Flame Retardant Coatings for Plastics and Textiles

A special issue of Coatings (ISSN 2079-6412).

Deadline for manuscript submissions: closed (31 January 2022) | Viewed by 30394

Special Issue Editors

Department of Materials Engineering, Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic
Interests: diagnostic of solid materials; polymers

Special Issue Information

Dear Colleagues,

This Special Issue will focus on the recent advances and emerging challenges in the field of flame retardancy achieved by applying coatings to such substrates as plastics (including polymer composites) and textiles. This is an up-to-date topic that deserves investigation both from an academic and industrial point of view, also considering the current restrictions on the use of flame retardants according to the recent European directives.

In particular, the topic of interest includes but is not limited to

  • Hybrid O/I fire retardant coatings
  • Intumescent fire retardant coatings
  • Fire retardant coatings with multifunctional features
  • Toxicity and environmental issues related to the use of fire retardant coatings

Prof. Dr. Giulio Malucelli
Prof. Dr. Pavel Koštial
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Coatings is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Published Papers (10 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Editorial

Jump to: Research, Review

2 pages, 174 KiB  
Editorial
How to Reduce the Flammability of Plastics and Textiles through Surface Treatments: Recent Advances
by Giulio Malucelli
Coatings 2022, 12(10), 1563; https://doi.org/10.3390/coatings12101563 - 17 Oct 2022
Viewed by 988
Abstract
The high flammability of plastics, polymer composites, textiles, and foams represents a severe and stringent issue that significantly limits their use in all those sectors, where resistance to a flame or an irradiative heat flux is mandatory [...] Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)

Research

Jump to: Editorial, Review

13 pages, 2684 KiB  
Article
Development of Multifunctional Flame-Retardant Gel Coatings for Automotive Applications
by Zsófia Kovács, Ákos Pomázi and Andrea Toldy
Coatings 2023, 13(2), 345; https://doi.org/10.3390/coatings13020345 - 02 Feb 2023
Cited by 3 | Viewed by 1702
Abstract
Due to strict safety regulations, the automotive industry requires an effective reduction of flammability in polymer components. Flame retardants are usually added to the polymer matrix, affecting the viscosity of the matrix. Another possible solution is the application of coatings containing flame retardants, [...] Read more.
Due to strict safety regulations, the automotive industry requires an effective reduction of flammability in polymer components. Flame retardants are usually added to the polymer matrix, affecting the viscosity of the matrix. Another possible solution is the application of coatings containing flame retardants, which can additionally ensure good surface quality and protection against external influences. In our research, the flammability of reference and flame retarded gelcoat base materials was investigated using oxygen index (LOI), UL-94, and mass loss type cone calorimetry (MLC) tests. Based on the flammability tests, the best results were obtained with the gelcoat formulation containing 15%P ammonium polyphosphate (APP) and the mixed formulation containing 5%P APP and 5%P resorcinol bis(diphenyl phosphate) (RDP), with a 55% and 64% reduction in the total heat release compared to the reference gelcoat, respectively. The two best-performing coatings were applied to polypropylene (PP) samples. 15%P APP reduced the peak heat release rate of PP by 89% compared to the reference. The gelcoat formulation containing 15%P APP was applied to polyurethane (PUR) automotive components, where the coating reduced the maximum heat release rate by 53% and shifted the time to peak heat release rate by 447 s. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Graphical abstract

18 pages, 7851 KiB  
Article
New Transparent Flame-Retardant (FR) Coatings Based on Epoxy-Aluminum Hypophosphite Nanocomposites
by Fouad Laoutid, Maryam Jouyandeh, Oltea Murariu, Henri Vahabi, Mohammad Reza Saeb, Loic Brison, Marius Murariu and Philippe Dubois
Coatings 2023, 13(1), 140; https://doi.org/10.3390/coatings13010140 - 10 Jan 2023
Cited by 6 | Viewed by 1836
Abstract
The present study investigated the flame-retardant (FR) effect of transparent epoxy coating containing aluminum hypophosphite (AHP) nanoparticles (NPs) on polylactic acid (PLA) sheets used as a typical model of combustible polymeric material. First, AHP NPs (≤60 nm) were prepared by a specific two-stage [...] Read more.
The present study investigated the flame-retardant (FR) effect of transparent epoxy coating containing aluminum hypophosphite (AHP) nanoparticles (NPs) on polylactic acid (PLA) sheets used as a typical model of combustible polymeric material. First, AHP NPs (≤60 nm) were prepared by a specific two-stage wet milling process and deeply analyzed (morphology, thermal/mechanisms of degradation under nitrogen and air). The thermal properties of epoxy–AHP nanocomposites were compared with the pristine epoxy resin. The addition of AHP NPs into epoxy resin accelerated thermal degradation of the coating, thereby increasing the amount of char residue. The application of blank epoxy coating on the surface of PLA plate slightly made PLA more ignitable, without any reduction in the peak of heat release rate (pHRR). The decrease of time to ignition (TTI) was more important in the presence of AHP NPs due to their reactivity toward epoxy resin. Epoxy coating containing 15 wt.% AHP NPs showed the most significant reduction in pHRR as the result of the formation of a homogenous char layer. Further increase of AHP NPs content up to 20 wt.% did not end in any further enhancement, as a consequence of structural cracks observed in the coating that prevent the formation of an effective char. The coated samples remained transparent, promisingly paving the way to appropriate decorative flame-retardant coatings. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

13 pages, 2152 KiB  
Article
Design and Performance Evaluation of Flame Retardant and Thermally Insulated Material-Integrated Multi-Functional Thermoplastic Corrugated Sandwich Panels
by Yiliang Sun, Jingwen Li, Boming Zhang, Yixuan Song and Hongfu Li
Coatings 2022, 12(11), 1719; https://doi.org/10.3390/coatings12111719 - 10 Nov 2022
Cited by 1 | Viewed by 1002
Abstract
Multifunctional composite panels for flame retardant and thermal insulation have not yet been studied. In the current study, we prepared sandwich sheets by using continuous glass fiber flame retardant polypropylene prepreg tape and compared the thermal insulation properties of different fillings. Corrugated sandwich [...] Read more.
Multifunctional composite panels for flame retardant and thermal insulation have not yet been studied. In the current study, we prepared sandwich sheets by using continuous glass fiber flame retardant polypropylene prepreg tape and compared the thermal insulation properties of different fillings. Corrugated sandwich panels, featuring a corrugated space filled with different materials, were prepared and their thermal and mechanical properties are tested and verified. Determining the two structural parameters that have the greatest influence on the heat transfer performance of corrugated sandwich panels has important guiding significance for the structural design of corrugated panels. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

14 pages, 4209 KiB  
Article
Flame Retardancy Performance of Continuous Glass-Fiber-Reinforced Polypropylene Halogen-Free Flame-Retardant Prepreg
by Yiliang Sun, Jingwen Li and Hongfu Li
Coatings 2022, 12(7), 976; https://doi.org/10.3390/coatings12070976 - 09 Jul 2022
Cited by 1 | Viewed by 2298
Abstract
Thermoplastic resin matrix has a high melt viscosity, which is difficult to impregnate with fibers. The addition of flame retardant will further increase the viscosity of the melt and increase the difficulty of impregnation. It is possible to reduce the effect of flame [...] Read more.
Thermoplastic resin matrix has a high melt viscosity, which is difficult to impregnate with fibers. The addition of flame retardant will further increase the viscosity of the melt and increase the difficulty of impregnation. It is possible to reduce the effect of flame retardant on melt viscosity by adding high-flow polypropylene. In this study, the effect of adding flame retardant on the impregnation quality of prepreg tape was investigated. By adding high-flow polypropylene to improve the melt viscosity of flame-retardant-modified polypropylene, continuous glass-fiber-reinforced polypropylene flame-retardant prepreg tape was successfully prepared. Intumescent flame retardant (IFR) was added at 20 wt%, 25 wt%, 30 wt% of the polypropylene matrixes, which were prepared by melt impregnation. The composites were analyzed with thermogravimetric analysis, limiting oxygen index testing, UL-94 flame retardancy testing, cone calorimeter testing (CCT) and scanning electron microscopy. Tests involving the flame retardant showed that when the added amount of flame retardant reached 25%, the UL-94 flame retardancy grade reached V0. Compared with the CCT sample heating data, taking economic considerations into account, 25 wt% IFR addition was the most suitable. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

13 pages, 5445 KiB  
Article
Case Study on Fire Resistance of Sandwiches for Means of Transport
by Pavel Koštial, Zora Koštialová Jančíková and Robert Frischer
Coatings 2021, 11(2), 207; https://doi.org/10.3390/coatings11020207 - 11 Feb 2021
Cited by 5 | Viewed by 1743
Abstract
These days there are undeniably unique materials that, however, must also meet demanding safety requirements. In the case of vehicles, these are undoubtedly excellent fire protection characteristics. The aim of the work is to experimentally verify the proposed material compositions for long-term heat [...] Read more.
These days there are undeniably unique materials that, however, must also meet demanding safety requirements. In the case of vehicles, these are undoubtedly excellent fire protection characteristics. The aim of the work is to experimentally verify the proposed material compositions for long-term heat loads and the effect of thickness, the number of laminating layers (prepregs) as well as structures with different types of cores (primarily honeycomb made of Nomex paper type T722 of different densities, aluminum honeycomb and PET foam) and composite coating based on a glass-reinforced phenolic matrix. The selected materials are suitable candidates for intelligent sandwich structures, usable especially for interior cladding applications in the industry for the production of means of public transport (e.g., train units, trams, buses, hybrid vehicles). Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

17 pages, 6046 KiB  
Article
Influence of Magnesium Aluminate Nanoparticles on Epoxy-Based Intumescent Flame Retardation Coating System
by Hatem Abuhimd, Tentu Nageswara Rao, Jung-il Song, Prashanthi Yarasani, Faheem Ahmed, Botsa Parvatamma, Asma A. Alothman, Murefah Mana AL-Anazy and Ahmad A. Ifseisi
Coatings 2020, 10(10), 968; https://doi.org/10.3390/coatings10100968 - 12 Oct 2020
Cited by 7 | Viewed by 2297
Abstract
Ethylenediamine modified ammonium polyphosphate (EDA-MAPP) and charring-foaming agents (CFA) were prepared using a simple chemical method and further used to make intumescent flame retardant coatings based on epoxy resin. The content of MAPP and CFA was fixed at a ratio of 2:1. Nanoparticles [...] Read more.
Ethylenediamine modified ammonium polyphosphate (EDA-MAPP) and charring-foaming agents (CFA) were prepared using a simple chemical method and further used to make intumescent flame retardant coatings based on epoxy resin. The content of MAPP and CFA was fixed at a ratio of 2:1. Nanoparticles of magnesium aluminate (MgAl2O4 NPs) have been introduced into the flame retardant coating formulation in various quantities to evaluate the promotional action of MgAl2O4 NPs with a flame retardant coating system. The promotional action of MgAl2O4 NPs on the flame retardant coating formulation was studied using a vertical burning test (UL-94V), limiting oxygen index (LOI), thermogravimetric analysis (TGA) and Fourier transform infra-red spectroscopy (FTIR). The UL-94V results indicated that the addition of MgAl2O4 effectively increased flame retardancy and met the V-0 rating at each concentration. The TGA results revealed that the incorporation of MgAl2O4 NPs at each concentration effectively increased the thermal stability of the flame retardant coating system. Cone-calorimeter experiments show that MgAl2O4 NPs effectively decreased peak heat release rate (PHRR) and total heat release (THR). The FTIR results indicated that MgAl2O4 NPs can react with MAPP and generate a dense char layer that prevents the transfer of oxygen and heat. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

20 pages, 4112 KiB  
Article
Improved Thermal Processing of Polylactic Acid/Oxidized Starch Composites and Flame-Retardant Behavior of Intumescent Non-Wovens
by Muhammad Maqsood and Gunnar Seide
Coatings 2020, 10(3), 291; https://doi.org/10.3390/coatings10030291 - 20 Mar 2020
Cited by 10 | Viewed by 3434
Abstract
Thermoplastic processing and spinning of native starch is very challenging due to (a) the linear and branched polymers (amylose and amylopectin) present in its structure and (b) the presence of inter-and-intramolecular hydrogen bond linkages in its macromolecules that restrict the molecular chain mobility. [...] Read more.
Thermoplastic processing and spinning of native starch is very challenging due to (a) the linear and branched polymers (amylose and amylopectin) present in its structure and (b) the presence of inter-and-intramolecular hydrogen bond linkages in its macromolecules that restrict the molecular chain mobility. Therefore, in this study, oxidized starch (OS) (obtained after oxidation of native starch with sodium perborate) was melt-blended with polylactic acid (PLA) polymer to prepare PLA/OS blends that were then mixed together with ammonium polyphosphate (APP), a halogen-free flame retardant (FR) used as acid donor in intumescent formulations on twin-screw extruder to prepare PLA/OS/APP composites. OS with different concentrations also served as bio-based carbonic source in intumescent formulations. PLA/OS/APP composites were melt spun to multifilament fibers on pilot scale melt-spinning machine and their crystallinity and mechanical properties were optimized by varying spinning parameters. The crystallinity of the fibers was studied by differential scanning calorimetry and thermal stabilities were analyzed by thermogravimetric analysis. Scanning electron microscopy was used to investigate the surface morphology and dispersion of the additives in the fibers. Needle-punched non-woven fabrics from as prepared melt-spun PLA/OS/APP fibers were developed and their fire properties such as heat release rate, total heat release, time to ignition, residual mass % etc. by cone calorimetry test were measured. It was found that PLA/OS/APP composites can be melt spun to multifilament fibers and non-woven flame-retardant fabrics produced thereof can be used in industrial FR applications. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

Review

Jump to: Editorial, Research

18 pages, 955 KiB  
Review
Sol-Gel and Layer-by-Layer Coatings for Flame-Retardant Cotton Fabrics: Recent Advances
by Giulio Malucelli
Coatings 2020, 10(4), 333; https://doi.org/10.3390/coatings10040333 - 01 Apr 2020
Cited by 31 | Viewed by 4842
Abstract
Surface-engineered coatings for the fire protection of cotton are being increasing used thanks to the ease of application of the coatings and their effectiveness in preventing flame propagation and improving resistance to irradiative heat flux exposure. Two main approaches have been extensively investigated, [...] Read more.
Surface-engineered coatings for the fire protection of cotton are being increasing used thanks to the ease of application of the coatings and their effectiveness in preventing flame propagation and improving resistance to irradiative heat flux exposure. Two main approaches have been extensively investigated, namely sol-gel derived coatings and layer-by-layer assemblies. These approaches are both capable of providing treated fabrics with outstanding flame-retardant features. Notwithstanding, according to the composition of the sol-gel recipes and the type of deposited layers, it is possible to design multifunctional (for example hydrophobic and electrically conductive) treatments. This review aims at discussing recent advances with respect to both strategies, highlighting current limitations, open challenges, and possible advances. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Figure 1

23 pages, 6622 KiB  
Review
Multifunctional Gelcoats for Fiber Reinforced Composites
by Ákos Pomázi and Andrea Toldy
Coatings 2019, 9(3), 173; https://doi.org/10.3390/coatings9030173 - 06 Mar 2019
Cited by 23 | Viewed by 6719
Abstract
Achieving special features in polymer composites, such as flame retardancy and thermal and electrical conductivity, often requires the application of different additives, which might negatively affect other properties of the polymer matrix and the composite structure. Furthermore, the application of solid additives in [...] Read more.
Achieving special features in polymer composites, such as flame retardancy and thermal and electrical conductivity, often requires the application of different additives, which might negatively affect other properties of the polymer matrix and the composite structure. Furthermore, the application of solid additives in composites produced by liquid transfer moulding can lead to the filtration of the additive by the reinforcement, which causes a non-uniform particle distribution and an uneven performance. An evident solution to address these issues is to apply the additives in a separate layer on the surface of the composite. As in many applications, gelcoats are used to reach appropriate surface quality, a reasonable progression in the composite industry is the development of multifunctional gelcoats. In this article, after a short introduction to gelcoats and their main base materials (unsaturated polyester, epoxy, and others) multifunctional gelcoats are discussed according to their functionality, in particular water resistance, electric conductivity and flame retardancy. Classical and novel gelcoat preparation methods (application by brush and/or roller, spraying, UV-curing, in-mould gelcoating), as well as common defects that occur during gelcoating are discussed. Finally, the testing methods of multifunctional gelcoats are outlined. Full article
(This article belongs to the Special Issue Flame Retardant Coatings for Plastics and Textiles)
Show Figures

Graphical abstract

Back to TopTop