Fluorinated Polyurethanes, Synthesis and Properties

Fluorinated polyurethanes with a glass transition temperature as low as −139 °C and a decomposition onset temperature of 247–330 °C were prepared by a reaction of fluorinated alcohols with aromatic and cycloaliphatic diisocyanates in solution or melt.


Introduction
Reactions of aromatic and aliphatic diisocyanates are extensively employed in the synthesis of valuable polymeric materials, viz. polyurethanes (PUs). The preparation of polymers is often assisted by catalysts such as tertiary amines, organotin compounds, etc. [1]. Depending on the starting compounds, plastics or rubberlike products are afforded.
The fluorine incorporation into the polymer backbone or its side chains is the basis for well known methods that lead to great changes in the surface properties [2]. PU is one material that would benefit from the characteristic properties intrinsic to fluorinated polymers. The effect of fluorine-containing PUs on their properties has been described [3][4][5][6][7]. Fluorocarbon chains were incorporated into PUs via fluorine-containing isocyanates [8], chain extenders [3][4][5][6][7] or soft segments [9][10][11]. The surface and bulk structure of the synthesized PUs were studied. Ge at al. [12] synthesized FPUs starting from fluorinated polyether glycol prepared by radical grafting of hexafluoropropylene onto polytetramethylene glycol (PTMG-g-HFP) as a soft segment, 1,6-hexamethylene diisocyanate or toluene diiscyanate as a hard segment and 1,4-butanodiol as a chain extender. They studied their mechanical properties and thermal stability in comparison with those of corresponding hydrogenated PUs along with chemical resistance of FPU films through spot tests with different solvents.
In this research we endeavored to synthesize new poly-and oligourethanes containing fluoropolyether components of different structure both in the backbone and in the side polymer chain. Aromatic and cycloaliphatic diisocyanates were used as hard segments of FPUs. A synthetic route to such FPUs is given in Scheme 1.

Results and Discussion
Polyaddition of diisocyanates to fluorinated alcohols was performed both in solution (dimethylformamide (DMFA) or perfluorobenzene) and in mass (melt) at temperatures varying from 25 °С to 190 °С. Ethylene glycol was utilized as a chain extender in a number of tests. The synthetic conditions are specified in Table 1.
Analyzing the course of the synthesis of FPUs from aromatic and cycloaliphatic diisocyanates, we established that the polyaddition reaction proceeded quite smoothly without a catalyst both in solvents and in the melt. From technological and environmental points of view, the bulk process applied in this research could have the certain advantage against the process in solution. Meanwhile, a number of researchers explained a need for a catalyst by low basicity of fluorinated diols. Apparently, reactivity of fluorinated diols in such reactions does not merely rely on their basicity. Figure 1 shows DSC data for fluoropolyurethane 5, which evidence that the prepared low molecular weight polymer has a partially crystalline structure. DSC curve shows temperature interval from −30 °С to 115 °С corresponding to melting procedure with maximum at 40 °С. Phase regularity of polymer chains is likely to be related to interactions between neighboring macromolecules containing urethane groups. Figure 2 illustrates DSC data for rubberlike high molecular weight FPU 7 obtained from diol 1d and diisocyanate 2с in melt. The glass transition temperature of FPU 7 is −139 °С. An insignificant share of the crystalline phase with the melting point −22 °С was observed herein. It can be concluded that FPU 7 is characterized by a relatively weak intermolecular interaction between C=O and N-H groups of macromolecules. This FPU dissolved only in С6F6, did not dissolve in DMFA and, to some extent, dissolved in acetone.

Results and Discussion
Polyaddition of diisocyanates to fluorinated alcohols was performed both in solution (dimethylformamide (DMFA) or perfluorobenzene) and in mass (melt) at temperatures varying from 25˝C to 190˝C. Ethylene glycol was utilized as a chain extender in a number of tests. The synthetic conditions are specified in Table 1.
Analyzing the course of the synthesis of FPUs from aromatic and cycloaliphatic diisocyanates, we established that the polyaddition reaction proceeded quite smoothly without a catalyst both in solvents and in the melt. From technological and environmental points of view, the bulk process applied in this research could have the certain advantage against the process in solution. Meanwhile, a number of researchers explained a need for a catalyst by low basicity of fluorinated diols. Apparently, reactivity of fluorinated diols in such reactions does not merely rely on their basicity. Figure 1 shows DSC data for fluoropolyurethane 5, which evidence that the prepared low molecular weight polymer has a partially crystalline structure. DSC curve shows temperature interval from´30˝C to 115˝C corresponding to melting procedure with maximum at 40˝C. Phase regularity of polymer chains is likely to be related to interactions between neighboring macromolecules containing urethane groups. Figure 2 illustrates DSC data for rubberlike high molecular weight FPU 7 obtained from diol 1d and diisocyanate 2c in melt. The glass transition temperature of FPU 7 is´139˝C. An insignificant share of the crystalline phase with the melting point´22˝C was observed herein. It can be concluded that FPU 7 is characterized by a relatively weak intermolecular interaction between C=O and N-H groups of macromolecules. This FPU dissolved only in C 6 F 6 , did not dissolve in DMFA and, to some extent, dissolved in acetone.             TGA data indicate that the beginning temperature of polymer destruction is close to 300˝C and maximum rate of destruction is achieved at 460˝C. The TGA results for all other polymers were actually similar and didn 1 t depend on measurement conditions-either in argon or air flow.     Summarizing DSC and TGA data for the selected FPUs synthesized in this research (Table 1), it might be concluded that the temperature interval of FPUs performance (´139˝C to 247-330˝C) is much broader than that of analogous hydrogenated PUs which is normally within´60 to 160˝C depending on the structure of glycols and diisocyanates used as starting materials. Thus, the decomposition onset temperature of PUs prepared from alkylendiisocianates and alkylenglycols is around 250˝C, of PUs from aromatic diisocyanate-alkylene glycol 200˝C, and from alkylenediisocyanate-aromatic glycols 180˝C [21][22][23]. Glass transition temperature (T g ) of these PUs were found to be approximately´60˝C.
The measurement of contact angles on the water-wetted surface of the prepared FPUs was performed as follows. The attained FPU melts were applied to glass plates that were then heated to 90˝C in a desiccator until evaporation of the solvents. Transparent or semitransparent films were prepared. Contact angles of their surface wetting with water were determined. The contact angles achieved 100˝´117˝ (Table 1), which was indicative of rather high hydrophobicity of the coatings.
Syntheses of all other tabulated FPUs were performed in the conditions summarized in Table 1. At rather low temperatures FPUs were synthesized in solution. At high temperatures, the polyaddition process was conducted in the melt. Initial mixture composition includes aromatic diisocyanates (rows 1-6) and cycloaliphatic ones (rows [7][8][9][10][11][12]. Depending on the starting materials and reaction conditions used, the oligomers and polymers obtained exhibit different properties. Some of them (like polymer 5, Figure 1) possess crystal segments of polymer chain, others are rubberlike amorphous materials (7-12 samples). Regardless the difference in structure and properties, all of them were shown to possess pronounced hydrophobic properties (surface wetting contact angles found were higher than 100˝).  [24] and represent fluoropolyether glycols or fluoropolyether amides containing hydroxymethylated terminal groups (1a-b) or a mixture of fluoropolyether glycols with alcohols of similar structure (1c-d) with ratio 7:1. Molecular weights and compositions of the prepared fluoropolyether diols and alcohols were found from 19 F-NMR and 1 H-NMR data. 1 H-NMR and 19 F-NMR were using a Bruker AM 300 SF at 300 MHz ( 1 H), 282,40 MHz ( 19 F). 1 H-NMR chemical shifts were referenced to the residual proton signal from CDCl 3 served as an internal standard. 19 F-NMR spectra (solutions in C 6 F 6 ,´163 ppm) served as an inside standard. Multiplicities are reported as singlet (s), doublet (d), triplet (t) and some combinations of these, multiplet (m).

Materials and Methods
The molecular weight characteristics of the polymers were determined using the gel permeation chromatography (GPC) method in DMFA at 35˝C on a Knauer liquid chromatograph equipped with a refractometer RI-2300 and three columns (Waters Styrogel HT-2, HT-4, and HT-6E). The elution rate 1 mL/min. The calibration was done using the polystyrene standard (PL Polymer Laboratories) in the range from 1250 to 1030000 Da.
The glass transition temperature was determined by the differential scanning calorimetry (DSC) on a DSC-822e instrument (Mettler Toledo, Switzerland) using~10 mg samples at the heating rate 10˝C/min. IR spectra were registered on a Specord IR-75 spectrometer.
TGA data were determined on the instrument Derivatograph-C (MOM, Hungary) in air and argon flow using~15 mg samples at the heating rate 10˝C/min. Inherent viscosity was determined using an Ubbelohde viscometer in DMFA or C 6 F 6 .

Synthesis of Fluoropolyurethane 7
Diol 1c (2.46 g, 0.001 mol) pre-heated at 110˝C (18 Torr) during 2 h was placed in a four-neck flask fitted with a stirrer, drop funnel, thermometer, and dry nitrogen feeder and then 0.27 g (0.001 mol) of diisocyanate 2c was added. The process was conducted with intensive stirring in the dry nitrogen flow, gradually increasing the temperature from 25˝C to 190˝C, during 50 h. A homogeneous, thick, colorless and transparent mass was prepared. The reaction completion was monitored against the absence of the free NCO group absorption band in the region of 2270 cm´1, T g =´139˝C (Figure 2), T 5% decomp. = 300˝C. Maximum decomposition rate was « 450˝C (Figure 3).

Conclusions
Novel FPUs possessing promising performance properties have been synthesized starting from fluorinated diols as soft segments and both aromatic and cycloaliphatic diisocyanates as hard segments. Values of their glass transition temperature and the beginning temperature of thermal decomposition achieve´139˝C and 247-330˝C, correspondingly, showing their performance in quite wide temperature intervals in comparison to non-fluorinated analogs. According to literature data, the temperature interval of hydrogenated PUs performance is predominately in the range from´60˝C to 160˝C.
Contact angles of surface wetting with water for FPUs obtained reach 100-117˝, providing evidence of quite favorable hydrophobic properties of fluorinated polyurethanes. Potentially, novel fluorinated polyurethanes can be used for production of materials exploited under extreme conditions and in compositions of complex organic and hybrid molecular systems [25,26].