High Value Utilization of Waste Wood toward Porous and Lightweight Carbon Monolith with EMI Shielding, Heat Insulation and Mechanical Properties

With the increasing pollution of electromagnetic (EM) radiation, it is necessary to develop low-cost, renewable electromagnetic interference (EMI) shielding materials. Herein, wood-derived carbon (WC) materials for EMI shielding are prepared by one-step carbonization of renewable wood. With the increase in carbonization temperature, the conductivity and EMI performance of WC increase gradually. At the same carbonization temperature, the denser WC has better conductivity and higher EMI performance. In addition, due to the layered superimposed conductive channel structure, the WC in the vertical-section shows better EMI shielding performance than that in the cross-section. After excluding the influence of thickness and density, the specific EMI shielding effectiveness (SSE/t) value can be calculated to further optimize tree species. We further discuss the mechanism of the influence of the microstructure of WC on its EMI shielding properties. In addition, the lightweight WC EMI material also has good hydrophobicity and heat insulation properties, as well as good mechanical properties.


Introduction
With the development of technology and the use of electronic devices, electromagnetic (EM) radiation is also increasing. The signal radiation caused by electromagnetic interference (EMI) will interfere with the electronic system [1,2]. This EM radiation will not only cause equipment failure, but also affect human health. The only solution to prevent the harmful EM radiation from damaging electronic equipment is to provide a shield to filter interference. Therefore, in recent years, the research of EMI shielding materials has gradually attracted extensive attention [3]. Among them, the problem of EM radiation in buildings urgently needs extensive attention. In wooden or thin-walled houses, wireless radiation is easier to penetrate. Therefore, the development of materials with EMI shielding performance for buildings and furniture will have extensive application value.
Recently, metals and their oxides [4,5], conductive polymers [6,7] and carbon-based materials [8,9] have made great progress in the field of EMI shielding materials. As an excellent conductor and high thermal conductivity, metal has become a widely used electromagnetic shielding material. However, due to the high density, easy corrosion and difficult processing of metal, its application in lightweight products is limited. Compared with metal materials, polymer-based materials have great advantages in light weight and chemical stability [10][11][12][13]. However, polymer-based materials have the disadvantage of

Results and Discussion
In order to explore the influence of the structure of wood-based derived carbon on EMI shielding properties, the structures of three WC materials were photographed by scanning electron microscopy (SEM). As shown in Figure 2a-c, the cross-section diagrams of wood-derived carbon materials clearly observe the difference in pores in different kinds of wood. The vessel size of balsa wood is larger than the other two kinds of wood, and the porosity is the highest (Figure 2a). The pore structure of basswood is relatively uniform (Figure 2b). Beech is more compact than the other two kinds of wood ( Figure 2c). It can be observed from SEM images of cross-section that the WC materials has natural connected channels and regular layered frame structure. This structure has good connectivity, which is very conducive to the conduction of electrons, so that it has high conductivity. When the EM wave passes through this channel structure, it is very beneficial to generate strong EM multiple scattering and reflection [34][35][36][37]. Good vertical channel structure can be seen from the vertical-section of three kinds of WC (Figure 2d-f). We further magnified and observed the surface of the inner wall of the channel of WC material (Figure 2d'-f'). After carbonization, the wood still retains the unique cell wall structure of different kinds of wood. The inner wall of the interconnected channel can be used as an effective EM wave reflecting surface to make the EM wave enter the framework of the carbonized wood and interact with the electrons, resulting in ohmic current loss. The EM wave will repeat the previous loss process when passing through each channel, thus realizing the layered loss of EM wave [29].

Results and Discussion
In order to explore the influence of the structure of wood-based derived carbon on EMI shielding properties, the structures of three WC materials were photographed by scanning electron microscopy (SEM). As shown in Figure 2a-c, the cross-section diagrams of wood-derived carbon materials clearly observe the difference in pores in different kinds of wood. The vessel size of balsa wood is larger than the other two kinds of wood, and the porosity is the highest (Figure 2a). The pore structure of basswood is relatively uniform (Figure 2b). Beech is more compact than the other two kinds of wood ( Figure 2c). It can be observed from SEM images of cross-section that the WC materials has natural connected channels and regular layered frame structure. This structure has good connectivity, which is very conducive to the conduction of electrons, so that it has high conductivity. When the EM wave passes through this channel structure, it is very beneficial to generate strong EM multiple scattering and reflection [34][35][36][37]. Good vertical channel structure can be seen from the vertical-section of three kinds of WC (Figure 2d-f). We further magnified and observed the surface of the inner wall of the channel of WC material (Figure 2d -f ). After carbonization, the wood still retains the unique cell wall structure of different kinds of wood. The inner wall of the interconnected channel can be used as an effective EM wave reflecting surface to make the EM wave enter the framework of the carbonized wood and interact with the electrons, resulting in ohmic current loss. The EM wave will repeat the previous loss process when passing through each channel, thus realizing the layered loss of EM wave [29]. The XRD spectra of three wood-derived carbon samples are shown in the Figure 3a. The (0 0 2) plane of graphite has a typical wide diffraction peak at about 24° [38]. This diffraction peak was observed in the XRD spectra of WC samples of three kinds of wood at different carbonization temperatures. This indicates that the carbonization process makes the wood graphitized. With the increase in carbonization temperature, the diffraction peak around 24° gradually becomes sharp, indicating that the degree of graphitization increases. In Raman spectra of Figure 3b, the D band (1340 cm −1 ) and G band (1590 cm −1 ) correspond to defective/disordered carbon and graphitic carbon, respectively. D and G bands are observed in all WC samples, which further indicates that the carbonization process makes the wood graphitized. In three WC samples, the ID/IG ratios of WC-600, WC-800 and WC-1000 all gradually decrease, indicating that carbonization facilitated the graphitization of samples [39]. The results are consistent with the analysis of XRD spectra.
The light weight of WC is very important advantage for applying EM shielding [40]. Wood itself is a natural lightweight biomass. The carbonization process is the reaction of heating and decomposing wood under the condition of isolating air. In the process, natural wood will decompose into tar, water and other substances, while releasing a large The XRD spectra of three wood-derived carbon samples are shown in the Figure 3a. The (0 0 2) plane of graphite has a typical wide diffraction peak at about 24 • [38]. This diffraction peak was observed in the XRD spectra of WC samples of three kinds of wood at different carbonization temperatures. This indicates that the carbonization process makes the wood graphitized. With the increase in carbonization temperature, the diffraction peak around 24 • gradually becomes sharp, indicating that the degree of graphitization increases. In Raman spectra of Figure 3b, the D band (1340 cm −1 ) and G band (1590 cm −1 ) correspond to defective/disordered carbon and graphitic carbon, respectively. D and G bands are observed in all WC samples, which further indicates that the carbonization process makes the wood graphitized. In three WC samples, the I D /I G ratios of WC-600, WC-800 and WC-1000 all gradually decrease, indicating that carbonization facilitated the graphitization of samples [39]. The results are consistent with the analysis of XRD spectra. basswood is 63°, and the contact angles of WC-600, WC-800 and WC-1000 after carbonization are 94°, 99° and 101° respectively. The contact angle of natural beech is 74°, and the contact angles of WC-600, WC-800 and WC-1000 after carbonization are 97°, 101° and 107°, respectively. The contact angles of WC of balsa wood, basswood and beech increases with the increase in carbonization temperature. It can be seen from contact angles that woodderived carbon all show hydrophobicity, which is essential for EMI materials to achieve self-cleaning [48].  The light weight of WC is very important advantage for applying EM shielding [40]. Wood itself is a natural lightweight biomass. The carbonization process is the reaction of heating and decomposing wood under the condition of isolating air. In the process, natural wood will decompose into tar, water and other substances, while releasing a large amount of gas. Therefore, the volume of wood after carbonization will shrink greatly, and the density will also decrease significantly. The densities of balsa wood, basswood and beech before and after carbonization are recorded in the Figure 3c. After carbonization, the densities of basswood and beech decline substantially. The densities of balsa wood, basswood and beech after carbonization at 1000 • C are 200, 230 and 330 mg cm −3 , respectively. Obviously, the density of WC materials meets the requirements of lightweight electromagnetic interference shielding material [29,33,41].
Conductivity is important for EM shielding materials [42]. The electrical conductivity of wood-derived carbon increases gradually, with the increase in carbonization temperature ( Figure 3d) [43,44]. The interconnected structure of the wood facilitates the rapid transmission of electrons within the WC [45]. With the increase in the graphitization degree in WC, their electrical conductivities are further improved [46]. The WC-1000 of balsa wood exhibits a smaller electrical conductivity (10 S cm −1 ). The conductivity of WC-1000 of bass wood increases to 23 S cm −1 , and that of WC-1000 of beech increased significantly to 39 S cm −1 . Obviously, WC with higher wood density exhibits higher electrical conductivity. The pore distributions are analyzed by N 2 adsorption and desorption experiments ( Figure 3e). WC-1000 of balsa wood, basswood and beech all are type-S isothermal curve, which belongs to the pore structure inherent in the wood. According to the pore size of the pore distributions and SEM images of the cross section of the WC materials, the WC materials are mainly composed of macropores.
The self-cleaning performance is also an important advantage for the EMI materials [47]. The contact angles between natural wood and WC were tested. (Figure 3f • and 107 • , respectively. The contact angles of WC of balsa wood, basswood and beech increases with the increase in carbonization temperature. It can be seen from contact angles that wood-derived carbon all show hydrophobicity, which is essential for EMI materials to achieve self-cleaning [48]. Firstly, the balsa wood with the lowest density was selected to test the EM shielding performance of wood-derived carbon at different carbonization temperature. In order to eliminate the influence of sample thickness on EMI shielding performance, WC samples are uniformly ground to a thickness of 2 mm. The EMI shielding performances of wood, WC-600, WC-800 and WC-1000 of balsa wood at a 2 mm thickness at 8.2-12.4 GHz (X-band) in the cross-section are shown in Figure 4a Firstly, the balsa wood with the lowest density was selected to test the EM shielding performance of wood-derived carbon at different carbonization temperature. In order to eliminate the influence of sample thickness on EMI shielding performance, WC samples are uniformly ground to a thickness of 2 mm. The EMI shielding performances of wood, WC-600, WC-800 and WC-1000 of balsa wood at a 2 mm thickness at 8. 2-12.4 GHz (Xband) in the cross-section are shown in Figure 4a,b. Obviously, the total shielding effectiveness (SET) of natural wood, WC-600, WC-800 and WC-1000 increases with the increase in carbonization temperature (Figure 4a). The average values of total shielding effectiveness (SET) of the wood and WC-600 are only 0.9 and 15.2 dB, respectively (Figure 4b). The average SET values of WC-800 and WC-1000 are 18.8 and 22.1 dB, respectively. This is because the enhanced conductivity of WC with the increase in carbonization temperature [48]. In addition, these values of reflection efficiency (SER) and absorption efficiency (SEA) of WC samples in the cross-section are calculated by the measured S parameters. The SEA values of WC-600, WC-800 and WC-1000 were 10.4, 10.5 and 14.1 dB, respectively. The SER values of WC-600, WC-800 and WC-1000, respectively, were 7.0, 8.1 and 7.9 dB. These values of SEA are markedly higher than that of SER.
The average transmission coefficient (T), absorption coefficient (A) and reflection coefficient (R) values are further analyzed (Figure 4c) [36]. For WC-600, WC-800 and WC-1000, the R values are all much larger than the A values, indicating that the EMI mode of WC is mainly reflection. Moreover, in order to evaluate the shielding effect of WC materials on EM waves, the EMI shielding efficiencies of samples are further calculated. The total SET shielding efficiency of WC-1000 of balsa wood reaches 99 % (Figure 4d). By comparing the shielding performance of WC samples at different carbonization temperatures of balsa wood, it can be proved that increasing carbonization temperature can improve the shielding performance of WC samples. Therefore, in subsequent experiments, WC samples with carbonization temperature of 1000 °C were selected to further explore the influence of Wood species, sections and thickness on EMI shielding performance.  The average transmission coefficient (T), absorption coefficient (A) and reflection coefficient (R) values are further analyzed (Figure 4c) [36]. For WC-600, WC-800 and WC-1000, the R values are all much larger than the A values, indicating that the EMI mode of WC is mainly reflection. Moreover, in order to evaluate the shielding effect of WC materials on EM waves, the EMI shielding efficiencies of samples are further calculated. The total SE T shielding efficiency of WC-1000 of balsa wood reaches 99% (Figure 4d). By comparing the shielding performance of WC samples at different carbonization temperatures of balsa wood, it can be proved that increasing carbonization temperature can improve the shielding performance of WC samples. Therefore, in subsequent experiments, WC samples with carbonization temperature of 1000 • C were selected to further explore the influence of Wood species, sections and thickness on EMI shielding performance.
In order to further analyze the shielding mechanism, we have tested the shielding properties of three kinds of wood (balsa wood, basswood and beech) at different cross sections. The EMI shielding performances of WC-1000 of balsa wood, basswood and beech at different cross sections (cross section and vertical section) are shown in Figure 5a (Figure 5d). Obviously, WC with higher density has better shielding performance. It may be that the wood with high density has a denser structure after carbonization, which is more conducive to the conduction of electrons and shows a higher conductivity [49]. Conductivity is an important factor of EM shielding materials. In addition, the cross-sectional SE T values of WC-1000 (balsa wood, basswood and beech) are markedly less than that of the vertical-sectional SE T values. This difference may be due to the fact that the tubes inside the wood in the cross-section are parallel to the incident direction of EM waves, resulting in a small amount of EM waves may directly penetrate from the inside of the tubes, forming a wave transmission phenomenon. Evidently, the directional superimposed conductive path of WC materials is conducive to multiple reflection and dissipation of EM waves.
properties of three kinds of wood (balsa wood, basswood and beech) at different cross sections. The EMI shielding performances of WC-1000 of balsa wood, basswood and beech at different cross sections (cross section and vertical section) are shown in Figure 5a,b. The cross-sectional average SET values of WC-1000 (balsa wood, basswood and beech) are 22.1, 25.0 and 26.3 dB, respectively (Figure 5c). Similarly, the sectional average SET values of WC-1000 (balsa wood, basswood and beech) are 25.1, 27.6 and 28.6 dB, respectively, which also exhibited a significantly increasing trend (Figure 5d). Obviously, WC with higher density has better shielding performance. It may be that the wood with high density has a denser structure after carbonization, which is more conducive to the conduction of electrons and shows a higher conductivity [49]. Conductivity is an important factor of EM shielding materials. In addition, the cross-sectional SET values of WC-1000 (balsa wood, basswood and beech) are markedly less than that of the vertical-sectional SET values. This difference may be due to the fact that the tubes inside the wood in the cross-section are parallel to the incident direction of EM waves, resulting in a small amount of EM waves may directly penetrate from the inside of the tubes, forming a wave transmission phenomenon. Evidently, the directional superimposed conductive path of WC materials is conducive to multiple reflection and dissipation of EM waves.
The reflection efficiency (SER) and absorption efficiency (SEA) values of WC-1000 samples in the cross section and vertical section are shown in Figure 5c (Figure 5e,f), which further indicates that WC materials are mainly reflect EM waves. According to the above data analysis, the higher the wood density, the higher the shielding efficiency of the WC sample in different wood varieties.
The EMI shielding efficiencies of WC-1000 materials (balsa wood, basswood and beech) at cross section and vertical section are further analyzed. The EMI shielding efficiencies of all samples are higher than 99 % at a thickness of 2 mm (Figure 6a). In cross section, the EMI shielding efficiencies of WC-1000 samples (balsa wood, basswood and beech) are 99.4 %, 99.7 % and 99.8 %, respectively. In vertical section, the EMI shielding efficiencies of WC-1000 samples (balsa wood, basswood and beech) are 99.7 %, 99.8 % and 99.9 %, respectively. It can be clearly seen from the shielding efficiencies of the vertical-sectional WC is higher than that of the cross-section. The shielding efficiency of beech WC-1000 in vertical section reaches 99.9 %, indicating that the material can shield almost all EM waves.
The thickness and density both have an important impact on EMI shielding materials. Therefore, specific EMI shielding effectiveness (SSE/t, SE divided by density and thickness) is often used as a standard to analyze the EMI shielding ability of a material [50]. In cross section, the EMI SSE/t values of WC-1000 samples (balsa wood, basswood and beech) are 550.6 dB cm 2 g −1 , 557.6 dB cm 2 g −1 and 400.4 dB cm 2 g −1 , respectively. In vertical section, the EMI SSE/t values of WC-1000 samples (balsa wood, basswood and beech) are 627.3 dB cm 2 g −1 , 626.4 dB cm 2 g −1 and 424.8 dB cm 2 g −1 , respectively. Clearly, SSE/t values of WC-1000 of balsa wood and basswood are higher than that of WC-1000 of beech (Figure 6b). Considering that the average SET value of basswood is higher than that of balsa wood, the shielding performance of wood-derived carbon materials of basswood is better than that of balsa wood and beech.
The thickness of the material will affect the shielding value, and the EMI shielding performances will improve with the increase in the thickness. The total SET of WC-1000 of basswood/WC-1000 at different thickness (2.0 mm, 2.5 mm, 3.0 mm, 3.5 mm and 4 mm) are further tested (Figure 6c). Obviously, it can be seen from the total SET that the WC-1000 samples gradually increase with the increase in thickness. As the thickness increases, the SET value of WC-1000 of basswood exceeds 40 dB at a thickness of 4 mm. The EMI shielding efficiencies of WC-1000 materials at different thickness (2.0 mm, 2.5 mm, 3.0 mm, 3.5 mm and 4 mm) are further analyzed. The shielding efficiency of WC-1000 of basswood is higher than 99.99% at a thickness of 4 mm, which is sufficient to shield most EM waves (Figure 6d).  The thickness and density both have an important impact on EMI shielding materials. Therefore, specific EMI shielding effectiveness (SSE/t, SE divided by density and thickness) is often used as a standard to analyze the EMI shielding ability of a material [50]. In cross section, the EMI SSE/t values of WC-1000 samples (balsa wood, basswood and beech) are 550.6 dB cm 2 g −1 , 557.6 dB cm 2 g −1 and 400.4 dB cm 2 g −1 , respectively. In vertical section, the EMI SSE/t values of WC-1000 samples (balsa wood, basswood and beech) are 627.3 dB cm 2 g −1 , 626.4 dB cm 2 g −1 and 424.8 dB cm 2 g −1 , respectively. Clearly, SSE/t values of WC-1000 of balsa wood and basswood are higher than that of WC-1000 of beech (Figure 6b). Considering that the average SE T value of basswood is higher than that of balsa wood, the shielding performance of wood-derived carbon materials of basswood is better than that of balsa wood and beech.
The thickness of the material will affect the shielding value, and the EMI shielding performances will improve with the increase in the thickness. The total SE T of WC-1000 of basswood/WC-1000 at different thickness (2.0 mm, 2.5 mm, 3.0 mm, 3.5 mm and 4 mm) are further tested (Figure 6c). Obviously, it can be seen from the total SE T that the WC-1000 samples gradually increase with the increase in thickness. As the thickness increases, the SE T value of WC-1000 of basswood exceeds 40 dB at a thickness of 4 mm. The EMI shielding efficiencies of WC-1000 materials at different thickness (2.0 mm, 2.5 mm, 3.0 mm, 3.5 mm and 4 mm) are further analyzed. The shielding efficiency of WC-1000 of basswood is higher than 99.99% at a thickness of 4 mm, which is sufficient to shield most EM waves (Figure 6d).
The EM shielding mechanism of the WC is simulated in Figure 7. The conductive wood-carbon skeleton contains a large number of free electrons, which can generate current induced by EM field and realize conduction loss [41]. EM wave passing through the directionally superimposed layered conductive frame can accelerate the reflection loss of EM wave. In addition, the hierarchical porous structure of WC has a large internal surface area, which is conducive to the EM wave into the interior and microwave attenuation. EM waves cause various types of scattering inside the pore channel of WC. In addition, due to the regular reticulated layered frame structure of WC materials, EM waves will reflect when contacting the conductive channels of each layer. Then, when the EM waves contact the next layer of channel in WC materials, it will repeat the EM loss process of the previous layer, so as to finally achieve the effect of shielding by reducing the EM wave layer by layer.
Molecules 2023, 28, x FOR PEER REVIEW 9 of 13 The EM shielding mechanism of the WC is simulated in Figure 7. The conductive wood-carbon skeleton contains a large number of free electrons, which can generate current induced by EM field and realize conduction loss [41]. EM wave passing through the directionally superimposed layered conductive frame can accelerate the reflection loss of EM wave. In addition, the hierarchical porous structure of WC has a large internal surface area, which is conducive to the EM wave into the interior and microwave attenuation. EM waves cause various types of scattering inside the pore channel of WC. In addition, due to the regular reticulated layered frame structure of WC materials, EM waves will reflect when contacting the conductive channels of each layer. Then, when the EM waves contact the next layer of channel in WC materials, it will repeat the EM loss process of the previous layer, so as to finally achieve the effect of shielding by reducing the EM wave layer by layer. In practical application, EMI shielding materials should have good thermal insulation and mechanical properties. Therefore, we further tested the thermal insulation and mechanical properties of wood-derived carbon. Flammable cotton is placed on the surface of wood-derived carbon and heated at the bottom with an alcohol flame (Figure 8a). After heating for 120 s, the cotton maintains a good shape, indicating that the wood-derived carbon has good heat insulation performance. The experimental results show that WC materials as EMI shielding material is expected to adapt to the actual work in extreme high temperature environment. The compressive stress-strain curves of wood-derived carbons are showed in Figure 8b. The compressive stresses of beech/WC-1000, basswood/WC-1000 and balsa wood/WC-1000 are 55.2 MPa, 31.8 MPa and 6.9 MPa, respectively. Obviously, with the increase in density, the mechanical properties of wood-derived carbon are gradually enhanced. The wood-derived carbon of basswood and beech both showed excellent mechanical properties. In general, the carbonized wood (WC materials) retains its unique good mechanical properties. Compared with traditional carbon-based porous materials, it has good mechanical properties [51]. In practical application, EMI shielding materials should have good thermal insulation and mechanical properties. Therefore, we further tested the thermal insulation and mechanical properties of wood-derived carbon. Flammable cotton is placed on the surface of wood-derived carbon and heated at the bottom with an alcohol flame (Figure 8a). After heating for 120 s, the cotton maintains a good shape, indicating that the wood-derived carbon has good heat insulation performance. The experimental results show that WC materials as EMI shielding material is expected to adapt to the actual work in extreme high temperature environment. The compressive stress-strain curves of wood-derived carbons are showed in Figure 8b. The compressive stresses of beech/WC-1000, basswood/WC-1000 and balsa wood/WC-1000 are 55.2 MPa, 31.8 MPa and 6.9 MPa, respectively. Obviously, with the increase in density, the mechanical properties of wood-derived carbon are gradually enhanced. The wood-derived carbon of basswood and beech both showed excellent mechanical properties. In general, the carbonized wood (WC materials) retains its unique good mechanical properties. Compared with traditional carbon-based porous materials, it has good mechanical properties [51].
The EMI shielding effectiveness was measured with the Vector Network Analyzer (Agilent Technologies N5063A, Palo Alto, State of California, USA) ( Figure S1). Schematic sketch of this instrument is showed in Figure S2 (see Supplementary Materials). Samples were uniformly polished into 22.86 mm × 10.16 mm cuboids to fit the specific waveguide sample holders in X-band frequency (8.2-12.4 GHz), and analyzed by using the method of waveguide with rectangular regions. EMI shielding materials, via reflection, absorption and transmission, shield EM waves. According to the law of conservation of energy, transmission coefficient (T), reflection coefficient (R) and absorption coefficient (A) can be expressed as:

Fabrication of WC-600, WC-800 and WC-1000
The wood-derived carbon (WC) samples of balsa wood basswood and beech are prepared by carbonizing wood for 1 h at the specified temperature (600, 800, 1000 • C) under N 2 atmosphere and heating rate (5 • C min −1 ). The products were respectively named WC-600, WC-800 and WC-1000.
The EMI shielding effectiveness was measured with the Vector Network Analyzer (Agilent Technologies N5063A, Palo Alto, State of California, USA) ( Figure S1). Schematic sketch of this instrument is showed in Figure S2 (see Supplementary Materials). Samples were uniformly polished into 22.86 mm × 10.16 mm cuboids to fit the specific waveguide sample holders in X-band frequency (8.2-12.4 GHz), and analyzed by using the method of waveguide with rectangular regions. EMI shielding materials, via reflection, absorption and transmission, shield EM waves. According to the law of conservation of energy, transmission coefficient (T), reflection coefficient (R) and absorption coefficient (A) can be expressed as: where S 11 and S 21 denote the reflection and transmission coefficient, respectively. The total EMI shielding effectiveness (SE T ) can, thus, be divided into three aspects: the reflection effectiveness (SE R ), the absorption effectiveness (SE A ) and the multiple reflection effec-tiveness (SE MR ). SE MR is generally ignored if the SE T is more than 15 dB. The shielding effectiveness can be rewritten using the following formulas: EMI shielding efficiency (%) refers to the percentage value used to evaluate the ability to block EM waves, which is obtained from the formula: Shielding e f f iciency (%) = 100 − ( 1 10 SE 10 ) × 100 In order to fairly compare the actual effectiveness of EMI shielding materials, specific shielding effectiveness (SSE) and SSE/t considering thickness and density are generally used, as shown below: SSE t = EMI SE density × thickness dB cm 2 · g − 1

Conclusions
As a renewable biomass, wood has a good hierarchical porous structure. Conductive wood carbon skeleton can generate EM field-induced current and realize conduction loss. Directionally stacked layered conductive frame can accelerate the reflection loss of EM waves. The layered porous structure of WC is conducive to EM waves entering the interior and microwave attenuation. In addition, due to the regular reticulated layered frame structure of WC materials, the EM waves will repeat the loss process of the previous layer when contacting the conductive channels of each layer. At the same carbonization temperature and the same thickness, high-density wood with longitudinal section has better EMI performance. However, it is necessary to further analyze SSE/t values of WC after removing the influence of thickness and density. In addition, WC derivatives also show the advantages of light weight, hydrophobic, thermal insulation and high mechanical properties. Therefore, WCs as good EMI shielding materials is expected to replace nonrenewable high-cost materials. The research of this work could provide a research basis for the further development of wood-based EMI shielding materials.
Supplementary Materials: The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/molecules28062482/s1, Figure S1: Pictures of the Vector Network Analyzer (Agilent Technologies N5063A, USA). Figure S2: Schematic sketch shows the instrument used to evaluate the EMI SE.

Data Availability Statement:
The data used to support the findings of this study are available from the corresponding author upon request.