enzyme activity and the lower production of S 2− from the conversion of S 2 O 3 2− [153] (Figure 6b).Consequently, the amount of in situ-generated CdS reduced, and the photocurrent decreased with the concentration of asulam in a range from 0.02 to 2.0 ng/mL.The PEC sensor showed an LOD of 4.1 pg/mL and good accuracy in the analysis of spiked environmental water samples.Qin and coworkers proposed a PEC sensing platform for paraoxon detection by using a dissociable photoelectrode based on CdS nanocrystal-functionalized MnO 2 NSs [154].TCh can effectively etch MnO 2 NSs, causing the dissociation of MnO 2 -CdS from the photoelectrode and the decline of the photocurrent response.With the presence of organophosphate pesticides, the generation of TCh and the dissociation of MnO 2 NSs were prevented due to the inhibition of AChE, thus recovering the PEC signals.Upon this signaling strategy, rolling circle amplification was introduced to assemble a large number of butyrylcholinesterase (BChE) for increased production of TCh and promoted dissociation of MnO 2 -CdS [155].Based on the inhibition of BChE by malathion, the PEC sensor possessed high sensitivity for malathion with a low LOD of 0.68 pg/mL and favorable accuracy in the analysis of spiked red wine and milk samples.
G-quadruplex structure, then obtain HRP-like activity via the formation of hemin/Gquadruplex complexes and binding with manganese porphyrin [152].With the aid of H2O2, the HRP-mimicking DNA concatemer catalyzed S2O3 2− to generate S 2− , which could react with BiOBr nanoflowers to in situ form a BiOBr/Bi2S3 heterostructures with enhanced PEC conversion efficiency.The proposed PEC sensor achieved a wide linear range of 0.001-1000 ng/mL and an LOD of 0.12 pg/mL for malathion determination, and its application potential was verified by using it for the detection of spiked milk samples.
Inhibiting the generation of photoactive materials or releasing photoactive materials from the photoelectrode will result in a drop in the PEC signal.For example, a PEC sensor for asulam detection was developed based on the inhibitory effect on HRP enzyme activity and the lower production of S 2− from the conversion of S2O3 2− [153] (Figure 6b).Consequently, the amount of in situ-generated CdS reduced, and the photocurrent decreased with the concentration of asulam in a range from 0.02 to 2.0 ng/mL.The PEC sensor showed an LOD of 4.1 pg/mL and good accuracy in the analysis of spiked environmental water samples.Qin and coworkers proposed a PEC sensing platform for paraoxon detection by using a dissociable photoelectrode based on CdS nanocrystal-functionalized MnO2 NSs [154].TCh can effectively etch MnO2 NSs, causing the dissociation of MnO2-CdS from the photoelectrode and the decline of the photocurrent response.With the presence of organophosphate pesticides, the generation of TCh and the dissociation of MnO2 NSs were prevented due to the inhibition of AChE, thus recovering the PEC signals.Upon this signaling strategy, rolling circle amplification was introduced to assemble a large number of butyrylcholinesterase (BChE) for increased production of TCh and promoted dissociation of MnO2-CdS [155].Based on the inhibition of BChE by malathion, the PEC sensor possessed high sensitivity for malathion with a low LOD of 0.68 pg/mL and favorable accuracy in the analysis of spiked red wine and milk samples.

Energy Transfer
Energy transfer between the photoactive materials (namely, energy donor and acceptor) is a powerful approach to modulating the PEC properties of the PEC sensor.For PEC sensing of pesticides, the energy transfer strategy can be designed based on the recognition events, and the induced varying charge transfer behaviors will change the PEC conversion efficiency of the photoactive materials as well as the PEC signal [37].
Liu and coworkers reported a resonance energy transfer (RET) system from CdTe QDs to Au nanorods (NRs) for PEC aptasensing of acetamiprid [156].Multi-walled carbon nanotubes/reduced graphene oxide nanoribbons (MWCNTs/rGONRs) served as the PEC signal amplifier and support for CdTe QDs loading, and the proposed CdTe-MWCNTs/rGONRs exhibited the typical fluorescence emission overlapped with the UVvis absorption spectrum of Au NRs, leading to a RET process and photocurrent decrease.The binding of acetamiprid with aptamer resulted in the disassembly of the aptamer and low loading of Au NRs at the photoelectrode surface, thus inhibiting the RET process and recovering the photocurrent response (Figure 6c).The proposed PEC aptasensor was able to detect acetamiprid concentrations in the range of 0.5 pM to 10 µM with an LOD of 0.2 pM and was successfully applied to the direct detection of spiked apple and tomato samples.A split-type PEC sensor was designed for the detection of profenofos based on magneticassisted exciton-plasmon interactions (EPIs) [157] (Figure 6d).The target-triggered DNA double-stranded structure opening event released Au NPs-cDNA, which had significant overlap in the spectra of the Bi 2 S 3 /MoS 2 substrate.The simultaneous excitation of both excitons and plasmons led to EPI between Bi 2 S 3 /MoS 2 and Au NPs induced by SPR, which effectively suppressed the photocurrent generation.The PEC sensor exhibited good performance with a wide linear range (1.0 pg/mL-1.0µg/mL), a low LOD (0.23 pg/mL), and satisfactory results in the analysis of spiked milk, cucumber, wastewater, and soil samples.Wang and coworkers designed a perovskite/upconversion lab-on-paper PEC device for the sensitive detection of malathion based on CsPbBr 2 I@NaYF 4 :Yb,Tm/NiMn-layered double hydroxide/CdS/Au NPs functionalized working electrode and entropy-driven strand displacement amplification with a triple helix molecules switch strategy [158] (Figure 6e).A synergistic quenching effect including fluorescence energy resonance transfer (FRET) and photoinduced electron transfer (PET) was customized to efficiently decrease the photocurrent, achieving sensitive detection of malathion with a linear range from 0.01 ng/L to 5 µg/L and an LOD of 4.8 fg/L.The applicability of the PEC device was verified by determining malathion in spiked water, cabbage juice, spinach juice, and soil samples.
A summary of the different categories of photoactive materials and signaling mechanismsbased PEC sensors for pesticide sensing in food and environmental samples is recorded in Table 1.Combining various advanced photoactive materials with well-designed recognition and signaling strategies, some of the reported PEC sensors can detect pesticides with a wide linear range of several orders of magnitude and high sensitivity down to the picomole scale.The applicabilities of these PEC sensing platforms have been demonstrated by real sample analysis of food and environmental samples, such as vegetables, fruits, beverages, water, and soil samples.Meanwhile, the employed light source is necessary and important for the PEC conversion process.It can be seen that most of the PEC sensing systems utilized xenon (Xe) lamps, halogen lamps, and light-emitting diode (LED) energy-saving lamps as light sources to simulate natural sunlight, and some of the light sources were equipped with monochromators or UV cut-off filters to achieve visible-light excitation and avoid the harmful effects caused by UV irradiation.The applied bias provides driving forces for charge transfer from photoactive materials to photoelectrodes.Most of the PEC sensors in Table 1 used relatively low applied biases, for example, around 0 V. Compared to traditional electrochemical methods, PEC sensing methods are less dependent on the applied potential, which is not only energy-saving but also beneficial for a lower background and higher sensitivity.

Conclusions and Perspectives
PEC sensing has emerged as a promising method for the detection of pesticide residue levels in food and environmental samples.Its advantages, such as high sensitivity and selectivity, portability, rapid analysis, and user-friendly operation, make it a futuristic option for pesticide analysis.In recent years, there has been a significant development of novel PEC sensing systems and new sensing protocols for pesticide determination.This review provides a comprehensive summary of the progress in the development of PEC sensors for pesticide analysis, focusing on PEC sensing principles, categories of photoactive materials, PEC signaling mechanisms, and their applications in food and environmental media analysis.The integration of photoactive materials with high PEC conversion efficiency and signaling mechanisms with wise transduction strategies has significantly enhanced the sensitivity, selectivity, and application performance of PEC sensors.
In spite of advances, significant work still remains in the research on PEC sensing of pesticides.On one hand, the PEC sensing method still has some common limitations: (1) The inherent background signal of the detection method remains challenging for current PEC sensors.Self-referencing PEC sensors based on different voltages or wavelengths with dual channels have been proposed to detect several types of targets, and additional efforts should be put into constructing ratiometric PEC sensors for pesticide analysis with high sensitivity.(2) Most of the PEC sensing systems contain lamps as light sources, bulky photo-to-electrochemical signal conversion equipment, and external power sources.To meet the requirements of on-site pesticide analysis, utilizing sunlight as a light source, replacing conventional electrochemical workstations with miniaturized signaling devices, and using screen-printing electrodes or transparent paper-based conductive electrodes with high light transmittance as working electrodes may improve portability and practicality.
(3) Almost all reported PEC sensors are just carried out in laboratory research.Future efforts should be put into combining electronic information, micro-nanofabrication, and mass manufacturing to develop integrated detection devices with practicability.
On the other hand, as to the PEC sensing of pesticides, the following aspects should be considered besides the above limitations: Firstly, the coexistence of multiple toxic elements has led to a notable increase in threats to food and environmental safety.Most of the currently developed PEC sensing systems focus on only one pesticide and are not able to meet current needs.The construction of a PEC sensing platform that simultaneously detects multiple pesticides can better satisfy real needs.Secondly, the applicability of proposed PEC sensors for pesticide detection is mostly verified through the analysis of spiked samples or spiked sample extracts at present, and the application of real-life samples is still rare.Overall, applying the developed PEC sensors on the user end is the final goal in this field.As the aforementioned requirements are continuously met, the PEC sensing technique is poised to play a pivotal role in pesticide detection for food and environmental safety.

Figure 1 .
Figure 1.Schematic illustration of the building blocks of PEC sensing of pesticides: (a) photoactive materials and signaling mechanisms; (b) PEC sensing systems, targets, and real samples.

Figure 1 .
Figure 1.Schematic illustration of the building blocks of PEC sensing of pesticides: (a) photoactive materials and signaling mechanisms; (b) PEC sensing systems, targets, and real samples.

Figure 6 .Figure 6 .
Figure 6.(a) Schematic illustration of the PEC sensor based on HCR and in situ generation of Ag2S photosensitive material for the detection of malathion [151].Copyright 2021 Springer Nature.(b) Figure 6.(a) Schematic illustration of the PEC sensor based on HCR and in situ generation of Ag 2 S photosensitive material for the detection of malathion [151].Copyright 2021 Springer Nature.(b) Schematic illustration of the construction of a PEC sensor for asulam detection based on the in situ synthesis of CdS QDs [153].Copyright 2018 Elsevier.(c) Schematic illustration of the PEC acetamiprid aptasensor based on the RET from CdTe QDs to Au NRs [156].Copyright 2016 Elsevier.(d) Schematic illustration of the split-type PEC sensor for profenofos detection based on magnetic-assisted excitonplasmon interactions [157].Copyright 2023 Springer Nature.(e) Schematic illustration of the PEC sensor based on the cascade sensitization effect and synergetic quenching effect of FRET/PET [158].Copyright 2023 American Chemical Society.

Table 1 .
A summary of the different categories of photoactive materials and signaling mechanisms-based PEC sensors for pesticide sensing in food and environmental samples.