Biopolymers-Derived Materials for Supercapacitors: Recent Trends, Challenges, and Future Prospects

Supercapacitors may be able to store more energy while maintaining fast charging times; however, they need low-cost and sophisticated electrode materials. Developing innovative and effective carbon-based electrode materials from naturally occurring chemical components is thus critical for supercapacitor development. In this context, biopolymer-derived porous carbon electrode materials for energy storage applications have gained considerable momentum due to their wide accessibility, high porosity, cost-effectiveness, low weight, biodegradability, and environmental friendliness. Moreover, the carbon structures derived from biopolymeric materials possess unique compositional, morphological, and electrochemical properties. This review aims to emphasize (i) the comprehensive concepts of biopolymers and supercapacitors to approach smart carbon-based materials for supercapacitors, (ii) synthesis strategies for biopolymer derived nanostructured carbons, (iii) recent advancements in biopolymer derived nanostructured carbons for supercapacitors, and (iv) challenges and future prospects from the viewpoint of green chemistry-based energy storage. This study is likely to be useful to the scientific community interested in the design of low-cost, efficient, and green electrode materials for supercapacitors as well as various types of electrocatalysis for energy production.


Scientific Stimulus
The generation of energy and its storage involving fossil fuels, as well as global warming, are closely related and contribute to significant environmental problems that threaten human existence. If these problems are not addressed soon, the survival of life on our planet will be in jeopardy for generations to come. Energy storage technologies such as batteries and supercapacitors will play a significant role in the power shift to zero or lower greenhouse gas emissions by connecting renewable energy production to suitable energy storage systems. These energy storage technologies may be used for electric vehicles, and it is expected that over 34 million various types of electric vehicles would be marketed by 2030 [1,2]. This suggests that supercapacitors and batteries have the potential to dramatically reduce greenhouse gas emissions in the electricity and transportation sectors, thereby contributing significantly to the accomplishment of Sustainable Development Goal 7 (clean and affordable energy). Renewable energy sources such as solar energy have The majority of natural biopolymers are chain-like molecules with repeated units, such as polysaccharides [22] (alginate, cellulose, chitosan, and chitin), proteins [23] (gelatin and silks), and others. Their abundance and excellent properties, such as low cost, biodegradability, renewability, non-toxicity, and textural properties, have encouraged the interest of scientists to investigate their chemical structure, physicochemical properties, and applications [15,24]. Natural biopolymers' structural properties, in addition to their inherent biological properties, make them great candidates for the synthesis of high-performance composites. As a result, the numerous functional groups (e.g., amine, amino, carboxyl, and hydroxyl groups) from polymer molecular chains endow biopolymers with high hydrophilicity, desirable for the construction of porous materials for energy storage. Furthermore, because of their high reactivity, these functional groups may be modified to fulfill the demands of many specialized functions by altering mechanical characteristics, capacity, crystal structure, electron transfer rates, and solubility as well [1,5,6]. All of the characteristics stated above emphasize the importance of natural biopolymers in the construction of high-performance supercapacitors. Figure 2 illustrates the systematic classification of green biopolymeric materials. This work will appeal to prospective readers The majority of natural biopolymers are chain-like molecules with repeated units, such as polysaccharides [22] (alginate, cellulose, chitosan, and chitin), proteins [23] (gelatin and silks), and others. Their abundance and excellent properties, such as low cost, biodegradability, renewability, non-toxicity, and textural properties, have encouraged the interest of scientists to investigate their chemical structure, physicochemical properties, and applications [15,24]. Natural biopolymers' structural properties, in addition to their inherent biological properties, make them great candidates for the synthesis of high-performance composites. As a result, the numerous functional groups (e.g., amine, amino, carboxyl, and hydroxyl groups) from polymer molecular chains endow biopolymers with high hydrophilicity, desirable for the construction of porous materials for energy storage. Furthermore, because of their high reactivity, these functional groups may be modified to fulfill the demands of many specialized functions by altering mechanical characteristics, capacity, crystal structure, electron transfer rates, and solubility as well [1,5,6]. All of the characteristics stated above emphasize the importance of natural biopolymers in the construction of high-performance supercapacitors. Figure 2 illustrates the systematic classification of green biopolymeric materials. This work will appeal to prospective readers including scientists, researchers, and academicians working in the realms of bio-polymers-based materials and manufacturing of effective electrode materials for supercapacitors. including scientists, researchers, and academicians working in the realms of bio-polymers-based materials and manufacturing of effective electrode materials for supercapacitors.

Scope of this Review
This review emphasizes the comprehensive concepts of biopolymers and their synthesis for supercapacitors' applications. Various synthesis strategies for biopolymer derived nanostructured carbons and their corresponding structure variations have been discussed. Challenges and future prospects from the viewpoint of green chemistry-based energy storage have been highlighted. This study is likely to be useful to the scientific community interested in the design of low-cost and efficient electrode materials for supercapacitors as well as various types of electrocatalysis for energy production.

Synthesis of Biopolymeric Materials for Supercapacitors
Various synthesis processes such as electrospinning, hydrothermal carbonization (HTC), microwave-assisted activation, sol-gel, and templating have been employed to create biopolymer-based materials for supercapacitor applications. Additional discussions in subsequent sections covers the usage of green biopolymeric materials to prepare hierarchical porous materials for supercapacitors.

Pyrolysis
Pyrolysis is a thermal synthesis technique that happens in the absence, or with a limited fraction, of oxidizing gas, avoiding further oxidation reactions and thereby suppressing carbon dioxide formation. This allows for many reactions, and biopolymeric components are broken down into smaller units. Different products are produced as a result of these reactions. It is critical to highlight that biochar is primarily obtained through biopolymer conversion [11].

Scope of this Review
This review emphasizes the comprehensive concepts of biopolymers and their synthesis for supercapacitors' applications. Various synthesis strategies for biopolymer derived nanostructured carbons and their corresponding structure variations have been discussed. Challenges and future prospects from the viewpoint of green chemistry-based energy storage have been highlighted. This study is likely to be useful to the scientific community interested in the design of low-cost and efficient electrode materials for supercapacitors as well as various types of electrocatalysis for energy production.

Synthesis of Biopolymeric Materials for Supercapacitors
Various synthesis processes such as electrospinning, hydrothermal carbonization (HTC), microwave-assisted activation, sol-gel, and templating have been employed to create biopolymer-based materials for supercapacitor applications. Additional discussions in subsequent sections covers the usage of green biopolymeric materials to prepare hierarchical porous materials for supercapacitors.

Pyrolysis
Pyrolysis is a thermal synthesis technique that happens in the absence, or with a limited fraction, of oxidizing gas, avoiding further oxidation reactions and thereby suppressing carbon dioxide formation. This allows for many reactions, and biopolymeric components are broken down into smaller units. Different products are produced as a result of these reactions. It is critical to highlight that biochar is primarily obtained through biopolymer conversion [11].
The process factors, such as residence temperature and heating rate, influence the final carbon material generated from biopolymers. Temperatures between 600 and 900 • C are the most favorable for producing biochar suitable for supercapacitors. The pyrolysis of biopolymers is not a one-step process. Dehydration, heat degradation, and the formation of a stable carbon structure are usually the first three phases [10]. The pyrolysis process involves synthesizing carbon material from biopolymers to form a large surface area and high porosity. Yang et al. [25] created a porous regenerated cellulose aerogel by dissolving cellulose fibers in a NaOH/urea aqueous solution. The activated RCA-activated carbon aerogel was utilized as an electrode after pyrolysis and activation and displayed a high specific capacitance of 381 F/g in an aqueous electrolyte of 6 M KOH. The carbon aerogel electrode also had a low equivalent series and a low charge transfer resistance, indicating superior capacitive behavior.
Zhuo et al. [26] prepared a porous carbon aerogel as a substrate for the conductive polymer PPy using cellulose as a carbon precursor. The hierarchical porous structure allows for efficient PPy penetration and uniform loading across the carbon network. It ensures quick electrolyte ion transport and PPy accessibility. The synthesized electrode exhibits a high specific capacitance of 388 F/g in 1 M H 2 SO 4 and excellent cyclic stability, with 93% capacitance retention after 10000 cycles.
The pyrolysis technique increases surface area and porosity, which improves energy storage capacity. Although classic carbonization-activation procedures can produce porous carbons with adjustable SSAs and pore-size distributions, the templates or residues of activation agents must be eliminated after carbonization and activation. As a result, approaches that do not require activation are becoming increasingly appealing. The dehydration and decomposition processes in typical pyrolysis processes of biopolymeric materials result in the emission of gases (e.g., H 2 O, CO 2 , NH 2 , and CO), where the pyrolysis gases function as porogen. The SSA and pore-size distribution of generated carbon material can be finely controlled for supercapacitor use by manipulating pyrolysis parameters such as carbonization temperature, heat ramping rate, and carbonization time.

Electrospinning
It is a straightforward way to make polymer nanofibers using high voltage [27]. This approach may be used to create fibers from organic polymers while integrating graphene, metal oxides, carbon nanotubes, and other nanomaterials' [28][29][30] converted cellulose acetate (CA) into porous carbon nanofibers in one step. The electrospun fibers were carbonized and activated in a single process by immersing them in a ZnCl 2 solution and heating them ( Figure 3).  The activation process compressed micropores, lowering the quantity and expanding the pores. The resulting nanofibers with pore sizes of 0.6 to 1.2 nm, and 1188 m 2 /g active surface area were stable thermally and mechanically. Supercapacitors constructed from the nanofibers showed a high specific capacitance of 202 F/g at 0.1 A/g and constant cyclic  The activation process compressed micropores, lowering the quantity and expanding the pores. The resulting nanofibers with pore sizes of 0.6 to 1.2 nm, and 1188 m 2 /g active surface area were stable thermally and mechanically. Supercapacitors constructed from the nanofibers showed a high specific capacitance of 202 F/g at 0.1 A/g and constant cyclic performance of 92% after 5000 cycles, demonstrating strong electrochemical stability and reversibility. In another recent study, Wang et al. [29] used electrospinning, regeneration, and carbonization to produce nitrogen-doped carbon nanofibers from cellulose acetate and soy protein isolate, as shown in Figure 4. When assembled into a supercapacitor, a high specific capacitance of 219 F/g was recorded at 0.2 A/g with capacitance retention of 98.9% after 50,000 cycles at 20 A/g. High-performance supercapacitors can be made using electrospun carbon nanofibers, which has been demonstrated to have considerable potential. Their capacitive performance can be greatly enhanced by increasing the surface area, pore volume, surface wettability, and conductivity of carbon nanofibers. It is clear that the hierarchical porous High-performance supercapacitors can be made using electrospun carbon nanofibers, which has been demonstrated to have considerable potential. Their capacitive performance can be greatly enhanced by increasing the surface area, pore volume, surface wettability, and conductivity of carbon nanofibers. It is clear that the hierarchical porous structure with connected pores will offer substantial active surface areas, rapid ion diffusion, and highperformance electrodes. The rate performance and long-term cycling stability are increased when high conductivity materials, such as graphene and carbon nanotubes, are added into electrospun nanofibers.
Carbon nanofibers can be given a pseudocapacitive property to increase their capacitance, rate capacities, and cycling stability. Examples of this include combining them with heteroatoms, conducting polymers, and transition metal compounds. Despite decades of study on carbon nanofiber electrodes, most carbon nanofiber materials are still in the research and development stage because of their poor production rates and expensive fabrication processes. By using needleless electrospinning processes, precursor nanofiber production will be scaled up, hastening their commercialization. Additionally, using natural resources to create precursor nanofibers could lower the cost of production. The energy storage capacity and capacitor performances will be improved by optimizing the carbonization process, adding a hierarchical porous structure to carbon nanofibers, and boosting electrical conductivity.

Hydrothermal Carbonization
Hydrothermal carbonization (HTC) is a promising thermo-chemical approach for converting carbon precursors to functional porous materials in a confined environment at low temperature (180-260 • C) and pressure in an aqueous acidic or neutral solution [21]. The aqueous solution, residence time, applied pressure, and temperature all significantly impact the structure-property of the generated biochar. Typically, an activation step is required to enrich the pore structure further and increase the degree of graphitization of biochar. Using this approach, chitosan-derived carbon was generated through hydrothermal carbonization at 200 • C for 2 h and activated with acetic acid. The surface area of the resulting porous carbon was 3532 m 2 /g [21]. Furthermore, Lin et al. [31] discovered that B/N dual-doped porous carbon can be produced using boric acid. The synthesized porous carbon had improved capacitance and electrode stability. The activation procedure began with a 1:2 combination of carbon and boric acid, which was then placed in a Teflon-lined autoclave. For 5 h, the autoclave ran continuously at 160 • C. A capacitance of 316 F/g was recorded. Ren et al. used a one-step hydrothermal approach to produce oxygen-doped activated carbon-graphene composite hydrogels, as shown in Figure 5. In the hybrid hydrogel, high specific surface area-activated carbon derived from chitosan and oxygen-containing groups introduced via a simple room-temperature oxidation strategy with HNO 3 are assembled into the framework of reduced graphene oxide (rGO) to effectively prevent the restacking of rGO nanosheets and result in high specific surface area and high conductivity of the composite hydrogels, resulting in an excellent energy storage performance. At a current density of 1 A/g, the optimized sample had a high specific capacitance of 376 F/g in 1 M H 2 SO 4 electrolyte. Furthermore, after 5000 charge-discharge cycles at 10 A/g, the assembled flexible supercapacitor demonstrated optimal cycling stability of 83%.
HTC has been widely reported as one of the most effective methods of producing carbon materials with tunable chemical and physical properties. The HTC carbon structure can be significantly improved (the surface area and pore volume) by combining the HTC with other methods such as templating. Additionally, chemical and physical activation increases specific surface area and creates porosity. Table 1 compares a few samples of HTC-prepared materials to other methods of preparation, as well as their primary porosity properties (surface area) and electrochemical performance.
taining groups introduced via a simple room-temperature oxidation strategy with HNO3 are assembled into the framework of reduced graphene oxide (rGO) to effectively prevent the restacking of rGO nanosheets and result in high specific surface area and high conductivity of the composite hydrogels, resulting in an excellent energy storage performance. At a current density of 1 A/g, the optimized sample had a high specific capacitance of 376 F/g in 1 M H2SO4 electrolyte. Furthermore, after 5000 charge-discharge cycles at 10 A/g , the assembled flexible supercapacitor demonstrated optimal cycling stability of 83%. HTC has been widely reported as one of the most effective methods of producing carbon materials with tunable chemical and physical properties. The HTC carbon structure can be significantly improved (the surface area and pore volume) by combining the HTC with other methods such as templating. Additionally, chemical and physical

Microwave-Assisted Activation
Microwave-assisted carbonization technique is an energy-efficient process and can be considered as an alternative to traditional hydrothermal procedures, having the advantages of a short retention period, and homogenous heating. Recently, Jeyabanu et al. [11] used microwave irradiation to create lanthanum nanospheres doped in CuS (La@CuS) at various compositions (La = 0, 1, 3, and 5%). The reduction and oxidation peaks were found at 0.064 V and 0.64 V, respectively, and 100 mV/s scan rate. High specific capacitance of 1329 F/g was obtained for the La = 5% sample at 2 mA current density, while pure CuS with no La doping had a specific capacitance of 1040 F/g at the same current density. The remarkable performance of the La = 5% sample can be due to the addition of pseudocapacitance, which resulted in strong ionic transfer with low internal resistance when compared to the other samples. Li et al. [33] also created nitrogen-doped hierarchical porous carbons with chitosan hydrogels as a precursor and ZnCl 2 as an activator. The microwave activation of the samples took only 10 min, making it faster and more energy-efficient than conventional approaches. The synthesized N-doped porous material demonstrated a high specific capacitance of 435 F/g at 0.2 A/g in 6 M KOH in a three-electrode setup and outstanding capacitance retention of 71.0% at a high current density of 10 A/g. Furthermore, the designed symmetric supercapacitor exhibits a power density of 50 W/kg, a maximum energy density of 9.4 Wh/kg, and no discernible capacitance loss after 10,000 cycles.
The microwave-assisted activation process can be considered in order to help increase the yield of carbonaceous materials and improve the hierarchical porous structure with less formation and emission of hazardous material. Carbonaceous materials derived from biopolymeric materials via microwave-assisted activation possess excellent properties, such as high SSA, high porosity, and tailored hierarchical superstructure, thus improving the capacitance performance of carbon-based supercapacitors. Thus, the complicated and time-consuming chemical activation followed by the carbonization processes can be simplified into a one-step microwave-assisted activation approach to preparing hierarchically porous carbon.

Template Method
Template strategies (hard template, soft template, and dual-template) are efficient for preparing porous materials with controlled pore size distribution and moderate morphologies [34,35]. For instance, B and N were doped in carbon nanosheets via a simple dual-template method ( Figure 6) using methyl cellulose as a carbon precursor. The resulting carbon electrode displayed a high capacitance of 572 F/g at 0.5 A/g and retained 281 F/g at 50 A/g in an acidic electrolyte, due to the synergistic effects of the large surface area with the hierarchical porous structure, B/N co-doping, and a high degree of graphitization. In addition, after 20,000 cycles in the "water in salt" electrolyte, the symmetric device built with bacterial cellulose-based gel polymer electrolyte delivered a high energy density of 43 Wh/kg and exceptional stability of 97.8% [36]. In another work, Song and coworkers [37] also used soft templates (nano-sized MgO and Pluronic F127) to produce hierarchical porous carbon from lignin. Pluronic F127 acts as a dispersant, inhibiting MgO agglomeration, while MgO nanoparticles act as substrates and the principal template through a space-occupying action. Figure 7 depicts the synthesis process, which resulted in an active surface area of 712 m 2 /g and a pore volume of 0.90 cm 3 /g. The resulting carbons' electrochemical performance as a supercapacitor electrode material was examined. Even though the vacuum environment improved porosity and pore homogeneity, the corresponding carbon did not display superior electrochemical performance to carbon obtained without a vacuum environment. In another work, Song and coworkers [37] also used soft templates (nano-sized MgO and Pluronic F127) to produce hierarchical porous carbon from lignin. Pluronic F127 acts as a dispersant, inhibiting MgO agglomeration, while MgO nanoparticles act as substrates and the principal template through a space-occupying action. Figure 7 depicts the synthesis process, which resulted in an active surface area of 712 m 2 /g and a pore volume of 0.90 cm 3 /g. The resulting carbons' electrochemical performance as a supercapacitor electrode material was examined. Even though the vacuum environment improved porosity and pore homogeneity, the corresponding carbon did not display superior electrochemical performance to carbon obtained without a vacuum environment.
The template method makes it simple to prepare carbon materials with uniform and tunable pores. The production of the template, however, is an expensive, laborious, and time-consuming process. Another difficulty is being able manage the thickness of the pores, which is essential for regulating the pore diameters of freshly generated carbon materials. In addition, the need for acid or alkali etching to remove inorganic templates limits their usefulness. There are more options to synthesize biopolymeric materials and other carbon sources that cannot be synthesized using other conventional techniques thanks to special templates such as zinc. However, the interplay between the carbon precursor and the templates needs to be thoroughly investigated utilizing various novel templates. The template method makes it simple to prepare carbon materials with uniform and tunable pores. The production of the template, however, is an expensive, laborious, and time-consuming process. Another difficulty is being able manage the thickness of the pores, which is essential for regulating the pore diameters of freshly generated carbon materials. In addition, the need for acid or alkali etching to remove inorganic templates limits their usefulness. There are more options to synthesize biopolymeric materials and other carbon sources that cannot be synthesized using other conventional techniques thanks to special templates such as zinc. However, the interplay between the carbon precursor and the templates needs to be thoroughly investigated utilizing various novel templates.

Keratin-Derived Materials
Keratin is a unique bio-derived polymer with multifunctional features that makes it ideal for use as active material in electrochemical energy storage applications, particularly supercapacitors. Many recent investigations have used keratin in the production of novel green sustainable electrode materials for supercapacitors [43,[51][52][53][54]. Despite much new knowledge about the role of keratin in energy storage applications, some researchers [43,55] have also exploited human hair as a keratin source for a similar application. Human hair as a biopolymer has been used in recent times as flexible electrode material for supercapacitors. The rise in wearable energy storage devices has increased the demand for flexible electrode materials to be synthesized for such applications [54]. Human hair possesses properties such as high elasticity, controllable length, and low cost.
Carbon material can be derived from the keratin in human hair using the microwaveassisted method. An efficient and risk-free microwave-assisted approach was reported by Liu et al. [54] for developing super elastic reduced graphene oxide encapsulating human hair (rGO@Hh) to generate a conductive and high-strength fibrous electrode. The human hair/Ni/rGO/MnO 2 fiber was created by, first, uniformly coating the human hair with a thin Ni layer via e-beam deposition. Second, after many hours of immersion in GO solution, GO spontaneously assembles on the human hair/Ni fiber. Chemical bath deposition is then used to create honeycomb-structured MnO 2 on human hair/Ni/rGO fiber. Finally, allsolid-state flexible FSCs are created by carefully twisting the human hair/Ni/rGO/MnO 2 fiber electrode wrapped in a layer of gel electrolyte and the human hair/Ni/rGO fiber electrode together. The resulting fibers are one-dimensionally coaxial, facilitating electron transport over particle electrode materials. The interwoven rGO@Hh fibers showed an interconnected porous structure with a high specific capacitance of 316 F/g at 1 A/g and strong cycle behavior. Furthermore, rGO@Hh and Ni (OH) 2 /rGO@Hh fibers were used as negative and positive electrodes in a solid-state fiber-based asymmetric supercapacitor (FASC), which showed high energy of 27.6 Wh/kg and a power density of 699 W/kg, respectively. In addition, Zhang et al. [56] reported on simultaneous ZnCl 2 activation and FeCl 3 graphitization at varied heating temperatures. This yielded graphitic nitrogen-doped hierarchical porous carbon nanosheets and was employed for supercapacitor application from a readily produced green silk, as shown in Figure 8e. The degree of graphitization and BET surface area increased to their greatest values when the heating temperature was increased from 700 • C to 850 • C, while the nitrogen doping concentration was kept at 2.24 wt%. A porous nanosheet structure offers minimum diffusive resistance and shortens the diffusion pathways. Results from the HR-TEM confirmed the formation of worm-like stripes, indicating the presence of partial graphitization, and many crystal stripes, hinting at high graphitization during the carbonization process.

Alginate-Derived Materials
Alginate is a polyanionic bio-polymer, widely used in various applications for manufacturing energy storage materials from abundant and non-toxic marine biomass resources, such as sodium alginate, potassium alginate, etc. [57]. Recent studies [57][58][59][60][61][62] have indicated that alginate biopolymer-derived biomass carbon materials, in addition to being green, low cost, and renewable, also possess electrochemical properties which make them suitable for supercapacitor applications [63]. Through carbonization of renewable natural alginate, Wang et al. [64] demonstrated a sustainable biomass conversion technique and non-templated strategy for fabricating the macro-, meso-, and microporous carbon aerogel (CA) produced using the sol-gel method. The alginate hydrogel's gelation process Carbonized silk with a nanosheet morphology and a large specific surface area (1285.31 m 2 /g) was constructed into a supercapacitor as an electrode material and showed outstanding electrochemical performance with a high specific capacitance of 178 F/g at 0.5 A/g, as shown in Figure 8a-d, and an excellent rate capability, as well as 81% capacitance retention ratio, even at 20 A/g. In an aqueous neutral Na 2 SO 4 electrolyte, a symmetric supercapacitor with carbonized silk electrodes at 850 • C has exceptional specific energy of 14.33 Wh/kg and a power density of 251 W/kg. Similarly, Sinha et al. [51] described a scalable process for making hierarchically porous, heteroatom-doped activated carbon nanosheets from waste biomass human hair and showed how this carbon might be used as an ultrahigh performance electrode material for supercapacitor applications. The carbon nanosheets (50 to 200 nm size) produced had a hierarchical porous structure with a specific surface area of 1548 m 2 /g. The presence of porous structure is further confirmed with nitrogen adsorption and desorption studies. The well-dispersed graphitic pockets induce the enhancement in conductivity of ions inside the sample and the presence of porosity provides sufficient sites for electrolytic ions to be penetrated. At a current density of 1 A/g, an exceptional specific capacitance value of 999 F/g was obtained. At a power density of 325 W/kg, a maximum energy density of 32 Wh/kg was achieved. Furthermore, at a high current density of 5 A/g, exceptional cyclic stability of 98% capacitance retention was obtained after 10,000 cycles.

Alginate-Derived Materials
Alginate is a polyanionic bio-polymer, widely used in various applications for manufacturing energy storage materials from abundant and non-toxic marine biomass resources, such as sodium alginate, potassium alginate, etc. [57]. Recent studies [57][58][59][60][61][62] have indicated that alginate biopolymer-derived biomass carbon materials, in addition to being green, low cost, and renewable, also possess electrochemical properties which make them suitable for supercapacitor applications [63]. Through carbonization of renewable natural alginate, Wang et al. [64] demonstrated a sustainable biomass conversion technique and non-templated strategy for fabricating the macro-, meso-, and microporous carbon aerogel (CA) produced using the sol-gel method. The alginate hydrogel's gelation process shown in Figure 9e might provide a novel way to make macro-and mesoporous structures. The produced carbon material had a 3D self-supporting core macroporous network with a core diameter of around 2-5 m and thin walls of less than 100 nm, which can operate as electrolyte reservoirs, according to SEM analysis. The presence of many macropores and thin walls was confirmed by the TEM studies. The macropores are approximately 200-300 nm in size (diameter). The high-resolution TEM (HRTEM) image also reveals numerous micropores in the sample as well as an amorphous carbon structure with semi-graphitic domains. The macropores reduce the ion-transport barrier by shortening the electrolyte ion diffusion distance to the active sites. The as-prepared porous CA displays outstanding electrochemical performance, as shown in Figure 9a-d. Moreover, Li et al. [65,66] reported on combining sodium alginate (SA) and dopamine functionalized polypyrrole (DAPPy) nanofibers with borax as a cross-linking agent, yielding a series of multifunctional conductive hydrogels, which was dubbed SA-B-DAPPy. The conductivity of the hydrogel may be increased to 1.33 ± 0.012 S/m by increasing the DAPPy weight ratio to 3.5 wt.%. The adequate stretchability (more than 800%) and immediate self-healing ability of hydrogel frameworks can be attributed to both borate interactions and hydrogen bonds inside the frameworks. The doping process resulted in the formation of a sponge-like structure with rough pore walls. The synergistic effect of the dynamic borate, hydrogen bond cross-linking, and polymer chain entanglements endows the obtained hydrogel with high stretchability (elongation at break greater than 800%), fast self-healing ability (efficient instantaneous electrical and mechanical self-healing within 15 s), and arbitrarily moldable ability.
Similarly, Wei et al. [60] reported on the fabrication of oxygenated N-doped porous carbon as a key step in improving the performance of carbon materials and expanding their applications. Because most methods for the preparation of alginate-derived porous carbon require chemical activation agents and acid washing, synthesizing oxygenated N-doped porous carbon from alginate salts via a simple and low-cost method remains a major challenge. Through carbonization of ammonium alginate aerogel followed by air activation treatment, oxygenated N doped porous carbon with a high surface area was effectively synthesized by Wei et al. [60]. Only the greenest water is used as a solvent in the production of porous carbon, and its volume has a major impact on the porous structure of the carbonization result, which may be further adjusted by air activation treat-ment. The porous carbon produced from alginate has an interconnected three-dimensional porous network structure. The formation of an interconnected three-dimensional porous network structure is caused by ice sublimation and alginate flexibility. Following air activation, ordered graphene domains with substantially richer porosity architectures can be detected. This finding unequivocally supports the effect of air activation on the porous structure of carbon materials. Due to its rich porous structures and heteroatom doping, the obtained porous carbon exhibits excellent electrochemical performance when used as electrode materials for supercapacitors, such as high specific capacitance (204 F/g at 1 A/g in a two-electrode system), good rate capability, and ultralong cycle life (91.2% capacitance retention after 10,000 charge/discharge cycles). This research might be extended to benefit additional uses of alginate-derived carbon and could pave the way for a novel method of fabricating heteroatom doped porous carbon. Similarly, Wei et al. [60] reported on the fabrication of oxygenated N-doped porous carbon as a key step in improving the performance of carbon materials and expanding their applications. Because most methods for the preparation of alginate-derived porous

Pectin-Derived Materials
Pectin is a complex group of heteropolysaccharides that make up a significant portion of dicotyledonous plants' basic cell walls and perform vital functions in their growth and development. Pectin has been extensively researched in a variety of fields, such as electrochemical energy storage [40], food [63], agriculture [64], and medicine [65], due to its excellent properties.
Recent studies [41,[66][67][68] have shown that pectin biopolymers can be used as an electrode [41,68] and electrolyte [66,67] materials in supercapacitors. Perumal and Selvin [66], for the first time, utilized Li + conducting pectin electrolytes in a solid-state EDLC, manufactured using a solution casting. For additives at a ratio of 30 (m. wt.%) pectin and 70 (m. wt.%) LiBr, the produced pectin electrolytes exhibited a considerable conductivity of 3.44 × 10 −3 S/cm. This ideal Pectin/LiBr composite material was suggested for the manufacture of solid-state EDLC, as it exhibits an electrochemical capacitance of 19.04 F/g and outstanding reversible performance, as shown in Figure 10. Based on these promising discoveries, research on bio-macromolecular electrolytes offers an advanced foundation for creating resilient energy storage devices, particularly wearable and flexible ones. The effects of electron-withdrawing-donating groups on the capacitive behavior of p-hydroquinone (PHQ) can be used to improve supercapacitors. The electron-withdrawing group (EWG) and electron-donating group (EDG), in a study by Jie and Ying [69], are sulfonic acids and methoxyl groups, which are the substances of 2,5-dihydroxybenzenesulfonate (DHBS) and 2 methoxy hydroquinone (MHQ), respectively. These substances were derived from pectin and used to improve redox reaction in supercapacitor electrolytes. The use of PHQ, DHBS, and MHQ as redox additives in H2SO4 electrolyte was demonstrated and two-proton-two-electron redox reactions occur at the electrode-electrolyte interface. When subjected to PHQ, DHBS delivered a larger faradaic impact than MHQ, showing that the EWG is more active than the EDG. Furthermore, all the important redox reactions are kinetically constrained by semi-infinite diffusion. When measured in The effects of electron-withdrawing-donating groups on the capacitive behavior of p-hydroquinone (PHQ) can be used to improve supercapacitors. The electron-withdrawing group (EWG) and electron-donating group (EDG), in a study by Jie and Ying [69], are sulfonic acids and methoxyl groups, which are the substances of 2,5-dihydroxybenzenesulfonate (DHBS) and 2 methoxy hydroquinone (MHQ), respectively. These substances were derived from pectin and used to improve redox reaction in supercapacitor electrolytes. The use of PHQ, DHBS, and MHQ as redox additives in H 2 SO 4 electrolyte was demonstrated and two-proton-two-electron redox reactions occur at the electrode-electrolyte interface. When subjected to PHQ, DHBS delivered a larger faradaic impact than MHQ, showing that the EWG is more active than the EDG. Furthermore, all the important redox reactions are kinetically constrained by semi-infinite diffusion. When measured in 1 mol/L H 2 SO 4 , a high energy density of 15.6 Wh/kg was achieved for the DHBS sample with a concentration of 2 mmol/L. Other supercapacitor systems with electron-withdrawing-donating groups would benefit from this current research.

Gelatin-Derived Materials
Gelatin is an alternative biopolymer that is frequently used in the development of supercapacitors' electrodes, due to its unique biological, gelling, interfacial, and viscoelastic characteristics, and is also used in the energy storage and conversion sectors [1,24,70]. Based on these characteristics, Sun et al. [9] prepared a nanocomposite electrode synthesized by embedding tungsten disulfide (WS 2 ) nanoparticles in gelatin-derived hierarchical porous carbon. Honeycomb-like porous nanostructures were formed after washing out the salt. A number of WS 2 nanoparticles were dispersed and anchored on the carbon sheet. The shapes of these particles were irregular, and the sizes ranged from~20 nm to~100 nm. Due to its structural advantages, the generated nanocomposite electrode displayed significantly improved electrochemical characteristics. It had a high capacitance value of 1305.5 F/g as an electrode material at a current density of 0.2 A/g. Even after 3000 cycles at 10 A/g, the nanocomposite maintained a high capacitance of 482.6 F/g and preserved 94% of its original capacitance. Activated carbon was used as the anode and WS 2 nanocomposite as the cathode in the construction of an asymmetric capacitor. At 0.1 A/g, a capacitance of 135.9 F/g, an energy density of 27.2 Wh/kg, and a power density of 59.9 W/kg was attained. Furthermore, gelatin/starch/TiO 2 nanocomposite, which was synthesized by hydrolysis and microwave activation, showed good supercapacitive performance at a negative voltage window. A well dispersed TiO 2 NPs dispersed within the crystalline starch nanoparticles and oval shaped nano-gelatin NPs was formed. The nano-starch biopolymer serves as a compatible agent due to the similar bond structure it has with gelatin, and it will also help to optimize its low retention capacity. The TiO 2 does not support dendrite growths, so it alleviates volumetric variations, thereby reducing any form of nucleation overpotential during charging. At 5 mV/s, the three-electrode configuration achieved a high specific capacitance of 808 F/g, as well as an energy density of 208.3 Wh/Kg, and capacitance retention of 95% after 5000 cycles. The fabricated supercapacitor has a capacitance of 617 F/g and capacitance retention of 92% after 5000 cycles [71]. The utilization of nano level gelatin and starch for the fabrication of supercapacitor electrodes with superior electrochemical performance at negative volt-ages for possible applications in signal control systems and smart switches, as well as devices for future 4IR applications, is what makes this work unique. It serves as a foundation for the development of symmetrical supercapacitors that can readily switch polarities in places that require both positive and negative voltages. This innovative nano-form of gelatin and starch biopolymers outperforms their bulk counterparts in terms of adjustable transport characteristics and distinctive surface chemistry.

Lignin-Derived Materials
Lignin is a plentiful and easily accessible biomass regarded as a one-of-a-kind sustainable organic carbon source [72]. Lignin is a macromolecule with an exceedingly complicated three-dimensional reticulated molecular structure [6,73], containing 40-60% carbon, and is an excellent precursor for porous carbon [70]. Many features distinguish lignin-based porous carbon materials, including large active surface area, superior electrical conductivity, an interconnected pore structure, and high porosity. Porous carbon compounds based on lignin have several uses in supercapacitor applications [74,75]. Schlee et al. [76] spun the lignin fiber using kraft lignin. Thermal stabilization, carbonization, and CO 2 activation were used to create lignin fiber with a self-supporting microporous structure. Because of the extraction, it was feasible to electrospun fibers from pure lignin without the use of any additional synthetic high molecular weight polymer, such as PVA. The resulting fiber mats are made up of randomly intertwined cylindrical fibers. The average diameter of the as-spun fibers is 769 nm, which is rather large when compared to prior studies demonstrating that intermolecular interactions must occur [33,66]. Furthermore, the high polymer concentration in the solution (50 wt%), combined with the lack of additives (salts or co-polymers), results in fibers with large diameters [75]. The non-activated fiber is dense, whereas the CO2-activated fiber has more porosity and hence seems less dense. As a result, when evaluated in 6 M KOH electrolyte, the CO2-activated fiber mats demonstrated a high specific gravimetric capacitance of 155 F/g at 0.1 A/g, great rate capability of 113 F/g at 250 A/g, and good capacitance retention of 94% after 6000 cycles. As a result, it is possible to conclude that lignin is a suitable precursor for the production of microporous, oxygen functionalized carbon fibers for use as free-standing electrodes in aqueous supercapacitors.
Although some researchers have indicated that employing lignin as a single spinning solution through electrospinning and carbonization can effectively create nanofibers, in most situations, pure lignin electrospinning produces spray rather than fibers. As a result, additional high molecular weight polymers with strong spinnability properties, such as PAN, PEO, PVA, and PVP, must be added to the spinning solution during the electrospinning process [75]. In that regard, Butnoi et. al. [28] used a one-step electrospinning process to create a flexible nanofiber composite comprising lignin and nanofibers containing iron oxide nanoparticles, as shown in Figure 11a. Because of visible porosity and lumps, the surface of the doped nanofibers was rougher. This might be due to iron agglomeration and phase separations between the polymer and the iron precursor. The as-synthesized materials have well-retained carbon nanofibers in three-dimensional networks of nonwoven mats with randomly oriented nanofibers. The 10 wt% iron doped fibers had a higher average fiber diameter of 625 ± 133 nm. At a current density of 0.1 A/g, the nanofiber-Fe 3 O 4 electrode had a specific capacitance of 216 F/g and retained 97% of its capacitance after 1000 cycles at 1 A/g (Figure 11b). It should be emphasized that nanofibers generated by electrospinning from lignin have a high aspect ratio, a high specific surface area, high electrical conductivity, and good mechanical properties, making them a potential candidate material in the field of energy storage. From the research conducted by [77] and [28], the use of metal salt additions improves the pore structure and overall performance of the material.
A completely different approach based on spray drying and carbonization was employed by Cao [47] to prepare hollow carbon spheres. Kraft lignin was used as a carbon precursor, while potassium hydroxide (KOH) was used as an activator. The porous carbon particles produced have a surface area of 2425 m 2 /g and a mixture of hollow and spherical morphologies. The diffraction peaks from the (0 0 2) planes of graphitic carbon and (1 0 0) planes of the graphite lattice confirmed the formation of amorphous porous structures that are partially graphitized due to the simple carbonization process. When employed as a supercapacitor electrode, 31.8 F/g at 0.2 A/g was measured, which is greater than the 29.2 F/g produced from commercial activated carbon Kuraray YP-50F.
Fe3O4 electrode had a specific capacitance of 216 F/g and retained 97% of its capacitance after 1000 cycles at 1 A/g (Figure 11b). It should be emphasized that nanofibers generated by electrospinning from lignin have a high aspect ratio, a high specific surface area, high electrical conductivity, and good mechanical properties, making them a potential candidate material in the field of energy storage. From the research conducted by [77] and [28], the use of metal salt additions improves the pore structure and overall performance of the material.

Cellulose-Derived Materials
Cellulose is a popular biopolymer utilized in supercapacitor applications, derived from either plants or microorganisms [13]. Bacterial cellulose precursors have various benefits over classical precursors, including a more porous structure, a bigger surface area, superior biodegradability, large-scale cellulose production, and a high concentration of hydroxyl groups [6]. Due to its robust interaction with various added chemicals and the finely thinner morphology of bacterial cellulose compared to plant cellulose, these advantages transform bacterial cellulose into a tunable flexible scaffold appealing biomaterial that attracts widespread interest in forming a highly versatile three-dimensional carbon nanomaterial [78,79].
Hao et al. [80] employed bacterial cellulose to produce a hierarchical 3D porous carbon nanofiber network. When used as a binder-free electrode, the carbon nanofibers had a high surface area of 624 m 2 /g and good electrochemical performance. The TEM results also indicated a linked 3D porous network architecture made up of 20-50 nm nanofiber networks and developed porosity. Notably, such short nanofibers might give a high surface-to-volume ratio to boost SSA for charge accommodation during the charge-discharge process, while the unique interconnected porous network architecture will promote quick electron transfer/ion diffusion along 3D directions. According to high-resolution TEM (HRTEM), the nano-fibers are mostly formed of aligned graphitic layers (002) with a lattice distance of 0.34 nm and turbostratic carbon. The graphitic structure promotes ion-electron movement. In a three-electrode system with 0.5 A/g current density in 6 M KOH electrolyte, the as-prepared electrode had a maximum specific capacitance of 302 F/g. The symmetric supercapacitor created has a specific capacitance of 184 F/g at 0.25 A/g in aqueous electrolyte and remarkable capacitance retention of 98% after 5000 cycles. Mo et al. [81] also used sheet cellulose to create graphene-like porous carbon with a hierarchical pore structure. At 1 A/g in 6 M KOH aqueous electrolyte, a high specific surface area of 2045 m 2 /g was produced, resulting in gravimetric capacitance of 353 F/g and volumetric capacitance of 309.7 F/cm 3 . In an ionic liquid electrolyte in acetonitrile, the symmetric supercapacitor had gravimetric and volumetric specific energy densities of 120.1 Wh/kg and 80.4 Wh/L, respectively. In addition, Luo et al. [82] also created N-doped hierarchically porous nanocarbons from microcrystalline cellulose and tandem thermal treatment in CO 2 , N 2 , and NH 3 . It was possible to produce a carbon sponge with hierarchical pores and bi-modal (micro-and meso-porous) architectures. The stacked slice layers on the carbon surface made the carbon blocks appear fluffier, aggregating into 3D porous channels and voids. The porous cross-linked network is seen in the amorphous and extremely disordered carbon structures of the carbon material, which is filled with homogeneously scattered micro-mesopores. The pore volume of the optimized pyrolytic carbon was 1.6291 cm 3 /g, and the specific surface area was up to 3278 m 2 /g. According to electrochemical testing, the synthesized carbon delivered a specific capacitance of 234 F/g at 0.5 A/g and stayed at 201 F/g at 5 A/g, suggesting a strong storage capacity for supercapacitor applications.

Starch-Derived Materials
Polysaccharides and other similar biopolymers such as starch can be used as green electrodes in supercapacitor applications rather than just as binders and electrolytes, according to many recent studies [83]. A starch-derived porous carbon, as green electrode material for a supercapacitor, was reported by Pang et al. [84]. The XRD patterns indicated an increasing regularity of crystal structure resulting in better layer alignment. The morphology also indicated an irregular blocky shape structure with rough outer surface, and the particles were around 1-5 µm in size. The material displayed a specific capacitance of 144 F/g at a current density of 0.625 A/g in 6 mol/L KOH electrolyte and an energy density of 19.9 Wh/kg at a power density of 311 W/kg. Furthermore, Li et al. [85] used two-step carbonization and KOH chemical activation technique to create yam waste-derived 3D hierarchical porous carbon, as shown in Figure 12. The optimized sample has an ultra-high specific surface area of 2382 m 2 /g, a pore volume of 1.11 cm 3 /g, and simultaneous O-N co-doping. The resulting porous carbon has a pseudo-honeycomb-like 3D net structure with a pore diameter of about 50 µm and a thickness of 1-10 µm. When the prepared sample is employed as an electrode material for a supercapacitor, its structure promotes effective ion diffusion. Because of these unique characteristics, the optimized material has a high gravimetric capacitance of 423.23 F/g at 0.5 A/g, an impressive rate capability at 10 A/g, and outstanding cycling durability, with 96.4% capacity retention at a high current density of 10 A/g after cycles in 6 M KOH in a three-electrode system. Furthermore, the built symmetrical supercapacitor delivers a huge capacitance of 387.3 F/g at 0.5 A/g in 6 M KOH electrolyte. In 1 M Na 2 SO 4 electrolyte, it likewise exhibits high specific energy of 34.6 Wh/kg when the specific power is 200.1 W/kg, and commendable specific energy of 8.3 Wh/kg when the specific power is 4000 W/kg, as shown in Figure 13. As a result, this research can be used to develop high-performance electrode materials for supercapacitors.
N co-doping. The resulting porous carbon has a pseudo-honeycomb-like 3D net structure with a pore diameter of about 50 μm and a thickness of 1-10 μm. When the prepared sample is employed as an electrode material for a supercapacitor, its structure promotes effective ion diffusion. Because of these unique characteristics, the optimized material has a high gravimetric capacitance of 423.23 F/g at 0.5 A/g, an impressive rate capability at 10 A/g, and outstanding cycling durability, with 96.4% capacity retention at a high current density of 10 A/g after cycles in 6 M KOH in a three-electrode system.    Unlike Ruibin et al. and Pang et al., the following researchers focused on the use of different synthesis methods to produce their starch-based carbon materials and recorded different electrochemical properties. Chen et al. [86] utilized a two-step procedure for the fabrication of ultrathin carbon nanosheet-supported Ni quantum dot hybrids (C-Ni-QDs). TEM was used to examine the morphologies of C-Ni-QDs hybrids. The sample has a large number of Ni QDs that are equally distributed on the surface of a carbon nanosheet. The carbon nanosheets are transparent when exposed to electron beams, indicating their ultrathin nature. Furthermore, HR-TEM demonstrates that Ni QDs are approximately 5-10 nm in size with low agglomeration, which can give additional surface-active sites. The hybrid materials produced had a high specific capacitance of 1120 F/g at 2 A/g and outstanding rate capability with 81.3% retention ratio at 20 A/g. In addition, the C-Ni-QDs hybrids showed excellent cycling stability, with 97% capacitance retention after 2000 cycles. Additionally, Saliu et al. [87] reported on an as-prepared A-TiO 2 and U-TiO 2 which were achieved through the synthesis of TiO 2 on an activated and un-activated starch template, respectively, whiles the synthesis of TiO 2 without a template is unsupported-TiO 2 . The utmost result was A-TiO 2 , which has 72% anatase and 28% rutile and has a specific capacitance of 388 F/g, an energy density of 194 Wh/kg, a power density of 4473 W/kg, and 99% retention capacity after 20,000 cycles.

Chitosan-Derived Materials
Chitosan is the subject of extensive study and development because it is seen as a material with enormous potential for structural alterations to impart desired qualities and functionalities in the future. Recently, Wei et al. [88] reported having successfully formed a sandwich-like structure (CPCM/MXene) by incorporating Ti 3 C 2 T x MXene into chitosanbased porous carbon microsphere (CPCM) through electrostatic contact. Because porous carbon microspheres generated from chitosan have a 3D honeycomb structure, incorporating Ti3C2Tx into carbon microspheres has no effect on this structure. Furthermore, Ti3C2Tx nanosheets bind to the surface of the porous carbon microspheres, thereby preventing stacking and forming a sandwich-like structure. Lv et al. [89] and Xiao et al. [90] effectively synthesized nitrogen and sulfur co-doped porous chitosan hydrogel-derived carbons (CHC-SK) and N, P-co-doped porous carbon materials (NPPCs), using one-step carbonization technique and new phytic acid-induced self-assembled chitosan aerogel synthesis, followed by pyrolysis/activation respectively.
In another work, Ba et al. [91] concentrated on nitrogen-doped hierarchical porous carbon (NHPC) materials that were manufactured employing a chitosan-polyethylene glycol (PEG) blend as the raw material and a simple carbonization-activation procedure, as shown in Figure 14. Chitosan was used as a nitrogen-containing carbon precursor, and low-cost, large-scale commercial PEG was used as a porogen in this approach. The ratio of chitosan and PEG had an impact on the physical and electrochemical properties of the NHPC that resulted. The sample obtained by the 3:2 ratio had a large specific surface area (2269 m 2 /g), mild nitrogen doping (3.22%), and a well-structured pore structure. NHPC exhibits an amorphous structure, and some locally ordered structure could be observed, indicating partial graphitization of the synthesized materials. At a current density of 1 A/g, it showed a high specific capacitance of 356 F/g in 1 M H 2 SO 4 and 271 F/g in 2 M KOH, and over 230 F/g was retained at a current density of 20 A/g in both electrolytes. of chitosan and PEG had an impact on the physical and electrochemical properties of the NHPC that resulted. The sample obtained by the 3:2 ratio had a large specific surface area (2269 m 2 /g), mild nitrogen doping (3.22%), and a well-structured pore structure. NHPC exhibits an amorphous structure, and some locally ordered structure could be observed, indicating partial graphitization of the synthesized materials. At a current density of 1 A/g, it showed a high specific capacitance of 356 F/g in 1 M H2SO4 and 271 F/g in 2 M KOH, and over 230 F/g was retained at a current density of 20 A/g in both electrolytes.  In addition, as shown in Figure 15, the built symmetric supercapacitors have outstanding cycling stability, with 94% (in 1 M H 2 SO 4 ) and 97% (in 2 M KOH) retention after 10,000 cycles at 1 A/g. These findings suggest that a chitosan-PEG blend can be used as a unique and suitable precursor for the preparation of low-cost NHPC materials for high-performance supercapacitors. Nayak et al. [92], unlike the other researchers, obtained Ag-Zirconia nanocomposite material using a green synthesis approach. The Ag-Zirconia nanocomposites outperformed the pure Zirconia in terms of specific capacitance, which is 256 F/g as against 193 F/g at a current density of 1 A/g. Furthermore, a supercapacitor device was constructed employing the synthesized nanocomposites and activated carbon, which had an enhanced energy density of 31.94 Wh/kg at a power density of 500.86 W/kg. The device's stability was also noted to be outstanding, with 89% retention capacity after 2500 cycles at 10 A/g.
Wang et al. [93] and Shang et al. [94] both described a new method for producing heteroatom-doped hierarchical porous carbon (HPC-700) and biobased N-doped hierarchically porous carbon (N-HPC) electrode from chitin/KMnO 4 activating agent and marine crustacean derivatives/chitin nanofibers (ChNF), respectively. As a consequence, the HPC-700 electrode had an ultrahigh specific capacitance of 412.5 F/g at 0.5 A/g, outstanding electrochemical stability (only 0.4% loss after 10,000 cycles), and a high energy density of 9.67 Wh/kg, whereas the findings of N-HPC electrodes revealed that N-HPC electrodes had a capacitive performance of 128.5 F/g at 0.2 A/g and a very good electrochemical stability even after 5000 cycles. Zheng et al. [95] made N-doped porous carbon nanospheres by direct pyrolysis of chitin nanogels, which were easily created by mechanical agitation caused by sol-gel transition of chitin solution in NaOH/urea solvent, as shown in Figure 16. The carbon nanospheres are assembled into an interconnected framework with partial graphitized structure and an adjacent interlayer distance of~0.3 nm. Wang et al. [93] and Shang et al. [94] both described a new method for producing heteroatom-doped hierarchical porous carbon (HPC-700) and biobased N-doped hierarchically porous carbon (N-HPC) electrode from chitin/KMnO4 activating agent and marine crustacean derivatives/chitin nanofibers (ChNF), respectively. As a consequence, the HPC-700 electrode had an ultrahigh specific capacitance of 412.5 F/g at 0.5 A/g, outstanding electrochemical stability (only 0.4% loss after 10,000 cycles), and a high energy density of 9.67 Wh/kg, whereas the findings of N-HPC electrodes revealed that N-HPC electrodes had a capacitive performance of 128.5 F/g at 0.2 A/g and a very good electrochemical stability even after 5000 cycles. Zheng et al. [95] made N-doped porous carbon nanospheres by direct pyrolysis of chitin nanogels, which were easily created by mechanical agitation caused by sol-gel transition of chitin solution in NaOH/urea solvent, as shown in Figure  16. The carbon nanospheres are assembled into an interconnected framework with partial graphitized structure and an adjacent interlayer distance of ~0.3 nm. The carbon nanospheres that emerged had structured micropores (centered at 0.6 nm) and a high BET surface area of up to 1363 m 2 /g, which was significantly higher than that of raw chitin carbons (600 m 2 /g). Furthermore, the carbon nanospheres had a nitrogen concentration of 3.2% and good conductivity. As a result, supercapacitor electrodes made from carbon nanospheres pyrolyzed at 800 °C demonstrated a specific capacitance of 192 F/g at 0.5 A/g current density and outstanding rate capability. As shown in Figure 17, Ndoped porous carbon nanospheres showed outstanding cycling stability in both aqueous and organic electrolytes, as well as an outstanding energy density of 5.1 Wh/kg at a power density of 2364.9 Wh/kg when assembled in a symmetrical two-electrode cell. This research presents a new and effective process for making N-doped porous carbon nanospheres directly from chitin, demonstrating the enormous potential of using abundant polymers found in nature for energy storage. The carbon nanospheres that emerged had structured micropores (centered at 0.6 nm) and a high BET surface area of up to 1363 m 2 /g, which was significantly higher than that of raw chitin carbons (600 m 2 /g). Furthermore, the carbon nanospheres had a nitrogen concentration of 3.2% and good conductivity. As a result, supercapacitor electrodes made from carbon nanospheres pyrolyzed at 800 • C demonstrated a specific capacitance of 192 F/g at 0.5 A/g current density and outstanding rate capability. As shown in Figure 17, N-doped porous carbon nanospheres showed outstanding cycling stability in both aqueous and organic electrolytes, as well as an outstanding energy density of 5.1 Wh/kg at a power density of 2364.9 Wh/kg when assembled in a symmetrical two-electrode cell. This research presents a new and effective process for making N-doped porous carbon nanospheres directly from chitin, demonstrating the enormous potential of using abundant polymers found in nature for energy storage.

Collagen-Derived Materials
Collagens are the most common family, with more than 20 distinct collagen types recognized currently [97][98][99][100]. Collagens are essential for the production of extracellular matrix fibrillar and microfibrillar networks, basement membranes, and other extracellular

Collagen-Derived Materials
Collagens are the most common family, with more than 20 distinct collagen types recognized currently [97][98][99][100]. Collagens are essential for the production of extracellular matrix fibrillar and microfibrillar networks, basement membranes, and other extracellular matrix structures [101,102]. The extracellular matrix nature of collagen gives it a larger surface area for super capacitive applications [103,104]. Lei et al. [105] reported on a feasible and simple approach for synthesizing Mn-doped N-containing carbon compounds using collagen waste for supercapacitor applications. The metal ions were chelated with bayberry-tanninimmobilized collagen fiber, followed by a carbonization procedure, to produce Mn-doped N-containing carbon. The highest specific capacitance value for the Mn/N-C-x material (where x is the carbonization temperature) was 272.62 F/g in 1 M KOH electrolyte solution with a highly obtained nitrogen content at a carbonization temperature of 800 • C. However, at a carbonization temperature of 1000 • C, the Mn/N-C-x material recorded the lowest specific capacitance value of 240.27 F/g resulting from the decrease in nitrogen content. The rate capability of the Mn/N-C-800 was 72.21% from 1 to 20 A/g, and it remained at 81.4% after 6000 cycles. In another work, Yu et al. [106] stated the use of sol-gel, freezedrying, carbonization, and KOH activation multistep processes to make nitrogen-doped carbon aerogels by employing sodium carboxymethyl cellulose (ferric trichloride and collagen), as a cross-linking agent, and nitrogen sources, respectively. Carbon aerogels with well-developed porous three-dimensional morphologies, large specific surface areas, and outstanding magnetic characteristics were discovered. The samples all have the characteristic crosslinked 3D network structure. Clearly, the amount of collagen introduced enhanced the lamellar thickness. This could be because the high collagen content slowed the cross-linking rate and lengthened the gel development stage, resulting in the creation of comparatively thick layers after the freeze-drying and carbonization processes. In a 6 M KOH electrolyte, the CA-N 0.5 demonstrated a specific capacitance of 185.3 F/g when used as an electrode material with a current density of 0.5 A/g. After 5000 charge-discharge cycles, the specific capacitance retention was 90.2%, showing outstanding cycling stability. To access the electrochemical performance of the various biopolymeric materials stated earlier, Table 2 lists the electrochemical performances of several biopolymeric materials.

Challenges of Biopolymer-Based Materials for Supercapacitor Applications
One aspect of technology that is becoming increasingly essential is choice of materials for fabrication of energy storage devices. Over the years, there has been major variations in the materials used for electrolyte and electrode. Recently, significant achievements in the key aspects of energy storage devices that includes electrode-electrolytes materials were unveiled. The achievements lie in the utilization of environmentally friendly, inexpensive, flexible, and lightweight electrode-electrolyte materials for energy storage. Several natural precursor materials have been explored for flexible wearable devices. Biopolymers are one of the natural materials used for electrode-electrolyte of the flexible wearable devices. Biopolymers are currently at the verge of becoming the most suited precursor material for electrode-electrolyte materials due to its excellent properties such as high flexibility, lightweight, and environmental friendliness.
Carbon-based materials are a family of the most promising and attractive electrode materials, and they offer many advantages that make them perfect for supercapacitor applications. They are earth-abundant, non-toxic, and inexpensive materials, yet have good operational performance. Despite the impressive properties exhibited by biopolymer derived electrode materials, there is still room for improvement on the microstructures in order to achieve higher energy and power densities. For instance, the size, structure, morphology, and surface properties of generated carbons may vary greatly depending on the developing environment and subsequent composition of natural biopolymer sources received from distinct regions. As a result, it is challenging to replicate the electrochemical characteristics of carbons. A price variance in the market may result from the widespread usage of commercially valuable biopolymers (such as keratin, chitosan, chitin, and starch) to manufacture carbon electrode materials, outweighing any potential economic benefits. Additionally, necessary pre-processing tasks, such as reducing biopolymers to fine powders and eliminating impurities, are time-consuming and difficult. Some fabrication techniques also call for harsh environmental conditions such as high temperatures and corrosive chemicals. Therefore, it is crucial for researchers to concentrate on low-cost techniques for isolating biopolymers, such as keratin, starch, gelatin, alginate, chitosan, and so forth, from their natural sources, enabling hassle-free advancement in the field of biopolymer-based electrode materials.
More importantly, biopolymer-based carbons typically have disordered pore morphologies and a wide range of pore sizes. The rate performance and power density are constrained by the difficulty of precisely tuning pore parameters such as shape, structure, and regularity. Furthermore, understanding the different interactions that the biopolymer contributes to (covalent bonding, hydrogen bonding, van der Waals interaction, etc.) is crucial since they improve the mechanical and electrical characteristics of the resulting biopolymer-based electroactive material.
In this regard, it is imperative to design high-performance biopolymer-based materials as an electrode and electrolyte for solid-state and flexible supercapacitor applications.

Conclusions and Future Outlook
The goal of this review was to provide an overview of the most current developments in the use of biopolymer-based materials for supercapacitor applications. Using sustainable and low-cost green biopolymers as raw precursors to make porous electrodes may assist to lessen dependency on nonrenewable resources while also delivering major benefits to the energy storage field. Some biopolymer-derived porous materials exhibit interconnected porous architecture, as well as heteroatom doping, physicochemical stability, and various nanostructures, resulting in improved performance rate, high capacitance, and cyclic stability. Furthermore, the formation of composite materials combining biopolymer-derived materials with conductive materials, such as graphene, transition metals, and conductive polymers, results in efficient charge transfer, rapid redox reaction kinetics, and durable structures, resulting in hybrids with a long-life cycle and high energy density. The synthesis methods and the obtained structure will inform the application of the various biopolymerbased materials for various applications, as highlighted in Figure 18. Although a great number of experts have put in a lot of effort to make biopolymer-based materials suitable for use in supercapacitors, there are still a few obstacles that will need to be overcome soon. (1) Scalable synthesis: green biopolymers come from a variety of sources; nevertheless, their production is complex, expensive, and challenging on a large scale, requiring the separation of certain components from the green biopolymeric resources and the incorporation of other electrochemically active materials. Because of the different sources of (1) Scalable synthesis: green biopolymers come from a variety of sources; nevertheless, their production is complex, expensive, and challenging on a large scale, requiring the separation of certain components from the green biopolymeric resources and the incorporation of other electrochemically active materials. Because of the different sources of biopolymers, the flexibility and mechanical strength of certain derived materials are insufficient for practical use. (2) Advanced characterization and evaluation of supercapacitor biopolymer-derived electrode materials are extremely promising as materials for various components.
In situ infrared spectroscopy, in situ TEM, AFM, in situ SEM, and in situ XRD should be used to further investigate their synthesis and interfacial reaction processes. Furthermore, by integrating further experiments with theoretical calculations, a deeper understanding of the electrochemical processes, structural and textural properties of the synthesized materials can be obtained. This would provide intriguing directions for future research. (3) Control of structure-properties-performance: Biopolymers, as a type of natural material, have unique properties that do not quite meet the size necessary for ionic mobility in supercapacitors, hence managing these naturally generated pores remains a difficulty. At the moment, chemical approaches for changing the pore size of biopolymers are effective. The electrochemical performance of the electrode made from the modified biopolymer has improved, but it still falls short of the requirements. Based on this, electrode materials with uniform pore size and specific surface area distribution may be generated using proper design and synthesis procedures, allowing high performance supercapacitors to be assembled. With the continuous research and exploration of green biopolymer-based materials, we surely believe that these renewable carbon resources will replace traditional petroleum-based products and obtain extensive applications in the energy storage field.