MoS2 and MoS2 Nanocomposites for Adsorption and Photodegradation of Water Pollutants: A Review

The need for fresh and conveniently treated water has become a major concern in recent years. Molybdenum disulfide (MoS2) nanomaterials are attracting attention in various fields, such as energy, hydrogen production, and water decontamination. This review provides an overview of the recent developments in MoS2-based nanomaterials for water treatment via adsorption and photodegradation. Primary attention is given to the structure, properties, and major methods for the synthesis and modification of MoS2, aiming for efficient water-contaminant removal. The combination of MoS2 with other components results in nanocomposites that can be separated easily or that present enhanced adsorptive and photocatalytic properties. The performance of these materials in the adsorption of heavy metal ions and organic contaminants, such as dyes and drugs, is reviewed. The review also summarizes current progress in the photocatalytic degradation of various water pollutants, using MoS2-based nanomaterials under UV-VIS light irradiation. MoS2-based materials showed good activity after several reuse cycles and in real water scenarios. Regarding the ecotoxicity of the MoS2, the number of studies is still limited, and more work is needed to effectively evaluate the risks of using this nanomaterial in water treatment.


Introduction
The world's population has been growing yearly, and an increased need for resources has accompanied this growth [1]. Industrial, agricultural, and medical development have evolved to supply this population growth [1,2]. However, after this substantial increase in resource consumption, pollution had also increased, becoming a huge concern, along with the need for freshwater sources or for effective water treatment [1,3]. In this regard, several approaches for water treatment have been developed, such as adsorption and photocatalysis, to remove pollutants and other threats to human health and ecosystems, such as heavy metals, dyes, drugs, and pesticides, among others [4][5][6][7][8].
Along with the advances in environmental research, in the past few years, several authors have suggested nanomaterials to enhance primary and advanced water treatment [9]. Due to its small size and, consequently, high surface and reactive areas, the use of nanomaterials enables the improvement of several properties compared to bulk material [9]. More recently, two-dimensional (2D) nanomaterials have gained importance. In this group are included materials such as graphene, hexagonal boron nitride, 2D honeycomb silicon, and transition metal dichalcogenides (TMD) such as molybdenum disulfide (MoS 2 ) and tungsten disulfide (WS 2 ) [10]. TMD are hexagonal, structured and layered materials with the molecular formula MX 2 , where M is a transition metal (Mo, W, or Nb) and X represents a chalcogen element (S, Se, or Te) [11,12]. Within this group of materials, nano-MoS 2 has gained attention year after year due to its outstanding chemical, electronic, catalytic, optical, and mechanical properties, making it suitable for various fields such as pollution 2 of 32 remediation and sensors, medicine, mechanics and electronics, and energy conversion and storage [13][14][15][16][17][18][19][20][21][22][23][24]. When compared to other sulfides, such as zinc sulfide (ZnS), cadmium sulfide (CdS), and tungsten sulfide (WS 2 ), MoS 2 show promising photocatalytic activity, allied to its easy preparation and unique optical and electronic properties [25]. The wide band gaps of ZnS and MnS render them responsive to only UV light; further modification is required to extend the light absorption range [26]. In contrast, MoS 2 is active with visible light. As a photocatalytic material, MoS 2 presents a suitable surface area with a large number of active site edges, a layered structure that allows good adsorption capacity, and a tunable band gap between 1.2 eV and 1.9 eV, depending on the number of layers [27]. Regarding safety considerations, Mo is less hazardous and can be used to substitute Cd, which is known to be a human carcinogen.
In this review, we first summarize the main structures and properties of MoS 2 and the most common methods by which to prepare MoS 2 -based materials. We then critically review the recent advances in MoS 2 -based materials for water treatment and purification through adsorption and photocatalysis.

MoS 2 Structure and Properties
In nature, MoS 2 exists in molybdenite bulk mineral form as a black powder [28]. Bulk MoS 2 can be exfoliated, obtaining few-layer nanosheets (FLMoS 2 ) and single-layer nanosheets (SLMoS 2 ) [29,30]. SLMoS 2 compared to bulk MoS 2 has intrinsic higher electronic conductivity and presents a direct gap of 1.7-1.9 eV, while bulk MoS 2 presents an indirect band gap of 1.1-1.3 eV [31][32][33][34]. This relatively small band gap of SLMoS 2 enables the use of visible light to perform photocatalytic reactions [35,36]. While absent in the bulk material, SLMoS 2 also shows strong photoluminescence [37]. At room temperature, SLMoS 2 exhibits an on/off current ratio of 10 8 and an electron mobility of 200 cm 2 (V.s) −1 [38]. Notably, several properties of MoS 2 can be adjusted by varying the number of layers and polymorphism. SLMoS 2 presents a sandwich structure with a thickness of 0.6 nm, composed of two layers of atomic S, with a single layer of atomic Mo between, linked through Mo-S covalent bonds [39][40][41]. In the case of FLMoS 2 , the different sheets interact with each other via weak van der Waals (vdW) forces [40,42]. Because of these weak vdW forces, changing SLMoS 2 to FLMoS 2 and gaining the reverse reaction is easily achieved [41]. Kumar and Mishra demonstrated, via molecular simulation, the mechanism of solvent-assisted exfoliation to turn bulk MoS 2 into FLMoS 2 by applying a shock-wave method [43].
MoS 2 presents several polymorphs, depending on the interlayer stacking arrangement and intralayer coordination between the central Mo atom and the surrounding S atoms, the crystal structures of which are shown in Figure 1 [41,44,45]. The MoS 2 polymorphs are identified using an adapted version of Ramsdell's notation that was introduced for SiC polytypes [46]. This nomenclature indicates the number of S-Mo-S layers in the unit cell (1, 2, or 3) and the crystal system of the lattice, where "T", "H", and "R" stand for trigonal, hexagonal, and rhombohedral, respectively [47]. Five polymorphic forms have been identified for MoS 2 : 1T, 1T', 1H, 2H, and 3R [4,33,44,[48][49][50][51][52][53][54][55]. The forms 1T, 2H, and 3R are polytypes because they differ in terms of stacking configuration. The polytypes 2H and 3R occur naturally, while 1T is a metastable structure. The semiconducting 2H phase is naturally more stable and has been extensively investigated for energy-related applications [56,57], transistors [58], photodetectors [59], valleytronics, spintronic devices, and optoelectric devices [58,60,61]. In the 2H-MoS 2 phase, each Mo coordinates with S atoms in a trigonal prismatic arrangement, with two layers in each unit cell in hexagonal symmetry, as shown in Figure 1. The semiconducting behavior of 2H-MoS 2 results from a finite band gap between filled d z 2 and empty d x 2 −y 2 ,xy bands [62]. The 2H-MoS 2 phase can easily be turned into the 1T phase by exfoliating the 2H-MoS 2 nanosheets, using the sonication-assisted lithium intercalation method, and treating the resulting material with an infrared laser [63]. With the same prismatic coordination as the 2H MoS 2 , but with three stacking layers of S-Mo-S directed along the c-axis instead of two (Figure 1), the rhombohedral 3R phase is also a naturally occurring semiconducting phase. Due to the broken inversion symmetry, this phase has drawn extensive attention because of its potential applications for non-linear optical devices [64][65][66]. Compared to monolayers, the 3R phase presents a higher predicted piezoelectricity coefficient [64]. The 3R-phase can be synthesized via homoepitaxial growth through chemical vapor deposition [67,68]. Through heating, the 3R phase can easily turn into the 2H phase [69].
The monolayered 1T, 1H and 1T'-MoS 2 phases are other polytypes that have attracted attention but do not occur naturally. Depending on the S-atom's geometry coordination, the Mo atom can be coordinated by six S atoms in either an octahedral (1T) or trigonal prismatic (1H) arrangement [44]. The 1T-phase can be obtained via exfoliation of the 2H-phase [70]. It is metallic in nature, with an electrical conductivity 10 7 times higher than the 2H phase, and is of interest as a supercapacitor electrode material [70,71]. This metastable and paramagnetic phase has been reported to be efficient as a photocatalyst for hydrogen evolution and gas molecule adsorption, due to the high surface activity at the basal sites [44,45,52,53,62,70]. It is also known that the 1T phase can turn into the 2H phase with high-temperature treatment [62]. The semimetallic 1T'-phase, the more stable SLMoS 2 with a distorted structure, due to the clusterization of Mo atoms, is formed through the dimerization of Mo atoms in the 1T phase [54]. The 1H phase is a semiconductor. It is possible to turn 1H-MoS 2 into 1T-MoS 2 by applying the Li intercalation method, in which an electron is transferred from the alkali metal to the d orbital of the transition metal center, resulting in the metallic-like character of the material [54].
The phase composition influences the photocatalytic performance of MoS 2 nanosheets. Materials comprising 1T/2H phases have shown higher performance in the photodegradation of methyl orange dye, compared to the 2H and 3R phases [69]. Computational studies have indicated that this enhanced photocatalytic activity is due to the emergence of mid-gap states upon the introduction of 1T sites to the 2H lattice. Density functional theory (DFT)-based calculations investigating the material's structural and electronic properties found a zero tunnel-barrier height in stable 2H/1T heterostructures, which is advantageous for achieving an efficient carrier injection rate [72].
Regarding the adsorptive properties, according to the principle of a "hard and soft acid and basis" (HSAB), soft acids (such as heavy metal ions) are capable of strong interaction with soft bases, such as sulfur atoms [73]. Thus, the MoS 2 nanosheets show high adsorption capacity due to the abundance of adsorption sites and the fast kinetics caused by easy access to those sites [74]. Concerning solubility, MoS 2 is soluble in aqua regia and in hot concentrated sulfuric acid, but it shows insolubility in water and diluted acid, indicating long-term stability in water systems [75].

Common Synthesis Methods and Modifications of MoS 2
MoS 2 nanosheets can be synthesized through top-down methods, which consist of exfoliating the bulk MoS 2, and the bottom-up approach, consisting of growing nanosheets from single atoms using chemical methods such as chemical vapor deposition (CVD) or the hydrothermal method. Exfoliation processes are highly efficient and conveniently scalable, producing by-products that are less hazardous and lower costs than bottom-up methods [76,77]. However, bottom-up methods provide better control of phase composition and morphology.   [78]. Copyright (2018), with permission from Elsevier. (b) Ballmilling method. Reprinted from [79]. Copyright (2020), with permission from Elsevier. (c) Liquid phase exfoliation method. Reprinted from [80]. Copyright (2019), with permission from Elsevier. (d) Chemical vapor deposition method. Reprinted from [81]. Copyright (2021), with permission from Elsevier. (e) Chemical vapor deposition method. Adapted from [82]. Copyright (2020), with permission from Elsevier. (f) Hydrothermal method. Reprinted from [83]. Copyright (2019), with permission from Elsevier.

Top-Down Methods
One of the main top-down methods is mechanical exfoliation through the 'Scotch-tape' method. The basis of this method is to strip the MoS 2 flakes using tapes. The 'Scotchtape' method is considered a non-destructive method in which chemical reactions are not involved [10]. Although this method has a low yield, is time-consuming, and leads to a low quantity of product, it produces SLMoS 2 in the form of flakes and is a simple process requiring accessible equipment. This technique also enables MoS 2 with high quality and crystallinity in 2D [10,84]. Ball-milling is another mechanical exfoliation method. This method can be employed in both dry and wet states. Dry ball-milling can be used to greatly enhance the electrochemical and catalytic properties of bulk MoS 2 [85]. However, wet ball-milling leads to the increased production of FLMoS 2 when compared to dry ballmilling [10]. According to Tayyebi et al. [86], the pre-functionalization of the materials can weaken the force interacting between the layers, facilitating exfoliation during the ball-milling process.
Another top-down method is liquid-phase exfoliation. In this approach, the bulk material is dispersed in a solvent and then exfoliated via mechanical processes, such as ultrasonication [87]. This method enables the high-yield creation of 2D flakes in suspension as a scalable production [88,89]. However, after long periods of inactivity or after taking the solvent out, the nanosheets could restack back into bulk form. The addition of a polymer may stabilize the MoS 2 nanosheets, thereby maintaining the properties of exfoliated nanosheets. For instance, Deepak et al. [77] added the polymer poly(vinylidene fluorideco-hexafluoropropylene) (PVDF-HFP) and used dimethylformamide (DMF) as a solvent in the liquid-phase exfoliation method. Due to its surface energy, water is not considered a suitable solvent for this method. However, hot water has already been employed to exfoliate MoS 2, with satisfactory results [87]. The liquid-phase exfoliation can be assisted by ion intercalation to enhance the yield. Ions such as lithium can penetrate the layers of MoS 2 , weakening the interlayer forces and facilitating the detachment of the layers, allowing the production of SLMoS 2 . However, this method decreases the semiconducting properties of the resulting MoS 2 [37].

Bottom-Up Methods
The chemical vapor deposition (CVD) method enables a controllable route to decompose Mo and S precursors and assemble them into nanosheets [10]. The MoS 2 nanosheets obtained by CVD are thin, of high quality and high purity, and present limited defects as 2D materials [90]. This method is also indicated for producing SLMoS 2 in large quantities at a low cost. However, it presents low control in terms of target products [91] and lacks good reproducibility since it depends on various parameters, such as temperature, pressure, and reaction time, among others [81]. The possibility of forming both SLMoS 2 and FLMoS 2 zones is also a limitation.
An alternative bottom-up approach that is frequently used is the hydrothermal method. In this method, the MoS 2 crystallizes from aqueous or organic solutions processed at high pressure and temperature [10]. This method achieves high yield, controllable size, and uniform thickness [10]. Although the hydrothermal method is widely used, the mechanism is unclear as the reaction occurs in a closed environment, an autoclave [10]. Different precursors can be used in this method. Khabiri et al. [92] used the hydrothermal method to prepare composites containing MoS 2 nanoflower structures, consisting of adding ammonium molybdate, thiourea, and water to an autoclave and setting the temperature to 180 • C for 20 h. Other authors used a similar procedure, but added ammonium tetrathiomolybdate, ethanol, and water to an autoclave heated at 200 • C for 10 min [93].
In the hydrothermal method, the morphology and properties of MoS 2 can be modified by adjusting the experimental synthesis conditions. Luo et al. [83] observed different morphologies, depending on the S:Mo molar ratio of the starting materials of molybdenum oxide (MoO 3 ) and potassium thiocyanate (KSCN). Low ratios led to the formation of nano-flower structures (Figure 3a), while at higher ratios (Figure 3b), only nanosheet structures were observed. The temperature and time of the synthesis can also influence the morphology. It was found that at a lower temperature (150 • C) for 25 h, the resulting morphology was like a coral ( Figure 3c); when increasing either the time or temperature, the dominant morphology was a flower-like structure (Figure 3d), with size increasing over the synthesis time. At higher temperatures and longer reaction times (240 • C for 47 h), the observed structure consisted of large nanosheets, showing the largest surface area. Other structures, such as core-shell or hollow structures, have been produced, aiming increasing over the synthesis time. At higher temperatures and longer reaction times °C for 47 h), the observed structure consisted of large nanosheets, showing the lar surface area. Other structures, such as core-shell or hollow structures, have produced, aiming to enhance the properties of MoS2 [94,95]. Wu et al. [95] produced 2 diameter hollow MoS2 microspheres via the hydrothermal method and used this mat to adsorb the organic contaminant, methyl orange.

MoS2 Modification Methods
The properties of MoS2 can be modified by expanding the interlaying spacin strategy that has been applied in the fields of batteries and photocatalysis [96]. Ai e [97] produced a widened defect-rich nano MoS2 (W-DR-N-MoS2) via the hydrothe method to adsorb mercury (Hg 2+ ). The interlayer spacing could be controlled by synthesis temperatures. The produced MoS2 consisted of layers of MoS2 with a w space between them (d = 9.4 Å against d = 6.15 Å for MoS2 powder); empty spaces in layers also characterized this material. Both aspects improved the adsorption capab by enabling adsorption between the layers.
The combination of MoS2 with other components can lead to materials improved adsorption capacity. For example, kaolin was used as a substrate for M growth via the hydrothermal method. The resulting composite showed increased volume, a larger number of adsorption sites, and a consequently greater Pb(II) adsorp efficiency than their counterparts [98]. On the other hand, using montmorillonite (M decreased the hydrophobicity of MoS2, increasing the dispersibility in water improving the adsorptive removal of Hg(II) [99]. The growth of Fe3O4 nanoparticles MoS2 nanosheets resulted in MoS2 composites with enhanced conductivity and mag behavior [100,101].
Doping MoS2 with heteroatoms can also modify the MoS2 properties by regula the electronic structure and conductivity, regulating the interlaying spacing, increasing the number of active sites [102][103][104]. This type of modification has been sh to be effective in photocatalytic hydrogen production and battery fields [102][103][104]. Do with metallic elements may lead to undesirable consequences, such as the reductio stability of MoS2 by promoting the formation of the MoS3 phase. In contrast, using

MoS 2 Modification Methods
The properties of MoS 2 can be modified by expanding the interlaying spacing, a strategy that has been applied in the fields of batteries and photocatalysis [96]. Ai et al. [97] produced a widened defect-rich nano MoS 2 (W-DR-N-MoS 2 ) via the hydrothermal method to adsorb mercury (Hg 2+ ). The interlayer spacing could be controlled by the synthesis temperatures. The produced MoS 2 consisted of layers of MoS 2 with a wider space between them (d = 9.4 Å against d = 6.15 Å for MoS 2 powder); empty spaces in the layers also characterized this material. Both aspects improved the adsorption capability by enabling adsorption between the layers.
The combination of MoS 2 with other components can lead to materials with improved adsorption capacity. For example, kaolin was used as a substrate for MoS 2 growth via the hydrothermal method. The resulting composite showed increased pore volume, a larger number of adsorption sites, and a consequently greater Pb(II) adsorption efficiency than their counterparts [98]. On the other hand, using montmorillonite (MMT) decreased the hydrophobicity of MoS 2 , increasing the dispersibility in water and improving the adsorptive removal of Hg(II) [99]. The growth of Fe 3 O 4 nanoparticles onto MoS 2 nanosheets resulted in MoS 2 composites with enhanced conductivity and magnetic behavior [100,101].
Doping MoS 2 with heteroatoms can also modify the MoS 2 properties by regulating the electronic structure and conductivity, regulating the interlaying spacing, and increasing the number of active sites [102][103][104]. This type of modification has been shown to be effective in photocatalytic hydrogen production and battery fields [102][103][104]. Doping with metallic elements may lead to undesirable consequences, such as the reduction in stability of MoS 2 by promoting the formation of the MoS 3 phase. In contrast, using nonmetallic elements promotes an increased number of active sites and conductivity [103]. Xin et al. [102] synthesized P-doped MoS 2 for photocatalytic hydrogen production. P-doped MoS 2 exhibited broader spectra absorption and a hydrogen production rate 2.8 times higher than the MoS 2 counterpart. Phase engineering is an approach in which several phases are combined to obtain optimal MoS 2 properties. As mentioned above, a combined 1T/2H phase achieved better results in the photodegradation of methyl orange due to the increased conductivity of the 1T phase and the defects present in this phase [69]. An identical MoS 2 phase combination was used in the photodegradation of potassium hexyl dithiocarbonate, which is an organic pollutant in mine wastewater [105].
An alternative strategy to modify the MoS 2 properties is defect engineering, which consists of creating defect sites in MoS 2 layers to act as active sites for catalysis [69,97]. Luo et al. [106] produced MoS 2 with S defects using a ball-milling method in ascorbic acid, an organic acid-reducing agent. The resulting S defect-rich ultrathin MoS 2 nanosheets were used to photo-reduce Cr(VI). This procedure leads to the formation of two types of S-defects: point defects that may act as recombination centers for photogenerated carriers, and stripping defects that promote the separation of photogenerated electron-hole pairs. According to the authors, combining both types of defects led to an enhancement of photocatalytic performance.
In the normal MoS 2 , only the edges sites have active regions with catalytic activity. One way to enhance this property is via the construction of vertically oriented MoS 2 nanosheets (V-MoS 2 ), which exhibit higher amounts of edge sites, enhanced longitudinal in-plane carrier transport, and stronger light adsorption [107,108]. Liu et al. [107] produced V-MoS 2 by means of CVD induced by a TiO 2 buffer layer, for application in photodetectors. Cui et al. [108] successfully applied a vertical growth MoS 2 construction method in graphene sheets to increase the electrochemical performance of lithium-sulfur batteries.

Adsorption Applications
This section reviews the application of MoS 2 -based nanomaterials to clean up emerging pollutants from water using adsorptive technologies. Table 1 provides an overview of several MoS 2 -based nanomaterials investigated for the adsorption of inorganic and organic contaminants.

Heavy Metal Species
Pollution with heavy metal species is a huge concern because it represents a high risk for the environment and for humans [8]. Heavy metal ions are toxic, non-biodegradable, persistent in the environment, and tend to accumulate in organisms, causing health issues [8]. Lead (Pb(II)) is one of the most common ions found in industrial wastewater and shows toxicity, even at low concentrations (≥15 µg/L in drinking water) [8]. Many problems, such as anemia, hypertension, reduced intelligence quotient, and immunotoxicity are related to Pb(II) exposure [8]. Mercury is another heavy metal that presents a high risk to human health and may cause kidney failure, severe pulmonary irritation, neurological disorders, and death [73]. Mercury exists in the form of several inorganic (e.g., metallic mercury or mercuric salts (Hg(II)) and organometallic species (e.g., methylmercury). The Hg(II) species can also affect the food chain once they can bioaccumulate [73]. Chromium, particularly chromium (VI), is hazardous to human health as well [112]. In this oxidation state, Cr(VI) can cause cancer and fetal malformations with only a concentration higher than 0.10 mg/L in drinking water [112].
As stated above, MoS 2 has good adsorption capability for heavy metal ions due to the sulfur atoms on the surface. For this reason, MoS 2 has been investigated in terms of the adsorptive removal of these pollutants from water. Table 1 lists the most relevant studies. Most of the studies focused firstly on Hg(II) removal, due to its high toxicity, and, secondly, on Pb(II) and Cr(VI) removal. For instance, Pirarath et al. [73] produced nanosheets of MoS 2 via surfactant-assisted hydrothermal synthesis, using sodium dodecyl sulfate (SDS), and investigated the adsorption of Hg(II) in batch conditions. The negative charge of the S layers increased with SDS, which induced an electrostatic interaction between Hg(II) and MoS 2 . A higher adsorption capacity was achieved due to the excess negative charge of the S layer, compared to the nanosheets of MoS 2 produced by other methods. Within 300 min, 0.5 g/L of the composite enabled 93% removal of Hg(II) in distilled water samples. Ai et al. [97] produced a widened defect-rich nano MoS 2 (W-DR-N-MoS 2 ), with many sulfur binding sites exposed due to enlarged interlayer spacing. With this modification, Hg(II) removal of 99.8% was achieved in just 5 min in distilled water samples, using 0.1 g/L of the material. The Hg(II) removal was also efficient in both natural water and industrial wastewater samples. The recovery of the adsorbent is economically important. Coupling a magnetic component to MoS 2 has been investigated as a strategy to facilitate its separation; employing a magnetic field is an accessible method. Zhi et al. [109] produced an aerogel of MoS 2 and GO with embedded Fe 3 O 4 and Au NPs (Au/Fe 3 O 4 /MoS 2 CAs) to remove Hg(II). A removal performance of 100% was achieved in only 30 min with 0.5 g/L of Au/Fe 3 O 4 /MoS 2 CAs, which is a great achievement for Hg(II) adsorption. The reuse of this composite for up to 10 cycles only slightly decreased the efficiency of the adsorption. Wang et al. [111] used flower-like MoS 2 decorated with Fe 3 O 4 to investigate the simultaneous removal of Hg(II) and Pb(II) from distilled water, along with Pb(II) removal in real battery wastewater and soil samples, achieving satisfactory results. Yuan et al. [98] produced a MoS 2 -kaolin composite for Pb(II) adsorption, reaching a 99.9% removal rate in 40 min with 1.6 g/L of composite. According to the authors, using kaolin induces uniform MoS 2 growth and a higher pore volume, leading to more adsorption sites. Regarding the Cr(VI) removal, Chen et al. [112] produced MoS 2 /lignin-derived carbon (MoS 2 /LDC) and achieved 99.4% removal of Cr(VI) in distilled water samples after 30 min, using just 0.10 g/L of composite.
It is essential to evaluate the selectivity of the adsorbents toward the target pollutant because in natural water or wastewater, there are other species that can compete for sorption sites. In this context, Zhi et al. [109]  The reason for this selectivity may be related to the HSAB principle, i.e., soft acids such as Hg(II) establish strong interactions with soft bases such as sulfur [111,115].
After adsorption tests, the composite with the adsorbed heavy metal ion can be separated from the solution and treated, aiming for a reduction in the heavy metal ions, which precipitate and desorb from the catalyst [111,112].
Besides the heavy metal species, MoS 2 -based materials have been employed for the capture of noble metal species, namely, silver and gold ions. The recovery of these metals from industrial effluents and wastewater is important, not only to prevent pollution but also because of their economic value [28,74]. Zeng et al. [74] produced a 2D MoS 2 to remove Ag(I) from distilled water samples. The mechanism of adsorption was investigated using Xray photoelectron spectroscopy (XPS) and DFT calculations, confirming a strong interaction between MoS 2 and Ag(I) by the complexation of Ag-S and Ag-O through hybridization between the d orbital of Ag and the p orbital of S or O [74]. The recovery of gold ions (Au(III)) has also been investigated [28]. Using chitosan-coated MoS 2 (0.28 g/L dose), Zhao et al. [28] achieved 98.9% ion removal in 300 min. The ion-selectivity of chitosancoated MoS 2 in wastewater containing Au(III), Cu(II), Mg(II), Ni(I), Li(I), and Zn(II) species was evaluated. It was found that the biosorbent presented the highest selectivity to the Au(III) ions and the lowest affinity to Zn(II) ions. After adsorption, desorption enabled the recovery of noble metal ions for further use.

Organic Contaminants
The adsorption of organic contaminants using MoS 2 -based materials was less widely investigated. MoS 2 -based membranes for organic contaminant removal are beyond the scope of this work and have recently been reviewed elsewhere [13]. Most research papers that present results of the adsorption of organic contaminants have, as their primary focus, the study of the photodegradation of these contaminants. Table 1 lists several studies of the adsorption of organic contaminants. MoS 2 nanosheets produced by the hydrothermal method removed nearly 82.3% of Bisphenol A (BA), which is an endocrine disruptor, after 120 min with a sorbent dosage of 1.5 g/L [83]. Reduced graphene oxide-MoS 2 (rGO-MoS 2 ) composites successfully removed the ofloxacin antibiotic [7]. Despite the low surface area (17 m 2 /g), 95% removal was achieved after 240 min with 0.35 g/L of adsorbent. The adsorption capacity in real wastewater samples was also investigated. However, the removal drastically decreased after composite reuse, and only 4% was removed after 10 cycles. Gao et al. [113] produced a composite with a metal-organic framework (UiO-66/MoS 2 ) and report a comprehensive study on the adsorption and photocatalytic degradation of lomefloxacin. The beta-blockers, atenolol and acebutolol, were also adsorbed successfully in distilled water with MoS 2 /montmorillonite (MoS 2 /MTT) composites [114]. Regarding the adsorption of dyes, methyl orange was adsorbed by hollow MoS 2 microspheres (h-MoS 2 ) [95]. The adsorption equilibrium was achieved in just 10 s for MO, with a maximum adsorption capacity of 42 mg/g. MoS 2 -based composites have also been used for the adsorption of various organic dyes. Song et al. [100] produced MoS 2 decorated with Fe 3 O 4 nanoparticles and tested this composite for the adsorption of Congo red (CR), methylene blue (MB), methylene green (MG), rhodamine B (RhB) and eosin Y (EY). Among these dyes, the composite showed higher adsorption of CR with an adsorption capacity of 71 mg/g, achieving the removal of about 65.2% in 2 min, which increased to 71% after 120 min with 1 g/L of the composite. Table 1 presents a summary of relevant information on the kinetics and equilibrium adsorption tests employing MoS 2 -based materials. Overall, the kinetic model that better described the results was the pseudo-second-order (PSO) kinetic model, with an R 2 value of between 0.901-1.000, indicating a good fit of this model to the adsorption data of both the metal species and organic contaminants. Regarding the equilibrium description, the Langmuir model better described the adsorption data (R 2 = 0.86-1.0). However, the equi-librium adsorption of the antibiotic lomefloxacin and MO dye was better described by the Freundlich isotherm model, indicating non-monolayer formation [83,115]. Wang et al. [111] used flower-like MoS 2 decorated with Fe 3 O 4 nanoparticles in the removal of Hg(II) and Pb(II) from an aqueous environment. The maximum adsorption capacity estimated by the Langmuir model was 428.9 mg/g for Hg(II) and 263.6 mg/g for Pb(II), under optimized conditions (pH 5, 25 • C, 0.8 g L −1 sorbent dosage). The adsorption kinetics were well described by the PSO model and the good fitting of the Langmuir isotherm model was in line with monolayer formation. The favorable adsorption capacity, selectivity, and recyclability originated from the strong interaction between S and the heavy metal ions. The MoS 2 -clinoptilolite composite removed nearly 100% (99.8%) of Pb(II) from aqueous solution (pH 6, 25 • C, starting concentration of 50 mg L −1 , 1.5 g L −1 sorbent dosage) after 90 min [8]. This adsorption was ascribed to the interaction of Pb(II), not only with the S layers of the MoS 2 but also with the -OH and -COOH functional groups of clinoptilodite. The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic in nature.

Kinetic and Isotherm Studies
Looking at the equilibrium adsorption values (qe) of the metal species in Table 1, the highest value found was 3435 mg/g (R 2 = 0.991) for the adsorption of Au(III) at an optimal pH of 5, using chitosan-coated MoS 2 (CS/MoS 2 ) crosslinked with glutaraldehyde. The value was estimated by the Langmuir model and was close to the experimental value (3109 mg/g) [28]. The adsorption capacity increased and the adsorption isotherm changed from multilayer to monolayer when the content of MoS 2 increased. The highest adsorption capacity was observed for a mass ratio of 1:2 (CS:MoS 2 ), at 35 • C, after 300 min. The high efficiency of these materials to adsorb Au(III) was ascribed to electrostatic interaction, in the form of tetrachloroaurate ions (AuCl 4 -) and then to complexation by the sulfur-and nitrogen-containing functional group. The materials also showed outstanding selectivity for gold ions in the presence of coexisting ions and demonstrated attractive reusability after four cycles.
Concerning the organic contaminants, the highest adsorption capacity was observed for atenolol, using MoS 2 /MTT as an adsorbent (qe = 146 mg/g) and close to the value estimated by the Langmuir model (132 mg/g) [114]. The adsorption kinetics could be described using the PSO model. The interactions leading to the adsorption included van der Waals interactions and hydrogen bonding between the hydroxyl groups of the atenolol and the sorbent. The quantum chemical calculations results were in line with the lower adsorption capacity observed for acetobutolol using the same adsorbent.
Other parameters and isotherm models have been used to characterize the adsorption, such as the distribution coefficient, which expresses the affinity of a compound to the adsorbent, and Temkin isotherm, which assumes that the heat of adsorption does not remain constant during the adsorption process [74,110].

Photocatalytic Applications
Adsorption is an excellent approach to removing pollutants from wastewater. However, this technique does not provide a complete solution to the problem since the contaminants are not mineralized. In this sense, advanced oxidation processes (AOPs), such as photocatalytic oxidation, have been developed to promote the degradation of pollutants [116].
Due to the relatively small band gap of MoS 2 , visible-light irradiation can induce a catalytic chain reaction. For bulk MoS 2 , the band gap is~1.2 eV, which means that MoS 2 is activated with almost all the solar spectrum, while SLMoS 2 shows a band gap of~1.8 eV, this phase being activated by a radiation wavelength of <660 nm. However, as the bulk MoS 2 has unsaturated Mo and S atoms at the edge, leading to an indirect and small band gap, this is insufficient to achieve photocatalytic reactions. For this reason, bulk MoS 2 is not suitable for photocatalysis [117]. MoS 2 has been combined with several components to improve its performance as a photocatalyst to degrade contaminants. Table 2 lists several recent studies on the photo-catalytic degradation of pollutants in water. MoS 2 -based materials have been primarily employed in the photodegradation of dyes. Dye-related industries are reported as the major source of contaminated wastewater [118]. Dye-containing wastewater presents both chromaticity and toxicity [25,119]. Pharmaceuticals, antibiotics, and pesticides, among other chemical compounds, also represent emerging contaminants where photodegradation has been investigated, due to their toxicity and increasing detection in wastewater [119]. The same photocatalyst could photodegrade various contaminants at different rates. For example, Fu et al. [120] reported degradation rates above 70% for methylene blue (MB), methyl orange (MO), and Congo red (CR), using ZnO/MoS 2 nanoarrays. In contrast, the degradation of rhodamine B (RhB) dye was only around 8%. Regarding the degradation of MB, Khabiri et al. [92] achieved 83% degradation after 1 min of irradiation with VIS light, that increased to 91% after 120 min using α-Fe 2 O 3 /MoS 2 QDs, a composite comprising hematite (α-Fe 2 O 3 ) and nanosized MoS 2 (MoS 2 quantum dots (QDs)). Figure 4 illustrates the proposed photocatalytic mechanism. The visible light irradiation excites the electrons (e − ) in the valence bands (VB) of α-Fe 2 O 3 and MoS 2 QDs to the respective conduction bands (CB), leaving a hole (h + ) in the VB. The CB and VB positions of MoS 2 QDs are above α-Fe 2 O 3 . Due to the potential energy difference, the photogenerated electrons at the CB of MoS 2 QDs transfer to the CB of α-Fe 2 O 3 , then migrate to the surface of the catalyst, which enables the creation of the reactive species as a superoxide anion radical (·O 2 − ) by the reaction with O 2 , and hydroxyl radicals (·OH) from reaction with water. The reactive species react with MB, thereby degrading it [92]. Most of the values for the degradation rate presented in Table 2 are above 70% for different contaminants, MoS 2 -based catalysts, and methodologies. For MB, the highest degradation rate was 97%, after 40 min of reaction using 1 g/L of MZO (MoS 2 /ZnO) [121]. A similar degradation rate was obtained in just 5 min using the ternary catalyst MoS 2 /BiFeO 3 /Ag 3 PO 4 under ultraviolet-visible (UV-Vis) irradiation [119]. The same catalyst achieved a good degradation of MO and RhB, with 98% and 97% degradation, respectively, after 5 min of irradiation (Table 2) [119]. Regarding other contaminants from the antibiotic spectrum, tetracycline (20 mg/L) was successfully degraded up to 99% within 50 min under visible light, catalyzed with 0.4 g/L MoS 2 /Eu/Bg-C 3 N 4 (MoS 2 /BEuCN) as the catalyst [122]. Ahamad et al. [123] studied the photocatalytic degradation of bisphenol-A (BA) using the composite g-C 3 N 4 /MoS 2 −PANI, achieving 93% of removal after 60 min under visible light. DFT calculations were performed to elucidate the photocatalytic degradation mechanism of BA. It was proposed that the aromatic ring would be one of the most likely sites for an attack by photo-generated radicals, which leads to several intermediate species and to the production of the final products, CO 2 and H 2 O [123].     Although most photodegradation studies rely on organic contaminants, MoS2-based photocatalysts were also employed to reduce Cr(VI) to Cr(III) [120,134]. As mentioned before, Cr(VI) is a highly toxic form of chromium. By reducing it to Cr(III), the toxicity decreases, and the chromium can be precipitated and removed [144]. Via photo-reduction, 85% Cr(VI) removal was achieved using MoS2/BiOBr/CF under visible light after 2 h, and 75% Cr removal rate using Ni foam with ZnO/MoS2 after 25 min under UV-VIS light [120,134]. Shi et al. [134] tested the effect of pH in this photocatalytic reaction and observed the highest removal (91%) at pH = 3 and the lowest removal (29%) at pH = 11. This behavior was ascribed to different chromium speciation according to pH. At pH < 7, the predominant species is the dichromate anion (Cr2O7 2− ), which is more likely to be reduced to Cr(III) than the chromate anion (CrO4 2− ), which predominates at pH > 7. In addition, using MoS2/TiO2/graphene, Chen et al. [137] achieved an 88% removal of Pb(II) in an aqueous solution in just 60 min under UV-Vis light. The removal was higher in an acidic environment (pH < 7) because the dominant species at those pH values (Pb 2+ (H2O)6) is more reactive than the other Pb(II) species, due to the more positive charge and smaller hydration radius.
In photocatalysis, the goal is to achieve the total mineralization of the pollutants. This means fully converting the contaminants to a gaseous form, water, salts, and minerals [145]. However, several photodegradation reactions may lead to toxic intermediate compounds, which can harm the environment [146]. The total organic carbon (TOC) quantification method can be employed to evaluate the mineralization of a contaminant achieved by photocatalysis. Table 3 shows a relatively high mineralization rate, with more than 54% of the mineralization provided by MoS2-based photocatalysts. This means that most of the contaminant molecules present in the solution (>50%) were fully degraded, while part may still be the original contaminant (when the removal rate is less than 100%) or is converted into some intermediate compound. For example, 100% degradation of Rhodamine B was achieved with the BiOI/MoS2 (BMS-8) catalyst. However, only 78% of the initial amount of the dye was fully mineralized, leaving 23% in the form of Although most photodegradation studies rely on organic contaminants, MoS 2 -based photocatalysts were also employed to reduce Cr(VI) to Cr(III) [120,134]. As mentioned before, Cr(VI) is a highly toxic form of chromium. By reducing it to Cr(III), the toxicity decreases, and the chromium can be precipitated and removed [144]. Via photo-reduction, 85% Cr(VI) removal was achieved using MoS 2 /BiOBr/CF under visible light after 2 h, and 75% Cr removal rate using Ni foam with ZnO/MoS 2 after 25 min under UV-VIS light [120,134]. Shi et al. [134] tested the effect of pH in this photocatalytic reaction and observed the highest removal (91%) at pH = 3 and the lowest removal (29%) at pH = 11. This behavior was ascribed to different chromium speciation according to pH. At pH < 7, the predominant species is the dichromate anion (Cr 2 O 7 2− ), which is more likely to be reduced to Cr(III) than the chromate anion (CrO 4 2− ), which predominates at pH > 7. In addition, using MoS 2 /TiO 2 /graphene, Chen et al. [137] achieved an 88% removal of Pb(II) in an aqueous solution in just 60 min under UV-Vis light. The removal was higher in an acidic environment (pH < 7) because the dominant species at those pH values (Pb 2+ (H 2 O) 6 ) is more reactive than the other Pb(II) species, due to the more positive charge and smaller hydration radius.
In photocatalysis, the goal is to achieve the total mineralization of the pollutants. This means fully converting the contaminants to a gaseous form, water, salts, and minerals [145]. However, several photodegradation reactions may lead to toxic intermediate compounds, which can harm the environment [146]. The total organic carbon (TOC) quantification method can be employed to evaluate the mineralization of a contaminant achieved by photocatalysis. Table 3 shows a relatively high mineralization rate, with more than 54% of the mineralization provided by MoS 2 -based photocatalysts. This means that most of the contaminant molecules present in the solution (>50%) were fully degraded, while part may still be the original contaminant (when the removal rate is less than 100%) or is converted into some intermediate compound. For example, 100% degradation of Rhodamine B was achieved with the BiOI/MoS 2 (BMS-8) catalyst. However, only 78% of the initial amount of the dye was fully mineralized, leaving 23% in the form of intermediate compounds [3]. Overall, the results show the promising potential of MoS 2 -based catalysts to photodegrade and mineralize the organic contaminants in wastewater systems. Note: 2,4-D-2,4-dichlorophenoxyacetic acid; CF-carbon fiber; MB-methylene blue; MO-methyl orange; RhB-rhodamine B; TC-tetracycline; * TOC after 60 min of irradiation; ** TOC after 7 h of irradiation.

MoS 2 -Based Nanocomposites
Although nano-MoS 2 shows good efficiency as a photocatalyst for removing several contaminants, it can be enhanced when in combination with other components in the form of nanocomposites. Table 4 lists several works comparing the photodegradation provided by bare nano-MoS 2 and MoS 2 -based nanocomposites. Overall, MoS 2 -based nanocomposites present a higher specific area when compared to bare nano-MoS 2 . The increase in the specific surface area of the catalyst can contribute to an enhanced removal rate once a higher exposed specific area favors the contaminant-catalyst contact [142].
Overall MoS 2 -based composites presented better adsorptive performance than bare MoS 2 . The creation of defects and increasing interlayer spacing were used to enhance the adsorption capacity of Hg(II) from 36 mg/g to 2563 mg/g [97]. The introduction of montmorillonite (MMT) enhanced the water dispersibility of MoS 2 by decreasing the hydrophobicity, which improved the adsorption capacity [99]. For instance, MoS 2 /MMT composites adsorbed nearly 1120 mg/g of Hg(II), which is markedly higher than the value observed for bare MoS 2 (937 mg/g). MoS 2 /MMT composite was also used to adsorb the beta-blockers atenolol and acebutolol, achieving good results [114]. Kaolin has been used as a substrate, providing a uniform growth of MoS 2 and well-distributed active sites, which improved the removal of Pb(II) from 55% in bare MoS 2 to 89% in MoS 2 -kaolin [98].  The combination of MoS 2 with semiconducting phases has been explored, to improve photocatalytic activity. Quan et al. [121] coupled MoS 2 nanoflowers to ZnO nanoparticles and observed a considerable increase in the degradation rate of methylene blue compared with bare MoS 2 , from 44% to 97%, when submitted to visible light (λ > 420 nm). Introducing the semiconductor ZnO resulted in an increased photoinduced electron transfer rate, leading to higher photocatalytic activity. ZnO also presents attractive characteristics, such as low cost, low toxicity, high chemical stability, and strong photosensitivity [121]. Mahalakshmi et al. [127] produced core@shell TiO 2 @MoS 2 heterojunction composites via the one-step hydrothermal method. The photocatalytic activity of the resulting composite toward 4-nitrophenol was enhanced compared to the MoS 2 and TiO 2 used separately, due to a reduced band gap and efficient separation of the photogenerated electron-hole pairs. A similar strategy was reported for coupling MoS 2 and CuO, with improved separation of electron-hole pairs [142]. A Z-scheme heterojunction was produced that promoted the separation of the photogenerated carriers and may also increase the specific area and, consequently, the number of active sites [142]. BiOI nanoplates were also combined with MoS 2 nanosheets [3]. ZnS was combined with MoS 2 to increase the efficiency of photocarrier generation, increasing the removal of crystal violet dye using visible light (λ > 420 nm) [132]. Composites of MoS 2 with UiO-66 resulted in an enhanced specific area and in more active sites being available [113]. Several studies report the incorporation of magnetic nanostructures (e.g., magnetite-Fe 3 O 4 ) to enhance the photocatalytic activity of MoS 2 [25,135]. This approach facilitates the separation of the nanocatalyst from the treated solution and increases the efficiency of the transport of photogenerated electrons, leading to a higher removal rate, even in the case of a lower specific area compared to bare MoS 2 [25].

Reuse of MoS 2 -Based Composites for Adsorption and Photocatalysis
After interacting with the contaminated solution, the catalysts and adsorbents should then be collected and reused to reduce the quantity of produced materials and the associated costs. Importantly, the composite should maintain good adsorption/photoactivity when reused. Reusability studies have been performed to verify the efficiency of the composite after several cycles. At the end of each removal experiment, the sorbent/photocatalyst is collected through centrifugation or filtration and is washed off with water and ethanol or water alone, and then dried [121,124]. In this context, magnetic nanomaterials are advantageous because they are easily recovered using magnetic separation, which requires less energy [25,100,111,135]. Table 5 compares the evolution of the degradation rate via adsorption and photodegradation after several testing cycles. The MoS 2 -based composites showed good adsorption when comparing the first and the last cycles [99,[110][111][112]. The Au/MoS 2 composites also presented good adsorption after four consecutive cycles in a solution containing multiple ions, demonstrating their great potential for heavy metal ion removal [28]. Zhi et al. [109] reported a removal rate of > 95% after 10 reusing cycles for the adsorption of Hg(II). Several other studies report minor differences in adsorption capacity at the first and last adsorption cycles, regardless of the contaminant. Conversely, a marked decrease in the adsorption of the antibiotic ofloxacin was observed when the rGO-MoS 2 composite was reused [7]. The removal decreased from 92% to just 4% after 8 cycles, but the authors do not offer a possible explanation [7].
The reuse of MoS 2 -based photocatalysts has also been investigated. However, often, the papers do not give detailed results of the reuse studies. Overall, the photocatalyst maintains good photocatalytic activity after several cycles. Yet, in some cases, significant decreases in the photodegradation rate were observed due to the oxidation of the photocatalyst [126].

Application of MoS 2 -Based Composites in Real Environmental Samples
So far, most studies have only focused on treating singular contaminant solutions in synthetic aqueous samples. The number of reports testing MoS 2 and composites in water decontamination in more realistic conditions is still scarce. MoS 2 /Fe 3 O 4 composite was employed as an adsorbent to treat effluents from lead-acid battery factories, reaching a Pb(II) removal of 99.6% and showing acceptable Pb(II) removal in contaminated soil [111]. Regarding the adsorption of organic contaminants, Zeng et al. [147] used MoS 2decorated biochar to remove the antibiotic tetracycline hydrochloride from river and tap water. The adsorption capacity was found to be higher in environmental water samples when compared to synthetic solutions, prepared in deionized water and used under the same conditions. Furthermore, the composite could be reused for 5 cycles with only a minor decrease in the adsorption capacity. Conversely, the adsorption capacity of the antibiotic ofloxacin by the rGO-MoS 2 composites in river water was lower than in deionized water [7]. The effect was ascribed to the presence of cations, natural and synthetic organic chemicals that compete with ofloxacin for adsorption, leading to a decrease in the adsorption capacity. Huang et al. [148] realized that the photocatalytic activity of MoS 2 microspheres in degrading thiobencarb in lake or river water decreased by 20% compared to its performance in spiked deionized water, under identical reaction conditions. The presence of anions in non-deionized water acting as scavengers was identified as a cause for the decrease in photocatalytic activity. Nevertheless, the authors considered this material a potential catalyst for removing pollutants. Chandrabose et al. [149] assessed the photocatalytic efficiency of MoS 2 /TiO 2 composite in a solution comprising a mixture of anionic dyes (rhodamine B and methyl orange) and cationic dyes (methylene blue and crystal violet). The composite removed 100% of cationic dyes and 70% of the anionic dyes in the first stage of adsorption in the dark, while the remaining 30% of anionic dyes were photodegraded entirely after 3.5 h in a second stage under UV-Vis light irradiation. The composite showed higher adsorptive affinity to the cationic dyes compared to anionic dyes. Increasing contaminant concentrations resulted in less adsorptive removal at the first stage, which was limited by the surface area of the composite. The results of the study show the potential of using this MoS 2 -based composite for the removal of dyes produced by textile industries.

Environmental Impact of MoS 2 -Based Composites
Water remediation studies employing MoS 2 -based composites have been focused on the evaluation and enhancement of the composites' removal capacity. The assessment of the ecotoxicity of the materials has been less widely investigated, although it is a fundamental matter. Nanomaterials have emerged as a promising tool for water remediation, but, due to their high surface area and chemical activity, if accidentally released into the environment, they may constitute a risk [150]. Depending on their chemical properties and composition, nanomaterials can be modified by oxidation, sulfidation, aggregation, and deposition in the natural environment [151]. In terms of the properties of nano-MoS 2 , this material is considered chemically stable even in environmental conditions [75]. Due to its low solubility in water systems, it is also considered a persisting compound. Nano-MoS 2 may persist in the environment and the actual risks are still unknown. The nanosheets of MoS 2 showed antibacterial activity against Escherichia coli and Staphylococcus aureus and low cytotoxicity for Vero cells [19]. Cicuendez et al. [152] also observed good viability of mouse and human cells when exposed to MoS 2 flakes. A more comprehensive study on the toxicity of bulk and MoS 2 nanosheets was conducted to address the toxicity in various aquatic species of different taxonomic groups [34]. The EC50 was determined for four species: Vibrio fischeri, a marine Gram-negative photobacterium, Pseudokirchnerialla subcapitata, a freshwater microalga, Daphnia magna, a freshwater crustacean, and Spirodela polyrhiza, a freshwater duckweed. Bulk and nano MoS 2 (0.05-2.00 g/L) were tested for a contact time ranging from 15 min to 72 h. It was found that bulk MoS 2 was more toxic than MoS 2 nanosheets for all the species tested; in some cases, nano MoS 2 showed no toxicity for the tested conditions.

Conclusions and Perspectives
In summary, this review highlights the advantages of MoS 2 and MoS 2 -based nanomaterials for water treatment applications through adsorption and photocatalysis. Owing to the high surface area and visible light-responsive photocatalytic activity, we can expect growing interest in these materials for environmental applications in the near future. Several advances have been made in synthetic methods for the production of MoS 2 nanomaterials with different structural features, namely, the crystal phase, morphology and layer spacing, which each create distinct physicochemical properties. The applications of MoS 2 and composites in the adsorption and photodegradation of metal ion species and organic contaminants are thoroughly summarized. The modification of MoS 2 and its combination with other components enhance those properties that increase removal efficiency and may also facilitate the separation of the catalyst from the solution. Despite the progress achieved, more studies are needed to rationally fabricate highly efficient MoS 2 -based photocatalysts, which represents an opportunity for further research efforts. The ecotoxicity of MoS 2 is still not clear and requires further investigation. Although MoS 2 presents high chemical stability, even in environmental aqueous systems, it also presents some toxicity to different organisms. More studies should be conducted to assess the risks of employing MoS 2 -based materials in water treatment.