Creep tests of the polycrystalline nickel alloy Waspaloy have been conducted at Swansea University, for varying stress conditions at 700 °C. Investigation through use of Transmission Electron Microscopy at Cambridge University has examined the dislocation networks formed under these conditions, with particular attention paid to comparing tests performed above and below the yield stress. This paper highlights how the dislocation structures vary throughout creep and proposes a dislocation mechanism theory for creep in Waspaloy. Activation energies are calculated through approaches developed in the use of the recently formulated Wilshire Equations, and are found to differ above and below the yield stress. Low activation energies are found to be related to dislocation interaction with γ′ precipitates below the yield stress. However, significantly increased dislocation densities at stresses above yield cause an increase in the activation energy values as forest hardening becomes the primary mechanism controlling dislocation movement. It is proposed that the activation energy change is related to the stress increment provided by work hardening, as can be observed from Ti, Ni and steel results. Full article

Non-isothermal conditions during flight cycles have long led to the requirement for thermo-mechanical fatigue (TMF) evaluation of aerospace materials. However, the increased temperatures within the gas turbine engine have meant that the requirements for TMF testing now extend to disc alloys along with blade materials. As such, fatigue crack growth rates are required to be evaluated under non-isothermal conditions along with the development of a detailed understanding of related failure mechanisms. In the current work, a TMF crack growth testing method has been developed utilising induction heating and direct current potential drop techniques for polycrystalline nickel-based superalloys, such as RR1000. Results have shown that in-phase (IP) testing produces accelerated crack growth rates compared with out-of-phase (OOP) due to increased temperature at peak stress and therefore increased time dependent crack growth. The ordering of the crack growth rates is supported by detailed fractographic analysis which shows intergranular crack growth in IP test specimens, and transgranular crack growth in 90° OOP and 180° OOP tests. Isothermal tests have also been carried out for comparison of crack growth rates at the point of peak stress in the TMF cycles. Full article

Magnetic resonance spectroscopy (MRS) is a non-invasive method for quantitative estimation of liver fat. Knowledge of its imprecision, which comprises biological variability and measurement error, is required to design therapeutic trials with measurement of change. The role of adipocyte lipolysis in ectopic fat accumulation remains unclear. We examined the relationship between liver fat content and indices of lipolysis, and determine whether lipolysis reflects insulin resistance or metabolic liver disease. Imprecision of measurement of liver fat was estimated from duplicate measurements by MRS at one month intervals. Patients provided fasting blood samples and we examined the correlation of liver fat with indices of insulin resistance, lipolysis and metabolic liver disease using Kendall Tau statistics. The coefficient of variation of liver fat content was 14.8%. Liver fat was positively related to serum insulin (T = 0.48, p = 0.042), homeostasis model assessment (HOMA)-B% (T = −0.48, p = 0.042), and body mass index (BMI) (T = 0.59, p = 0.012); and inversely related to HOMA-S% (T = −0.48, p = 0.042), serum glycerol (T = −0.59, p = 0.014), and serum caeruloplasmin (T = 0.055, p = 0.047). Our estimate of total variability in liver fat content (14.8%) is nearly twice that of the reported procedural variability (8.5%). We found that liver fat content was significantly inversely related to serum glycerol but not to non-esterified fatty acids (NEFA), suggesting progressive suppression of lipolysis. Reduction of caeruloplasmin with increasing liver fat may be a consequence or a cause of hepatic steatosis. Full article

Imaging technologies that allow the non-invasive monitoring of stem cells in vivo play a vital role in cell-based regenerative therapies. Recently, much interest has been generated in reporter genes that enable simultaneous monitoring of the anatomical location and viability of cells using magnetic resonance imaging (MRI). Here, we investigate the efficacy of ferritin heavy chain-1 (Fth1) and transferrin receptor-1 (TfR1) as reporters for tracking mesenchymal stem cells. The overexpression of TfR1 was well tolerated by the cells but Fth1 was found to affect the cell’s iron homeostasis, leading to phenotypic changes in the absence of iron supplementation and an upregulation in transcript and protein levels of the cell’s endogenous transferrin receptor. Neither the sole overexpression of Fth1 nor TfR1 resulted in significant increases in intracellular iron content, although significant differences were seen when the two reporter genes were used in combination, in the presence of high concentrations of iron. The supplementation of the culture medium with iron sources was a more efficient means to obtain contrast than the use of reporter genes, where high levels of intracellular iron were reflected in transverse (T₂) relaxation. The feasibility of imaging iron-supplemented cells by MRI is shown using a 3R-compliant chick embryo model. Full article

Recent work in the creep field has indicated that the traditional methodologies involving power law equations are not sufficient to describe wide ranging creep behaviour. More recent approaches such as the Wilshire equations however, have shown promise in a wide range of materials, particularly in extrapolation of short term results to long term predictions. In the aerospace industry however, long term creep behaviour is not critical and more focus is required on the prediction of times to specific creep strains. The current paper illustrates the capability of the Wilshire equations to recreate full creep curves in a modern nickel superalloy. Furthermore, a finite-element model based on this method has been shown to accurately predict stress relaxation behaviour allowing more accurate component lifing. Full article