Next Article in Journal
Investigation of Material Performance Degradation for High-Strength Aluminum Alloy Using Acoustic Emission Method
Next Article in Special Issue
Effect of Indium Content on the Microstructure, Mechanical Properties and Corrosion Behavior of Titanium Alloys
Previous Article in Journal
Nanocrystalline Ti Produced by Cryomilling and Consolidation by Severe Plastic Deformation
Previous Article in Special Issue
Titanium Matrix Composite Ti/TiN Produced by Diode Laser Gas Nitriding
Article Menu

Export Article

Open AccessArticle
Metals 2015, 5(1), 216-227; doi:10.3390/met5010216

Hot Deformation Behavior of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe Alloy in α + β Field

1
School of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot 010051, China
2
National Key Laboratory of Science and Technology on Precision Heat Processing of Metals, Harbin Institute of Technology, Harbin 150001, China
*
Author to whom correspondence should be addressed.
Academic Editor: M. T. Whittaker
Received: 10 January 2015 / Revised: 22 January 2015 / Accepted: 3 February 2015 / Published: 13 February 2015
(This article belongs to the Special Issue Titanium Alloys)
View Full-Text   |   Download PDF [1637 KB, uploaded 13 February 2015]   |  

Abstract

The deformation behavior of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe high strength β titanium alloy is systematically investigated by isothermal compression in α + β field with the deformation temperatures ranging from 1003 K to 1078 K, the strain rates ranging from 0.001 s−1 to 1 s−1 and the height reduction is around 50%. Essentially, the flow stress-strain curve of isothermal compression in α + β field exhibits a flow softening feature when the strain rate is higher than 0.1 s−1 as while it exhibits a steady-state feature as the strain rate is lower than 0.1 s−1. The peak stress increases with a decrease in deformation temperature and the increase of strain rate. The activation energy for deformation in α + β field was calculated and the average activation energy of 271.1 kJ/mol. The microstructure observation reveals that the isothermal deformation in the α + β field of the alloy is mainly controlled by the dynamic recovery mechanism accompanied with the secondary dynamic recrystallizitation of β phase. The α phase shows an obvious pinning effect for the movement of dislocations. During deformation, the α phase was elongated and fragmented. View Full-Text
Keywords: β titanium alloys; activation energy; microstructure evolution; deformation mechanism β titanium alloys; activation energy; microstructure evolution; deformation mechanism
This is an open access article distributed under the Creative Commons Attribution License which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. (CC BY 4.0).

Scifeed alert for new publications

Never miss any articles matching your research from any publisher
  • Get alerts for new papers matching your research
  • Find out the new papers from selected authors
  • Updated daily for 49'000+ journals and 6000+ publishers
  • Define your Scifeed now

SciFeed Share & Cite This Article

MDPI and ACS Style

Du, Z.; Xiao, S.; Liu, J.; Lv, S.; Xu, L.; Kong, F.; Chen, Y. Hot Deformation Behavior of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe Alloy in α + β Field. Metals 2015, 5, 216-227.

Show more citation formats Show less citations formats

Related Articles

Article Metrics

Article Access Statistics

1

Comments

[Return to top]
Metals EISSN 2075-4701 Published by MDPI AG, Basel, Switzerland RSS E-Mail Table of Contents Alert
Back to Top