Search Results

The Slave River is a northern river in Canada, with ice being an important component of its flow regime for at least half of the year. During the spring breakup period, ice jams and ice-jam flooding can occur in the Slave River Delta, which is of benefit for the replenishment of moisture and sediment required to maintain the ecological integrity of the delta. To better understand the ice jam processes that lead to flooding, as well as the replenishment of the delta, the one-dimensional hydraulic river ice model RIVICE was implemented to simulate and explore ice jam formation in the Slave River Delta. Incoming ice volume, a crucial input parameter for RIVICE, was determined by the novel approach of using MODIS space-born remote sensing imagery. Space-borne and air-borne remote sensing data were used to parameterize the upstream ice volume available for ice jamming. Gauged data was used to complement modeling calibration and validation. HEC-RAS, another one-dimensional hydrodynamic model, was used to determine ice volumes required for equilibrium jams and the upper limit of ice volume that a jam can sustain, as well as being used as a threshold for the volumes estimated by the dynamic ice jam simulations using RIVICE. Parameter sensitivity analysis shows that morphological and hydraulic properties have great impacts on the ice jam length and water depth in the Slave River Delta. Full article

A simple and sensitive cyclodextrin-micellar electrokinetic capillary chromatography (CD-MEKC) method with UV detection was developed and validated for the determination of vancomycin (VCM) in serum. The separation was achieved in 14 min at 25 °C with a fused-silica capillary column of 40.2 cm × 75 μm i.d. (effective length 30.2 cm) and a run buffer containing 25 mM borate buffer with 50 mM sodium dodecylsulfonate (SDS) (pH 9.5) and 2% sulfobutyl-β-cyclodextrin (sulfobutyl-β-CD). Under optimal conditions for biological samples, good separations with high efficiency and short analysis time were achieved. Several parameters affecting the drug separation from biological matrices were studied, including buffer types, concentrations, and pHs. The methods were validated over the range of 0.9998–99.98 µg/mL. Calibration curves of VCM also showed good linearity (r² > 0.999). Intra- and interday precisions (relative standard deviation, RSD) were less than 5.80% and 7.38%, and lower limit of quantification (LLOQ) were lower than 1.0 μg/mL. The mean recoveries ranged between 84.03% and 91.69%. The method was successfully applied for monitoring VCM concentrations in serum of patients with peritoneal dialysis-associated peritonitis (PDAP). The assay should be applicable to pharmacokinetic studies and routine therapeutic drug monitoring of this drug in serum. Full article

Breast cancer is one of the most frequently diagnosed cancers in females worldwide and lacks specific biomarkers for early detection. In a previous study, we obtained a selective RNA-cleaving Fluorogenic DNAzyme (RFD) probe against MDA-MB-231 cells, typical breast cancer cells, through the systematic evolution of ligands by exponential process (SELEX). To improve the performance of this probe for actual application, we carried out a series of optimization experiments on the pH value of a reaction buffer, the type and concentration of cofactor ions, and sequence minimization. The length of the active domain of the probe reduced to 25 nt from 40 nt after optimization, which was synthesized more easily and economically. The detection limit of the optimized assay system was 2000 MDA-MB-231 cells in 30 min, which is more sensitive than the previous one (almost 5000 cells). The DNAzyme probe was also capable of distinguishing MDA-MB-231 cell specifically from 3 normal cells and 10 other tumor cells. This probe with high sensitivity, selectivity, and economic efficiency enhances the feasibility for further clinical application in breast cancer diagnosis. Herein, we developed an optimization system to produce a general strategy to establish an easy-to-use DNAzyme-based assay for other targets. Full article

High-velocity transverse impact of ballistic fabrics and yarns by projectiles subject individual fibers to multi-axial dynamic loading. Single-fiber transverse impact experiments with the current state-of-the-art experimental capabilities are challenging due to the associated micron length-scale. Kevlar^® KM2 fibers exhibit a nonlinear inelastic behavior in transverse compression with an elastic limit less than 1.5% strain. The effect of this transverse behavior on a single KM2 fiber subjected to a cylindrical and a fragment-simulating projectile (FSP) transverse impact is studied with a 3D finite element model. The inelastic behavior results in a significant reduction of fiber bounce velocity and projectile-fiber contact forces up to 38% compared to an elastic impact response. The multiaxial stress states during impact including transverse compression, axial tension, axial compression and interlaminar shear are presented at the location of failure. In addition, the models show a strain concentration over a small length in the fiber under the projectile-fiber contact. A failure criterion, based on maximum axial tensile strain accounting for the gage length, strain rate and multiaxial loading degradation effects are applied to predict the single-fiber breaking speed. Results are compared to the elastic response to assess the importance of inelastic material behavior on failure during a transverse impact. Full article

Understanding the effects that the Urban Heat Island (UHI) has on plant phenology is important in predicting ecological impacts of expanding cities and the impacts of the projected global warming. However, the underlying methods to monitor phenological events often limit this understanding. Generally, one can either have a small sample of in situ measurements or use satellite data to observe large areas of land surface phenology (LSP). In the latter, a tradeoff exists among platforms with some allowing better temporal resolution to pick up discrete events and others possessing the spatial resolution appropriate for observing heterogeneous landscapes, such as urban areas. To overcome these limitations, we applied the Spatial and Temporal Adaptive Reflectance Model (STARFM) to fuse Landsat surface reflectance and MODIS nadir BRDF-adjusted reflectance (NBAR) data with three separate selection conditions for input data across two versions of the software. From the fused images, we derived a time-series of high temporal and high spatial resolution synthetic Normalized Difference Vegetation Index (NDVI) imagery to identify the dates of the start of the growing season (SOS), end of the season (EOS), and the length of the season (LOS). The results were compared between the urban and exurban developed areas within the vicinity of Ogden, UT and across all three data scenarios. The results generally show an earlier urban SOS, later urban EOS, and longer urban LOS, with variation across the results suggesting that phenological parameters are sensitive to input changes. Although there was strong evidence that STARFM has the potential to produce images capable of capturing the UHI effect on phenology, we recommend that future work refine the proposed methods and compare the results against ground events. Full article

Studies of spatial genetic structure (SGS) are important because they offer detailed insights into historical demographic and evolutionary processes and provide important information regarding species conservation and management. Pinus engelmannii and P. leiophylla var. leiophylla are two important timber tree species in Mexico, covering about 2.5 and 1.9 million hectares, respectively. However, studies in relation to population genetics are unfortunately scant. The aim of this research was to use amplified fragment length polymorphisms (AFLP) analysis to identify potential differences in spatial genetic structure within and among seven Pinus engelmannii and nine P. leiophylla var. leiophylla seed stands in Durango, Mexico. Within the 16 seed stands of the two tested pine species, no significant SGS was detected, although SGS was detected among the seed stands. We concluded that the collection of seed in only some seed stands should not significantly alter the degree of genetic differentiation within the (collected) seed. Distances between seed orchards and pollen propagators of more than 24 km for P. engelmannii and 7 km for P. leiophylla may be sufficient to limit contamination. Finally, local seeds should be used for (re)forestation. Full article

In this work, we deal with the autonomy issue in the perturbation expansion for the eigenfunctions of a compact Hilbert–Schmidt integral operator. Here, the autonomy points to the perturbation expansion coefficients of the relevant eigenfunction not depending on the perturbation parameter explicitly, but the dependence on this parameter arises from the coordinate change at the zero interval limit. Moreover, the related half interval length is utilized as the perturbation parameter in the perturbative analyses. Thus, the zero interval limit perturbation for solving the eigenproblem under consideration is developed. The aim of this work is to show that the autonomy imposition brings an important restriction on the kernel of the corresponding integral operator, and the constructed perturbation series is not capable of expressing the exact solution approximately unless a specific type of kernel is considered. The general structure for the encountered constraints is revealed, and the specific class of kernels is identified to this end. Error analysis of the developed method is given. These analyses are also supported by certain illustrative implementations involving the kernels, which are and are not in the specific class addressed above. Thus, the efficiency of the developed method is shown, and the relevant analyses are confirmed. Full article

In China, a flashing green (FG) indication of 3 s followed by a yellow (Y) indication of 3 s is commonly applied to end the green phase at signalized intersections. Stop-line crossing behavior of drivers during such a phase transition period significantly influences safety performance of signalized intersections. The objective of this study is thus to empirically analyze and model drivers’ stop-line crossing time and speed in response to the specific phase transition period of FG and Y. High-resolution trajectories for 1465 vehicles were collected at three rural high-speed intersections with a speed limit of 80 km/h and two urban intersections with a speed limit of 50 km/h in Shanghai. With the vehicle trajectory data, statistical analyses were performed to look into the general characteristics of stop-line crossing time and speed at the two types of intersections. A multinomial logit model and a multiple linear regression model were then developed to predict the stop-line crossing patterns and speeds respectively. It was found that the percentage of stop-line crossings during the Y interval is remarkably higher and the stop-line crossing time is approximately 0.7 s longer at the urban intersections, as compared with the rural intersections. In addition, approaching speed and distance to the stop-line at the onset of FG as well as area type significantly affect the percentages of stop-line crossings during the FG and Y intervals. Vehicle type and stop-line crossing pattern were found to significantly influence the stop-line crossing speed, in addition to the above factors. The red-light-running seems to occur more frequently at the large intersections with a long cycle length. Full article

The recently developed nanobainitic steels show high strength as well as high ductility. Although this combination seems to be promising for fatigue design, fatigue properties of nanostructured bainitic steels are often surprisingly low. To improve the fatigue behavior, an understanding of the correlation between the nanobainitic microstructure and the fatigue limit is fundamental. Therefore, our hypothesis to predict the fatigue limit was that the main function of the microstructure is not necessarily totally avoiding the initiation of a fatigue crack, but the microstructure has to increase the ability to decelerate or to stop a growing fatigue crack. Thus, the key to understanding the fatigue behavior of nanostructured bainite is to understand the role of the microstructural features that could act as barriers for growing fatigue cracks. To prove this hypothesis, we carried out fatigue tests, crack growth experiments, and correlated these results to the size of microstructural features gained from microstructural analysis by light optical microscope and EBSD-measurements. Finally, we were able to identify microstructural features that influence the fatigue crack growth and the fatigue limit of nanostructured bainitic steels. Full article

A electrochemical sensor for the highly sensitive detection of tetrabromobisphenol A (TBBPA) was fabricated based on acetylene black paste electrode (ABPE) modified with 3-(N,N-Dimethylpalmitylammonio) propanesulfonate (SB3-16) in this study. The peak current of TBBPA was significantly enhanced at SB3-16/ABPE compared with unmodified electrodes. To further improve the electrochemical performance of the modified electrode, corresponding experimental parameters such as the length of hydrophobic chains of zwitterionic surfactant, the concentration of SB3-16, pH value, and accumulation time were examined. The peak currents of TBBPA were found to be linearly correlated with its concentrations in the range of 1 nM to 1 µM, with a detection limit of 0.4 nM. Besides, a possible mechanism was also discussed, and the hydrophobic interaction between TBBPA and the surfactants was suggested to take a leading role in enhancing the responses. Finally, this sensor was successfully employed to detect TBBPA in water samples. Full article

In this work, the effect of Ag⁺ on DNA sensitized Tb³⁺ luminescence was studied initially using the Ag⁺-specific RNA-cleaving DNAzyme, Ag10c. While we expected to observe luminescence quenching by Ag⁺, a significant enhancement was produced. Based on this observation, simple DNA oligonucleotide homopolymers were used with systematically varied sequence and length. We discovered that both poly-G and poly-T DNA have a significant emission enhancement by Ag⁺, while the absolute intensity is stronger with the poly-G DNA, indicating that a G-quadruplex DNA is not required for this enhancement. Using the optimized length of the G7 DNA (an oligo constituted with seven guanines), Ag⁺ was measured with a detection limit of 57.6 nM. The signaling kinetics, G7 DNA conformation, and the binding affinity of Tb³⁺ to the DNA in the presence or absence of Ag⁺ are also studied to reveal the mechanism of emission enhancement. This observation is useful not only for label-free detection of Ag⁺, but also interesting for the rational design of new biosensors using Tb³⁺ luminescence. Full article

A PCR-free, optics-free device is used for the detection of Escherichia coli (E. coli) 16S rRNA at 10 fM, which corresponds to ~100–1000 colony forming units/mL (CFU/mL) depending on cellular rRNA levels. The development of a rapid, sensitive, and cost-effective nucleic acid detection platform is sought for the detection of pathogenic microbes in food, water and body fluids. Since 16S rRNA sequences are species specific and are present at high copy number in viable cells, these nucleic acids offer an attractive target for microbial pathogen detection schemes. Here, target 16S rRNA of E. coli at 10 fM concentration was detected against a total RNA background using a conceptually simple approach based on electromechanical signal transduction, whereby a step change reduction in ionic current through a pore indicates blockage by an electrophoretically mobilized bead-peptide nucleic acid probe conjugate hybridized to target nucleic acid. We investigated the concentration detection limit for bacterial species-specific 16S rRNA at 1 pM to 1 fM and found a limit of detection of 10 fM for our device, which is consistent with our previous finding with single-stranded DNA of similar length. In addition, no false positive responses were obtained with control RNA and no false negatives with target 16S rRNA present down to the limit of detection (LOD) of 10 fM. Thus, this detection scheme shows promise for integration into portable, low-cost systems for rapid detection of pathogenic microbes in food, water and body fluids. Full article

We develop an analytical model to predict the collapse conformation for a single semiflexible polymer chain in solution, given its length, diameter, stiffness, and self-attractiveness. We construct conformational phase diagrams containing three collapsed states, namely torus, bundle, and globule over a range of dimensionless ratios of the three energy parameters, namely solvent-water surface energy ( ${\mathsf{\gamma }}_{\mathrm{s}}$ ), energy of bundle end folds ( ${\mathsf{\gamma }}_{\mathrm{e}}$ ), and bending energy per unit length in a torus ( ${\mathsf{\gamma }}_{\mathrm{b}}$ ). Our phase diagram captures the general phase behavior of a single long chain (>10 Kuhn lengths) at moderately high (order unity) dimensionless temperature, which is the ratio of thermal energy to the attractive interaction between neighboring monomers. We find that the phase behavior approaches an asymptotic limit when the dimensionless chain length to diameter ratio (L*) exceeds 300. We successfully validate our analytical results with Brownian Dynamics (BD) simulations, using a mapping of the simulation parameters to those used in the phase diagram. We evaluate the effect of three different bending potentials in the range of moderately high dimensionless temperature, a regime not been previously explored by simulations, and find qualitative agreement between the model and simulation results. We, thus, demonstrate that a rather simplified analytical model can be used to qualitatively predict the final collapsed state of a given polymer chain. Full article

Eczema is a common skin condition that impairs children’s daily life activities and quality of life. Previous research shows that gut microbiome composition plays an important role in the development of eczema. The present review summarizes evidence on environmental factors related to altered gut microbiota in children with eczema. We searched Medline, PubMed, Embase, and the Cochrane database of Systematic Reviews through October 2015. The search strategy focused on articles published in peer-reviewed, English-language journals with no publication year limit. Only original studies and review articles that reported environmental factors on gut microbiome specific to eczema were included in this review. We selected six studies (total 1990 participants) for full review and identified that the composition of gut microbiota specific to eczema could be influenced by the following environmental factors: length of gestation, mode of delivery, type of feeding, method of treatment, number of older siblings, and other lifestyle factors. There has been inconsistent empirical evidence as to the modulatory effects of gut microbiota on immunological functions in children with eczema. Further research on the environmental-host-microbial interaction is needed to develop a strong base of knowledge for the development and implementation of prevention strategies and policies for eczema. Full article

Wildfire number and burned area temporal dynamics within all of Siberia and along a south-north transect in central Siberia (45°–73° N) were studied based on NOAA/AVHRR (National Oceanic and Atmospheric Administration/ Advanced Very High Resolution Radiometer) and Terra/MODIS (Moderate Resolution Imaging Spectroradiometer) data and field measurements for the period 1996–2015. In addition, fire return interval (FRI) along the south-north transect was analyzed. Both the number of forest fires and the size of the burned area increased during recent decades (p < 0.05). Significant correlations were found between forest fires, burned areas and air temperature (r = 0.5) and drought index (The Standardized Precipitation Evapotranspiration Index, SPEI) (r = −0.43). Within larch stands along the transect, wildfire frequency was strongly correlated with incoming solar radiation (r = 0.91). Fire danger period length decreased linearly from south to north along the transect. Fire return interval increased from 80 years at 62° N to 200 years at the Arctic Circle (66°33’ N), and to about 300 years near the northern limit of closed forest stands (about 71°+ N). That increase was negatively correlated with incoming solar radiation (r = −0.95). Full article

Genetic modification (“transfection”) of mammalian cells using non-viral, synthetic agents such as polycations, is still a challenge. Polyplex formation between the DNA and the polycation is a decisive step in such experiments. Star-shaped polycations have been proposed as superior transfection agents, yet have never before been compared side-by-side, e.g., in view of structural effects. Herein four star-shaped polycationic structures, all based on (2-dimethylamino) ethyl methacrylate (DMAEMA) building blocks, were investigated for their potential to deliver DNA to adherent (CHO, L929, HEK-293) and non-adherent (Jurkat, primary human T lymphocytes) mammalian cells. The investigated vectors included three structures where the PDMAEMA arms (different arm length and grafting densities) had been grown from a center silsesquioxane or silica-coated γ-Fe₂O₃-core and one micellar structure self-assembled from poly(1,2-butadiene)-block PDMAEMA polymers. All nano-stars combined high transfection potential with excellent biocompatibility. The micelles slightly outperformed the covalently linked agents. For method development and optimization, the absolute amount of polycation added to the cells was more important than the N/P-ratio (ratio between polycation nitrogen and DNA phosphate), provided a lower limit was passed and enough polycation was present to overcompensate the negative charge of the plasmid DNA. Finally, the matrix (NaCl vs. HEPES-buffered glucose solution), but also the concentrations adjusted during polyplex formation, affected the results. Full article

Most distributed-generation facilities are performed on pre-built distribution grids. The design conditions of these existing grids may limit the ability of new users to get a connection due to technical and/or cost constraints. This work proposes a simple solution, adjusted to the relevant regulations and embodied in a radial distribution grid of Spanish low voltage, to improve the interconnection of distributed generation, usually grid connected photovoltaic systems. The proposed solution, based on increasing the section of the neutral line, achieves a capacity of increasing the length of the supply grid by more than 20%. Full article

The space of one-dimensional disordered interacting quantum models displaying a many-body localization (MBL) transition seems sufficiently rich to produce critical points with level statistics interpolating continuously between the Poisson statistics of the localized phase and the Wigner–Dyson statistics of the delocalized phase. In this paper, we consider the strong disorder limit of the MBL transition, where the level statistics at the MBL critical point is close to the Poisson statistics. We analyze a one-dimensional quantum spin model, in order to determine the statistical properties of the rare extensive resonances that are needed to destabilize the MBL phase. At criticality, we find that the entanglement entropy can grow with an exponent $0<\alpha <1$ anywhere between the area law $\alpha =0$ and the volume law $\alpha =1$ , as a function of the resonances properties, while the entanglement spectrum follows the strong multifractality statistics. In the MBL phase near criticality, we obtain the simple value $\nu =1$ for the correlation length exponent. Independently of the strong disorder limit, we explain why, for the many-body localization transition concerning individual eigenstates, the correlation length exponent ν is not constrained by the usual Harris inequality $\nu \ge 2/d$ , so that there is no theoretical inconsistency with the best numerical measure $\nu =0.8\left(3\right)$ obtained by Luitz et al. (2015). Full article

The distribution of word probabilities in the monkey model of Zipf’s law is associated with two universality properties: (1) the exponent in the approximate power law approaches −1 as the alphabet size increases and the letter probabilities are specified as the spacings from a random division of the unit interval for any distribution with a bounded density function on [0,1] ; and (2), on a logarithmic scale the version of the model with a finite word length cutoff and unequal letter probabilities is approximately normally distributed in the part of the distribution away from the tails. The first property is proved using a remarkably general limit theorem from Shao and Hahn for the logarithm of sample spacings constructed on [0,1] and the second property follows from Anscombe’s central limit theorem for a random number of independent and identically distributed (i.i.d.) random variables. The finite word length model leads to a hybrid Zipf-lognormal mixture distribution closely related to work in other areas. Full article

The potential of optical remote sensing data to identify, map and monitor croplands is well recognized. However, clouds strongly limit the usefulness of optical imagery for these applications. This paper aims at assessing cloud cover conditions over four states in the tropical and sub-tropical Center-South region of Brazil to guide the development of an appropriate agricultural monitoring system based on Landsat-like imagery. Cloudiness was assessed during overlapping four months periods to match the typical length of crop cycles in the study area. The percentage of clear sky occurrence was computed from the 1 km resolution MODIS Cloud Mask product (MOD35) considering 14 years of data between July 2000 and June 2014. Results showed high seasonality of cloud occurrence within the crop year with strong variations across the study area. The maximum seasonality was observed for the two states in the northern part of the study area (i.e., the ones closer to the Equator line), which also presented the lowest averaged values (15%) of clear sky occurrence during the main (summer) cropping period (November to February). In these locations, optical data faces severe constraints for mapping summer crops. On the other hand, relatively favorable conditions were found in the southern part of the study region. In the South, clear sky values of around 45% were found and no significant clear sky seasonality was observed. Results underpin the challenges to implement an operational crop monitoring system based solely on optical remote sensing imagery in tropical and sub-tropical regions, in particular if short-cycle crops have to be monitored during the cloudy summer months. To cope with cloudiness issues, we recommend the use of new systems with higher repetition rates such as Sentinel-2. For local studies, Unmanned Aircraft Vehicles (UAVs) might be used to augment the observing capability. Multi-sensor approaches combining optical and microwave data can be another option. In cases where wall-to-wall maps are not mandatory, statistical sampling approaches might also be a suitable alternative for obtaining useful crop area information. Full article

In previous works on authentic samples of saffron of known history (harvest and processing year, storage conditions, and length of time) some biomarkers were proposed using both FT-IR and NMR metabolomics regarding the shelf life of the product. This work addresses the difficulties to trace back the “age” of commercial saffron samples of unknown history, sets a limit value above which these products can be considered substandard, and offers a useful tool to combat saffron mislabeling and fraud with low-quality saffron material. Investigations of authentic and commercial saffron samples of different origin and harvest year, which had been stored under controlled conditions for different lengths of time, allowed a clear-cut clustering of samples in two groups according to the storage period irrespectively of the provenience. In this respect, the four-year cut off point proposed in our previous work assisted to trace back the “age” of unknown samples and to check for possible mislabeling practices. Full article

A room-temperature continuous-wave (CW) quantum cascade laser (QCL)-based methane (CH₄) sensor operating in the mid-infrared near 8 μm was developed for continuous measurement of CH₄ concentrations in ambient air. The well-isolated absorption line (7F_2,4 ← 8F_1,2) of the ν₄ fundamental band of CH₄ located at 1255.0004 cm⁻¹ was used for optical measurement of CH₄ concentration by direct absorption in a White-type multipass cell with an effective path-length of 175 m. A 1σ (SNR = 1) detection limit of 33.3 ppb in 218 s was achieved with a measurement precision of 1.13%. The developed sensor was deployed in a campaign of measurements of time series CH₄ concentration on a site near a suburban traffic road in Dunkirk (France) from 9th to 22nd January 2013. An episode of high CH₄ concentration of up to ~3 ppm has been observed and analyzed with the help of meteorological parameters combined with back trajectory calculation using the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model of NOAA. Full article

A fluidic microchip incorporating a convergent microchannel and a Nafion-nanoporous membrane is proposed for the preconcentration and separation of multi-species samples on a single platform. In the device, sample preconcentration is achieved by means of the ion concentration polarization effect induced at the micro/nano interface under the application of an external electric field, while species separation is achieved by exploiting the different electrophoretic mobilities of the sample components. The experimental results show that the device is capable of detecting C-reactive protein (CRP) with an initial concentration as low as 9.50 × 10⁻⁶ mg/L given a sufficient preconcentration time and driving voltage. In addition, it is shown that a mixed-species sample consisting of three negatively-charged components (bovine serum albumin (BSA), tetramethylrhodamine(TAMRA) isothiocyanate-Dextran and fluorescent polymer beads) can be separated and preconcentrated within 20 min given a driving voltage of 100 V across 1 cm microchannel in length. In general, the present results confirm the feasibility of the device for the immunoassay or detection of various multi-species samples under low concentration in the biochemical and biomedical fields. The novel device can therefore improve the detection limit of traditional medical facilities. Full article

The fact that the equations of motion for matter remain invariant when a constant is added to the Lagrangian suggests postulating that the field equations of gravity should also respect this symmetry. This principle implies that: (1) the metric cannot be varied in any extremum principle to obtain the field equations; and (2) the stress-tensor of matter should appear in the variational principle through the combination T_abn^an^b where n_a is an auxiliary null vector field, which could be varied to get the field equations. This procedure uniquely selects the Lanczos–Lovelock models of gravity in D-dimensions and Einstein’s theory in D = 4. Identifying na with the normals to the null surfaces in the spacetime in the macroscopic limit leads to a thermodynamic interpretation for gravity. Several geometrical variables and the equation describing the spacetime evolution acquire a thermodynamic interpretation. Extending these ideas one level deeper, we can obtain this variational principle from a distribution function for the “atoms of spacetime”, which counts the number of microscopic degrees of freedom of the geometry. This is based on the curious fact that the renormalized spacetime endows each event with zero volume, but finite area! Full article

Accurate mapping and measurement of erosion channels is necessary to accurately estimate the impact of channeled erosion in an area. Field surveys can provide optimal quantitative results, but they are only applicable to small areas. Recently, photogrammetric techniques have been applied to small format aerial photographs that were taken by UAVs. Few studies have applied photogrammetry for mapping and measuring single permanent gullies using very high resolution stereoscopic satellite images. We explore the use of such images to map rills and ephemeral gullies and to measure the length, width and depth of individual erosion channels to estimate the eroded volumes. The proposed methodology was applied to the Collazzone area of Central Italy. All of the channel characteristics were determined using GeoEye-1^® panchromatic stereoscopic satellite images of the 48-km² study area and a 3D floating cursor. We identified, mapped, and measured the lengths of 555 channel segments. The top width and depth could be measured in only a subset of the channel segments (the SMC subset). The SMC data were used to determine the coefficients of the power law relationship between the rill/gully volume and length (V = aL^b) and the uncertainties due to the channel depth measurements and the cross-sectional shape. The field data of the rill and gully volumes were within the estimated uncertainty. We defined a decision rule to distinguish rills from gullies on the basis of the segment length and applied the corresponding power law relationship that was derived from the SMC subset to estimate the eroded volume of the entire dataset. The erosion values that were calculated at different scales (0.680 Mg∙ha⁻¹ at the catchment scale, 28.4 Mg∙ha⁻¹ on the parcels affected by erosion) are consistent with values found in the literature. Our results indicate that erosion at the catchment scale can be considered moderate, whereas the erosion at the field scale exceeds the tolerance limit, which is consistent with data that have been summarized and/or discussed by several authors. Full article

In this paper, vertically aligned Pt nanowire arrays (PtNWA) with different lengths and surface roughnesses were fabricated and their electrochemical performance toward hydrogen peroxide (H₂O₂) detection was studied. The nanowire arrays were synthesized by electroplating Pt in nanopores of anodic aluminum oxide (AAO) template. Different parameters, such as current density and deposition time, were precisely controlled to synthesize nanowires with different surface roughnesses and various lengths from 3 μm to 12 μm. The PtNWA electrodes showed better performance than the conventional electrodes modified by Pt nanowires randomly dispersed on the electrode surface. The results indicate that both the length and surface roughness can affect the sensing performance of vertically aligned Pt nanowire array electrodes. Generally, longer nanowires with rougher surfaces showed better electrochemical sensing performance. The 12 μm rough surface PtNWA presented the largest sensitivity (654 μA·mM⁻¹·cm⁻²) among all the nanowires studied, and showed a limit of detection of 2.4 μM. The 12 μm rough surface PtNWA electrode also showed good anti-interference property from chemicals that are typically present in the biological samples such as ascorbic, uric acid, citric acid, and glucose. The sensing performance in real samples (river water) was tested and good recovery was observed. These Nafion-free, vertically aligned Pt nanowires with surface roughness control show great promise as versatile electrochemical sensors and biosensors. Full article

A high-sensitivity Mach-Zehnder interferometer (MZI) biochemical sensing platform based on Silicon-in-insulator (SOI) rib waveguide with large cross section is proposed in this paper. Based on the analyses of the evanescent field intensity, the mode polarization and cross section dimensions of the SOI rib waveguide are optimized through finite difference method (FDM) simulation. To realize high-resolution MZI read-out configuration based on the SOI rib waveguide, medium-filled trenches are employed and their performances are simulated through two-dimensional finite-difference-time domain (2D-FDTD) method. With the fundamental EH-polarized mode of the SOI rib waveguide with a total rib height of 10 μm, an outside rib height of 5 μm and a rib width of 2.5 μm at the operating wavelength of 1550 nm, when the length of the sensitive window in the MZI configuration is 10 mm, a homogeneous sensitivity of 7296.6%/refractive index unit (RIU) is obtained. Supposing the resolutions of the photoelectric detectors connected to the output ports are 0.2%, the MZI sensor can achieve a detection limit of 2.74 × 10⁻⁶ RIU. Due to high coupling efficiency of SOI rib waveguide with large cross section with standard single-mode glass optical fiber, the proposed MZI sensing platform can be conveniently integrated with optical fiber communication systems and (opto-) electronic systems, and therefore has the potential to realize remote sensing, in situ real-time detecting, and possible applications in the internet of things. Full article

Five measurements of claw conformation (toe angle, claw height, claw width, toe length and abaxial groove length) taken directly from the hoof were compared with the measurements taken from digital images of the same claws. Concordance correlation coefficients and limits-of-agreement analysis showed that, for four of the five measures (claw height, claw width, toe length and abaxial groove length), agreement was too poor for digital and manual measures to be used interchangeably. For all four of these measures, Liao’s modified concordance correlation coefficient (mCCC) was ≤0.4, indicating poor concordance despite Pearson’s correlation being >0.6 in all cases. The worst concordance was seen for toe length (mCCC = 0.13). Limits-of-agreement analysis showed that, for all four measures, there was a large variation in the difference between the manual and digital methods, even when the effect of mean on difference was accounted for, with the 95% limits-of-agreement for the four measures being further away from the mean difference than 10% of the mean in all four cases. The only one of the five measures with an acceptable concordance between digital and manual measurement was toe angle (mCCC = 0.81). Nevertheless, the limits-of-agreement analysis showed that there was a systematic bias with, on average, the manual measure of toe angle, being 2.1° smaller than the digital. The 95% limits-of-agreement for toe angle were ±3.4°, probably at the upper limit of what is acceptable. However, the lack of data on the variability of individual measurements of claw conformation means that it is unclear how this variability compares to measurement of toe angle in the same animal using the same or a different manual technique. Full article

Solid bar microextraction (SBME), followed by liquid chromatography with fluorescence detection (HPLC-FLD), for the quantification of ochratoxin A in wheat and maize was developed. Ground wheat and maize grains were extracted with acetonitrile-water-acetic acid (79:20:1, v/v/v), followed by defatting with cyclohexane, and subjected to SBME-LC-FLD analysis. SBME devices were constructed by packing 2 mg sorbent (C18) into porous polypropylene micro-tubes (2.5 cm length, 600 μm i.d., and 0.2 μm pore size). SBME devices were conditioned with methanol and placed into 5 mL stirred sample solutions for 70 min. After extraction, OTA was desorbed into 200 μL of methanol for 15 min, the solution was removed in vacuum, the residue was dissolved in 50 μL of methanol-water (1:1, v/v) and ochratoxin A content was determined by HPLC-FLD. Under optimized extraction conditions, the limit of detection of 0.9 μg·kg⁻¹ and 2.5 μg·kg⁻¹ and the precision of 3.4% and 5.0% over a concentration range of 1 to 100 μg·kg⁻¹ in wheat and maize flour, respectively, were obtained. Full article

In this paper, we investigate a lossy source coding problem, where an upper limit on the permitted distortion is defined for every dataset element. It can be seen as an alternative approach to rate distortion theory where a bound on the allowed average error is specified. In order to find the entropy, which gives a statistical length of source code compatible with a fixed distortion bound, a corresponding optimization problem has to be solved. First, we show how to simplify this general optimization by reducing the number of coding partitions, which are irrelevant for the entropy calculation. In our main result, we present a fast and feasible for implementation greedy algorithm, which allows one to approximate the entropy within an additive error term of log2 e. The proof is based on the minimum entropy set cover problem, for which a similar bound was obtained. Full article

We report an ultra-sensitive and robust fluorescence sensor made by using a biconical taper with a waist diameter of 720 nm for both excitation and fluorescence collection. To enhance the stability of the fluorescence sensor, the biconical taper has been embedded in a 125 µm wide microchannel with a detection length of 2.5 cm. Investigated by measuring the fluorescence intensity of rhodamine 6G (R6G), the sensor shows a detection limit down to 100 pM, with excellent reversibility in a concentration range of 0–10 nM. The sensor has also been applied to quantum dot (QD)-labeled streptavidin measurements, yielding a detection sensitivity down to 10 pM for QDs. In addition, the small sample volume (ca. 500 nL), high sampling throughput, and seamless connection between the biconical taper and standard optical fibers offer a number of attractive advantages for chemical and biosensing applications. Full article

Terrestrial laser scanning can provide high-resolution, two-dimensional sampling of soil surface roughness. While previous studies demonstrated the usefulness of these roughness measurements in geophysical applications, questions about the number of required scans and their resolution were not investigated thoroughly. Here, we suggest a method to generate digital elevation models, while preserving the surface’s stochastic properties at high frequencies and additionally providing an estimate of their spatial resolution. We also study the impact of the number and positions of scans on roughness indices’ estimates. An experiment over a smooth and isotropic soil plot accompanies the analysis, where scanning results are compared to results from active triangulation. The roughness measurement conditions for ideal sampling are revisited and updated for diffraction-limited sampling valid for close-range laser scanning over smooth and isotropic soil roughness. Our results show that terrestrial laser scanning can be readily used for roughness assessment on scales larger than 5 cm, while for smaller scales, special processing is required to mitigate the effect of the laser beam footprint. Interestingly, classical roughness parametrization (correlation length, root mean square height (RMSh)) was not sensitive to these effects. Furthermore, comparing the classical roughness parametrization between one- and four-scan setups shows that the one-scan data can replace the four-scan setup with a relative loss of accuracy below 1% for ranges up to 3 m and incidence angles no larger than 50°, while two opposite scans can replace it over the whole plot. The incidence angle limit for the spectral slope is even stronger and is 40°. These findings are valid for scanning over smooth and isotropic soil roughness. Full article

Researchers have become increasingly interested in the health patterns of immigrants with longer residence in the United States, as this reveals the health consequences of integration processes. The negative acculturation effect has been the dominant interpretation of duration patterns, despite empirical and theoretical uncertainties about this assumption. This theory assumes that immigrant health declines with longer residence in the United States because of poorer health behaviors and health risks that reflect Americanized lifestyles. This paper reviews the empirical support for the negative acculturation theory among Asian immigrants to determine if and when it is an appropriate interpretation for duration patterns. I conclude that empirical inconsistencies and methodological issues limit the negative acculturation theory as the primary interpretation for duration patterns. First, there is no consistent evidence that health behaviors decline with time. There is also substantial group heterogeneity in duration patterns as well as heterogeneity across health outcomes. The literature has not adequately addressed methodological shortcomings, such as confounding by cohort effects or non-linear duration patterns. Length of residence in the United States is still an important aspect of Asian immigrant health, but the mechanisms of this relationship are still understudied. I propose alternative frameworks between duration and health that consider environmental influences and end with future research directions to explore research gaps. Full article

Physical and chemical properties of biodiesel are influenced by structural features of the fatty acids, such as chain length, degree of unsaturation and branching of the carbon chain. This study investigated if microalgal fatty acid profiles are suitable for biodiesel characterization and species selection through Preference Ranking Organisation Method for Enrichment Evaluation (PROMETHEE) and Graphical Analysis for Interactive Assistance (GAIA) analysis. Fatty acid methyl ester (FAME) profiles were used to calculate the likely key chemical and physical properties of the biodiesel [cetane number (CN), iodine value (IV), cold filter plugging point, density, kinematic viscosity, higher heating value] of nine microalgal species (this study) and twelve species from the literature, selected for their suitability for cultivation in subtropical climates. An equal-parameter weighted (PROMETHEE-GAIA) ranked Nannochloropsis oculata, Extubocellulus sp. and Biddulphia sp. highest; the only species meeting the EN14214 and ASTM D6751-02 biodiesel standards, except for the double bond limit in the EN14214. Chlorella vulgaris outranked N. oculata when the twelve microalgae were included. Culture growth phase (stationary) and, to a lesser extent, nutrient provision affected CN and IV values of N. oculata due to lower eicosapentaenoic acid (EPA) contents. Application of a polyunsaturated fatty acid (PUFA) weighting to saturation led to a lower ranking of species exceeding the double bond EN14214 thresholds. In summary, CN, IV, C18:3 and double bond limits were the strongest drivers in equal biodiesel parameter-weighted PROMETHEE analysis. Full article

Sun-dried beef is a frequently consumed and valued product in Brazil, however, there have been no scientific studies on its texture. To assess the tenderness of sun-dried beef, an instrumental analysis (Warner-Bratzler Shear Force; WBSF), a sensory analysis (Quantitative Descriptive Analysis; QDA) and the sarcomere length (SL) were used as indicators. Significant differences were observed among the sun-dried beef samples. Sample 3 (composed of sun-dried meat purchased at three fairs from Region 3 in the city of João Pessoa-PB) was considered the most tender by the assessors, with a score of 6.7, and its WBSF analysis revealed a maximum value of 2.70 kgf. Additionally, this sample exhibited the highest SL value (1.89 µm). Samples 1 and 2 (composed of sun-dried meat purchased at three fairs from Regions 1 and 2, respectively, in the city of João Pessoa) exhibited very similar tenderness values (WBSF and QDA) but differed in their SL values, which suggested that sample 2 was the least tender. In conclusion, these results demonstrate that the studied parameters are complementary and can be used as tenderness indicators for sun-dried beef. However, although the difference was beyond the detection limit of the assessors and the texturometer, the SL analysis appears to have been the most effective. Full article

Consumption of fish has well-known human health benefits, though some fish may contain elevated levels of mercury (Hg) that are especially harmful to developing children. Fish length is most often the basis for establishing fishery harvest regulations that determine which fish will ultimately be consumed by humans. It is, therefore, essential to quantify the relationship between fish length and Hg accumulation in regard to harvest regulations for effective fishery and public health policy. We examined this relationship for three sportfish from six lakes across North Carolina, USA. Bluegill (Lepomis macrochirus) had the lowest Hg levels and only the very largest fish in the most contaminated site exceeded the US Environmental Protection Agency (USEPA) Hg screening level. Black crappie (Pomoxis nigromaculatus) had an intermediate level of Hg and larger individuals exceeded the USEPA screening level; however, they tended not to exceed this level before reaching the harvest length limit. Largemouth bass (Micropterus salmoides) exceeded the USEPA screening level at sizes below the fishery length limit in two lakes, leaving only higher risk fish for anglers to harvest and consume. Removing the effects of fish age and trophic position, we found strong positive correlations between Hg and fish length for largemouth bass and black crappie. We suggest public health officials and wildlife managers collaborate to structure fishery regulations and length-based fish consumption advisories that protect consumers from Hg exposure and communicate the relative risk of fish consumption. Full article

The finitely repeated Prisoners’ Dilemma is a good illustration of the discrepancy between the strategic behaviour suggested by a game-theoretic analysis and the behaviour often observed among human players, where cooperation is maintained through most of the game. A game-theoretic reasoning based on backward induction eliminates strategies step by step until defection from the first round is the only remaining choice, reflecting the Nash equilibrium of the game. We investigate the Nash equilibrium solution for two different sets of strategies in an evolutionary context, using replicator-mutation dynamics. The first set consists of conditional cooperators, up to a certain round, while the second set in addition to these contains two strategy types that react differently on the first round action: The ”Convincer” strategies insist with two rounds of initial cooperation, trying to establish more cooperative play in the game, while the ”Follower” strategies, although being first round defectors, have the capability to respond to an invite in the first round. For both of these strategy sets, iterated elimination of strategies shows that the only Nash equilibria are given by defection from the first round. We show that the evolutionary dynamics of the first set is always characterised by a stable fixed point, corresponding to the Nash equilibrium, if the mutation rate is sufficiently small (but still positive). The second strategy set is numerically investigated, and we find that there are regions of parameter space where fixed points become unstable and the dynamics exhibits cycles of different strategy compositions. The results indicate that, even in the limit of very small mutation rate, the replicator-mutation dynamics does not necessarily bring the system with Convincers and Followers to the fixed point corresponding to the Nash equilibrium of the game. We also perform a detailed analysis of how the evolutionary behaviour depends on payoffs, game length, and mutation rate. Full article

An amperometric flow biosensor for oxalate determination in urine samples after enzymatic reaction with oxalate oxidase immobilized on a modified magnetic solid is described. The solid was magnetically retained on the electrode surface of an electrode modified with Fe (III)-tris-(2-thiopyridone) borate placed into a sequential injection system preceding the amperometric detector. The variables involved in the system such as flow rate, aspired volumes (modified magnetic suspension and sample) and reaction coil length were evaluated using a Taguchi parameter design. Under optimal conditions, the calibration curve of oxalate was linear between 3.0–50.0 mg·L⁻¹, with a limit of detection of 1.0 mg·L⁻¹. The repeatability for a 30.0 mg·L⁻¹ oxalate solution was 0.7%. The method was validated by comparing the obtained results to those provided by the spectrophotometric method; no significant differences were observed. Full article

This paper consists of three parts. In the first part, we prove that the Bekenstein-Hawking entropy is the unique expression of black hole entropy. Our proof is constructed in the framework of thermodynamics without any statistical discussion. In the second part, intrinsic properties of quantum mechanics are shown, which justify the Boltzmann formula to yield a unique entropy in statistical mechanics. These properties clarify three conditions, one of which is necessary and others are sufficient for the validity of Boltzmann formula. In the third part, by combining the above results, we find a reasonable suggestion from the sufficient conditions that the potential of gravitational interaction among microstates of underlying quantum gravity may not diverge to negative infinity (such as Newtonian gravity) but is bounded below at a finite length scale. In addition to that, from the necessary condition, the interaction has to be repulsive within the finite length scale. The length scale should be Planck size. Thus, quantum gravity may become repulsive at Planck length. Also, a relation of these suggestions with action integral of gravity at semi-classical level is given. These suggestions about quantum gravity are universal in the sense that they are independent of any existing model of quantum gravity. Full article

A small, highly sensitive, and electromagnetic interference (EMI)-immune refractive index (RI) sensor based on the Fabry-Perot (FP) interferometer is presented. The sensor’s FP cavity was fabricated by aligning two metal-deposited, single-mode optical fiber endfaces inside a microchannel on a silicon chip. The mirrors on the fiber endfaces were made of thermal-deposited metal films, which provided the high finesse necessary to produce a highly sensitive sensor. Microelectromechanical systems (MEMS) fabrication techniques, specifically photolithography and deep dry etching, were used to precisely control the profile and depth of the microchannel on the silicon chip with an accuracy of 2 μm. The RI change within the FP cavity was determined by demodulating the transmission spectrum phase shift. The sensitivity and finesse of the transmission spectrum were controlled by adjusting the cavity length and the thickness of the deposited metal. Our experimental results showed that the sensor’s sensitivity was 665.90 nm/RIU (RI Unit), and the limit of detection was 6 × 10⁻⁶ RIU. Using MEMS fabrication techniques to fabricate these sensors could make high yield mass production a real possibility. Multiple sensors could be integrated on a single small silicon chip to simultaneously measure RI, temperature, and biomolecule targets. Full article

Welding is a major industrial process used for joining metals. Occupational exposure to welding fumes is a serious occupational health problem all over the world. The degree of risk to welder’s health from fumes depends on composition, concentration, and the length of exposure. The aim of this study was to investigate workers’ welding fume exposure levels in some industries in Jeddah, Saudi Arabia. In each factory, the air in the breathing zone within 0.5 m from welders was sampled during 8-hour shifts. Total particulates, manganese, copper, and molybdenum concentrations of welding fumes were determined. Mean values of eight-hour average particulate concentrations measured during welding at the welders breathing zone were 6.3 mg/m³ (Factory 1), 5.3 mg/m³ (Factory 2), 11.3 mg/m³ (Factory 3), 6.8 mg/m³ (Factory 4), 4.7 mg/m³ (Factory 5), and 3.0 mg/m³ (Factory 6). Mean values of airborne manganese, copper, and molybdenum levels measured during welding were in the range of 0.010 mg/m³–0.477 mg/m³, 0.001 mg/m³–0.080 mg/m³ and 0.001 mg/m³–0.058 mg/m³ respectively. Mean values of calculated equivalent exposure values were: 1.50 (Factory 1), 1.56 (Factory 2), 5.14 (Factory 3), 2.21 (Factory 4), 2.89 (Factory 5), and 1.20 (Factory 6). The welders in factories 1, 2, 3, and 4 were exposed to welding fume concentration above the SASO limit value, which may increase the risk of respiratory health problems. Full article

High specific surface area (SSA_BET: 141.6 m²/g) SnO₂ nanoparticles doped with 0.2–3 wt% Ru were successfully produced in a single step by flame spray pyrolysis (FSP). The phase and crystallite size were analyzed by XRD. The specific surface area (SSA_BET) of the nanoparticles was measured by nitrogen adsorption (BET analysis). As the Ru concentration increased, the SSA_BET was found to linearly decrease, while the average BET-equivalent particle diameter (d_BET) increased. FSP yielded small Ru particles attached to the surface of the supporting SnO₂ nanoparticles, indicating a high SSA_BET. The morphology and accurate size of the primary particles were further investigated by TEM. The crystallite sizes of the spherical, hexagonal, and rectangular SnO₂ particles were in the range of 3–10 nm. SnO₂ nanorods were found to range from 3–5 nm in width and 5–20 nm in length. Sensing films were prepared by the spin coating technique. The gas sensing of H₂ (500–10,000 ppm) was studied at the operating temperatures ranging from 200–350 °C in presence of dry air. After the sensing tests, the morphology and the cross-section of sensing film were analyzed by SEM and EDS analyses. The 0.2%Ru-dispersed on SnO₂ sensing film showed the highest sensitivity and a very fast response time (6 s) compared to a pure SnO₂ sensing film, with a highest H₂ concentration of 1 vol% at 350 °C and a low H₂ detection limit of 500 ppm at 200 °C. Full article

In this work, methane detection is performed on the 2ν₃ and ν₂ + 2ν₃ absorption bands in the Near-Infrared (NIR) wavelength region using an all-fibre optical sensor. Hollowcore photonic bandgap fibres (HC-PBFs) are employed as gas cells due to their compactness, good integrability in optical systems and feasibility of long interaction lengths with gases. Sensing in the 2ν₃ band of methane is demonstrated to achieve a detection limit one order of magnitude better than that of the ν₂ + 2ν₃ band. Finally, the filling time of a HC-PBF is demonstrated to be dependent on the fibre length and geometry. Full article

The spatial resolution of a conventional imaging lidar system is constrained by the diffraction limit of the telescope’s aperture. The combination of the lidar and synthetic aperture (SA) processing techniques may overcome the diffraction limit and pave the way for a higher resolution air borne or space borne remote sensor. Regarding the lidar transmitting frequency modulation continuous-wave (FMCW) signal, the motion during the transmission of a sweep and the reception of the corresponding echo were expected to be one of the major problems. The given modified Omega-K algorithm takes the continuous motion into account, which can compensate for the Doppler shift induced by the continuous motion efficiently and azimuth ambiguity for the low pulse recurrence frequency limited by the tunable laser. And then, simulation of Phase Screen (PS) distorted by atmospheric turbulence following the von Karman spectrum by using Fourier Transform is implemented in order to simulate turbulence. Finally, the computer simulation shows the validity of the modified algorithm and if in the turbulence the synthetic aperture length does not exceed the similar coherence length of the atmosphere for SAIL, we can ignore the effect of the turbulence. Full article

Lactoferrin is a multifunctional protein with antimicrobial activity and others tohealth beneficial properties. The main aim of this work was to propose easy to usetechnique for lactoferrin isolation from cow colostrum samples. Primarily we utilizedsodium dodecyl sulphate – polyacrylamide gel electrophoresis for isolation of lactoferrinfrom the real samples. Moreover we tested automated microfluidic Experionelectrophoresis system to isolate lactoferrin from the collostrum sample. The welldeveloped signal of lactoferrin was determined with detection limit (3 S/N) of 20 ng/ml. Inspite of the fact that Experion is faster than SDS-PAGE both separation techniques cannotbe used in routine analysis. Therefore we have tested third separation technique, ionexchange chromatography, using monolithic column coupled with UV-VIS detector (LCUV-VIS). We optimized wave length (280 nm), ionic strength of the elution solution (1.5M NaCl) and flow rate of the retention and elution solutions (0.25 ml/min and 0.75 ml/min.respectively). Under the optimal conditions the detection limit was estimated as 0.1 μg/mlof lactoferrin measured. Using LC-UV-VIS we determined that lactoferrin concentrationvaried from 0.5 g/l to 1.1 g/l in cow colostrums collected in the certain time interval up to 72 hours after birth. Further we focused on miniaturization of detection device. We testedamperometric detection at carbon electrode. The results encouraged us to attempt tominiaturise whole detection system and to test it on analysis of real samples of humanfaeces, because lactoferrin level in faeces is closely associated with the inflammations ofintestine mucous membrane. For the purpose of miniaturization we employed thetechnology of printed electrodes. The detection limit of lactoferrin was estimated as 10μg/ml measured by the screen-printed electrodes fabricated by us. The fabricatedelectrodes were compared with commercially available ones. It follows from the obtainedresults that the responses measured by commercial electrodes are app. ten times highercompared with those measured by the electrodes fabricated by us. This phenomenonrelates with smaller working electrode surface area of the electrodes fabricated by us(about 50 %) compared to the commercial ones. The screen-printed electrodes fabricatedby us were utilized for determination of lactoferrin faeces. Regarding to fact that sample offaeces was obtained from young and healthy man the amount of lactoferrin in sample wasunder the limit of detection of this method. Full article

Based on theoretical modeling and optimization, we exploit the application ofoptical microfiber loop resonators in ambient refractive index sensing. We set up a reliabletheoretical model and optimize the structural parameters of microfiber loop resonatorsincluding the radius of the microrfiber, the radius of the loop and the length of the couplingregion for higher sensitivity, wider dynamic measurement range, and lower detection limit.To show the convincible and realizable sensing ability we perform the simulation ofsensing an extreme small variation of ambient refractive index by employing a set ofexperimental data as the parameters in the expression of intensity transmission coefficient,and the detection limit reaches to a variation of ambient refractive index of 10^-5 refractiveindex unit (RIU). This has superiority over the existing evanescent field-basedsubwavelength-diameter optical fiber refractive index sensor. Full article