Next Article in Journal
Dynamic Modeling and Real-Time Monitoring of Froth Flotation
Next Article in Special Issue
Fault Reactivation Can Generate Hydraulic Short Circuits in Underground Coal Gasification—New Insights from Regional-Scale Thermo-Mechanical 3D Modeling
Previous Article in Journal
An Underground Air-Route Temperature Prediction Model for Ultra-Deep Coal Mines
Previous Article in Special Issue
Market Structure Differences Impacting Australian Iron Ore and Metallurgical Coal Industries
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

RTRO–Coal: Real-Time Resource-Reconciliation and Optimization for Exploitation of Coal Deposits

1
Section Resource Engineering, Faculty of Civil Technique and Geosciences, Department of Geoscience and Engineering, Delft University of Technology, Stevinweg 1, 2628 CN Delft, The Netherlands
2
RWE Power AG, Stüttgenweg 2, 50935 Köln, Germany
3
Mitteldeutsche Braunkohlengesellschaft mbH, Glück-Auf-Straße 1, 06711 Zeitz, Germany
4
Institute for Mine Surveying and Geodesy, Faculty of Geosciences, Geoengineering and Mining, University of Technology Bergakademie Freiberg, Reiche Zeche, Fuchsmühlenweg 9, 09599 Freiberg, Germany
5
Faculty of Mining and Geoengineering, AGH University of Science and Technology, aleja Adama Mickiewicza 30, 30-059 Kraków, Poland
*
Author to whom correspondence should be addressed.
Minerals 2015, 5(3), 546-569; https://doi.org/10.3390/min5030509
Submission received: 30 June 2015 / Revised: 12 August 2015 / Accepted: 17 August 2015 / Published: 25 August 2015

Abstract

:
This contribution presents an innovative and integrated framework for real-time-process reconciliation and optimization (RTRO) in large continuous open pit coal mines. RTRO-Coal is currently developed, validated, tested and implemented as part of a multi-national multi-partner European Union funded R&D project. The key concept is to promote a shift in paradigm from intermittent discontinuous to a continuous process monitoring and quality management system in large scale coal mining operations. The framework is based on a real-time feedback control loop linking online data acquired during extraction rapidly with a sequentially up-datable resource model. The up-to-date model is integrated with a real-time optimization of short-term sequencing and production control decisions. Improved decisions are expected to lead to increased resource-and process efficiency and support a sustainable extraction of natural resources. This contribution introduces to the framework, discusses main building blocks and illustrates the value added by the means of selected examples.

1. Moving Towards Real-Time Project Control in the Exploitation of Coal Deposits

A sustainable exploitation of coal deposits is a complex multi-objective task. On the one hand, the coal extracted from deposits has to meet tight customer specifications; mainly modern coal fired power plants. On the other hand, coal deposits can be rather complex and often involve multiple seams with multiple splits and diverse inherent coal-quality distributions. Customer requirements are usually in terms of upper and lower bounds of multiple coal quality parameters, such as calorific value, ash or sulphur, which have to be met on a train by train basis. The overburden covering the coal has to be excavated, transported and dumped in a sequence that guarantees safety and long-term stability of the waste dump. At the same time production management aims to maximize utilization and effective production rates of major mining equipment, minimize specific costs and contribute to the long-term mine plan.
Successful planning and operations management in coal extraction have to be based on a sound understanding of key features in the deposit. This knowledge is usually based on exploration data and typically captured in a digital 3D resource model. Exploration data are gathered in campaigns prior to operation, often undertaken years or decades ago. The sample spacing is designed to capture major features of the deposit with the anticipated level of accuracy, while there is often the mandate to reduce exploration expenditure. Although resource models are created using sophisticated geostatistical modelling techniques, such as different types of Kriging or conditional simulation, locally they can exhibit significant deviations from in-situ resource characteristics [1]. Short-term production scheduling is based on resource models and aims to define an extraction sequence that is aligned with the previously mentioned objectives. The scale of short-term production targets can be as small as a train load in the order of 1000 t that is shipped to a power plant; such a scale is not supported by data gathered during exploration. Consequences can be unexpected deviations from production targets, which may have significant impacts on sustainable process indicators. Therefore the understanding of short scale variability of coal characteristics is critical in order to control the operation and to meet production targets with a high level of reliability.
With recent developments in production monitoring over the past decade, online data capturing production performance provide an enormous alternative source of information. Literally a flood of data is available, captured in a high spatial and timely resolution. Sensor technology for detecting characteristics of raw materials on a conveyor belt has been proven in industrial applications in some mining operations. For example, Figure 1 shows a radiometric sensor on a coal-conveyor measuring ash-content online. Figure 2 compares laboratory analyses and sensor based measurements for coal ash content of train-car loads of approximately 100 t. The correlation coefficient of 0.93 suggests a high information content of sensor data. A second example is GPS data of equipment, measuring the exact extraction location. Implementations of such kind of systems are standard in continuous lignite mining. Examples are the RWE Power system “satellite-assisted excavator operation control-SABAS” [2] or online reconstructions of actual excavator cutting plains by MIBRAG [3]. Figure 3 illustrates results of such measurements, which provide direct information about actual excavated coal-waste boundaries.
Figure 1. Radiometric sensor measurement of coal in the Profen mine (photo of MIBRAG).
Figure 1. Radiometric sensor measurement of coal in the Profen mine (photo of MIBRAG).
Minerals 05 00509 g001
Figure 2. Correlation between sensor-based measurements and lab analysis in coal samples.
Figure 2. Correlation between sensor-based measurements and lab analysis in coal samples.
Minerals 05 00509 g002
To date, sensor information are mainly utilized in feed forward loops applied for downstream process control, such as supporting dispatch decisions, material sorting or blending on stockpiles [4,5,6]. An immediate feedback of sensor information into the resource model and planning assumptions to continuously increase its certainty in prediction does not occur. Reconciliation exercises are often performed on a discontinuous basis and over a monthly to a yearly time span. However, the ability to immediately feedback production monitoring data suggests a significant potential for improvement an operational efficiency. With increased certainty of prediction of coal qualities or material characteristics of overburden blocks the frequency of misclassification and unfavorable dispatch decisions is expected to decrease. Buxton and Benndorf [7] quantified this value in the order of $5 Mio. per annum for an average sized operation.
Figure 3. Online GPS-data of an excavator digging a coal seam (reproduced after [3]).
Figure 3. Online GPS-data of an excavator digging a coal seam (reproduced after [3]).
Minerals 05 00509 g003
RTRO-Coal is a multi-partner European funded project, which aims to lift the previously mentioned potential. The abbreviation RTRO-Coal stands for Real-Time-Reconciliation and Optimization of the production process in large open pit coal mining operations. The framework links new methods in continuous mine system simulation, intelligent data analysis, advanced geological modelling and process optimization. Relevant data and information, captured online along the production process, are integrated in a near real-time manner to ensure efficient production of within-specification coal products.
The aim of this contribution is first to introduce the overall RTRO-Coal concept and its main building blocks. Subsequently, the state-of-the-art of the building blocks is reviewed and the anticipated progress within RTRO-Coal highlighted. Concepts are illustrated in examples demonstrating the value added. Gaps and further research and technical development required are identified, which will be conducted during the next years within RTRO-Coal.

2. RTRO-Coal: A Closed Loop Concept

The RTRO-Coal concept is based on the plan-do-check-act (PDCA) control cycle or also named closed loop concept. For mining operations this cycle can be interpreted as follows:
PPlan and Predict: Based on the resource model, strategic long-term mine planning, short-term scheduling and production control decisions are made. Performance indicators such as expected coal tonnage extracted per day, expected coal quality attributes and process efficiency are predicted.
DDo: The mine plan is executed.
CCheck: Production monitoring systems continuously deliver data about process indicators using modern sensor technology. For example the ash content of the coal extracted is monitored on a belt conveyor. Differences between model based predictions from the planning stage and actual measured sensor data are detected.
AAct: Differences between prediction and production monitoring are analyzed and root causes investigated. One root cause may be the limit of the resource model to predict the expected performance. Another root cause may be the precision of sensor measurements. Using innovative data assimilation methods, differences are then used to update the resource model and mine planning assumptions, such as losses and dilution.
With the updated resource and planning model, decisions made in the planning stage may have to be reviewed and adjusted in order to maximize the process performance and meet production targets. Figure 4 illustrates the building blocks of RTRO-Coal, which implements the PDCA cycle.
Figure 4. RTRO-Coal concept and main building blocks.
Figure 4. RTRO-Coal concept and main building blocks.
Minerals 05 00509 g004
BB1Optimization of long-term mine planning: Long-term mine planning is the first planning stage and aims to define the best extraction plan subject to a set of constraints imposed by economic, geological, environmental and safety considerations. In continuous surface coal mining this plan defines the annual panel geometries per mining bench over the life of the mine in a way that the stripping ratio is controlled and long-term targets met. These are usually in terms of coal quantity for several products and coal quality. The objective is usually to maximize the monetary value, such as the Net Present Value (NPV).
BB2Mining Simulator: Based on the long-term mine plan, short-term planning has to be performed. The mine simulator supports short-term decision making and production control. Using a set of decision variables including the weekly task schedule of the excavators, the short-term extraction sequence, dispatch decisions and stock-pile management, this simulator predicts a set of performance parameters for the process. This mine process simulator is based on discrete event simulation and is thus able to map the complex interaction between multiple excavators, mining logistics, dispatch options, waste management options, stockpiling and trainload; all linked to the resource model. Results are in terms of predicted indicators, which can be observed using production monitoring systems.
BB3Production monitoring sensors: In high standard coal mining operations, several sensor technologies are utilized to continuously measure equipment performance such as energy use for cutting, process performance such as system utilization, down times, coal and waste production and coal quality. RTRO-Coal builds upon these implemented technologies and aims to exploit their full value of information.
BB4Planning model update: A cornerstone of the RTRO-Coal concept is a method for rapid sequential resource model updating based on sensor data. Using differences between process performance indicators predicted using the mining simulator (BB2) and production monitoring data (BB3), the planning model shall be updated. The focus here is on the resource model, mapping the spatial distribution of coal seam geometry and quality attributes. The challenge arises from the fact that sensor measurements of high density but lower precision have to be integrated into a resource model, which is based on scarce but more precise exploration drill hole data. In addition, sensors may not directly measure coal attributes but are linked by some general function. Even linear combinations between mining blocks from different mining faces are possible, considering blending of coal from different mine areas during conveying and stockpiling.
BB5Short-term optimization: Having an updated resource model available, short-term mine planning decisions may have to be reviewed to find better or even optimal decisions. The complex interaction between all mining elements and the resource model does not allow formulating a closed form optimization problem to find better decisions. Therefore a simulation based optimization approach is chosen for a rapid and intelligent exploration of different combinations of short-term and production control decisions.
Recent developments and the expected progress within RTRO-Coal and these building blocks will be explained in the next section.

3. Progress within RTRO-Coal Building Blocks

The main aim of RTRO-Coal is to decrease risk in not meeting production targets in continuous coal mining operations. As discussed in the introduction, one main contributor to risk in mining is the limited knowledge about the details of the deposit. The ability to quantify the unavoidable uncertainty and to propagate this through the mining process, when using the mine process simulator, is key to understand the impact of resource model uncertainty on system performance. It is also required as a basis for resource model updating. Therefore this section first reviews the used methodology to capture geological uncertainty within RTRO-Coal, conditional simulation in geostatistics. Subsequently, the state-of-the-art of the mentioned building blocks is detailed, examples are illustrated and the necessary progress in research and technical development stated.

3.1. Capturing Geological Uncertainty

The majority of decisions in mining, such as equipment selection and specification, the optimization of a short- or long-term mine plan or the design of blending opportunities are based on the understanding of the orebody captured in the ore body model. Although estimated models can be considered to be good locally, they also exhibit a smoothing effect. To account for variability and grade uncertainty, methods of conditional simulation have increasingly been applied in geostatistical modelling over the last two decades [1,8]. Conditional simulation is a Monte-Carlo-Simulation-based technique that allows generating multiple possible models or scenarios of the deposit based on the information available, usually exploration drill holes. Each model is called realization and reproduces available data and information, statistics and spatial variability. In the terms of geostatistics, the generated models reproduce the representative data histogram and the variogram. Figure 5 shows a comparison between models generated by interpolation and simulation for a multi-seam coal deposit. A visual inspection of the models illustrates the differences very well. The interpolated model suggests a very smooth seam geometry and distribution of calorific value; however, this smoothness does not represent what was found in the data. Essentially, this smooth behavior does not represent reality. The two simulated models exhibit features inferred from data, namely the variability. Each realization captures the global structure of the deposit but exhibits a different behavior at a local scale.
Figure 5. Comparison between deposit models based on interpolation and simulation in geostatistics (reproduced after [9]).
Figure 5. Comparison between deposit models based on interpolation and simulation in geostatistics (reproduced after [9]).
Minerals 05 00509 g005
Analyzing the spread of values from different realizations at a location, say a mining block, allows for quantifying uncertainty in prediction and inferring probabilities of exceeding certain thresholds. Various case studies about the value added when using conditional simulation techniques in coal mining are documented in literature e.g., [10,11,12,13].
For practicality and acceptance of these conditional simulation techniques as a standard tool in industry, some challenges have to be overcome, including the size of simulations, computational efficiency and data management. Large coal deposit models, frequently discretized by up to millions grid nodes, need to be simulated. The development of algorithms for mining applications in general has taken this requirement into account. Dimitrakopoulos and Luo [14] suggest the theoretical background for a computationally efficient method, the Generalized Sequential Gaussian Simulation (GSGS). This sequential simulation approach simulates groups of clustered nodes simultaneously instead of node-by-node, which decreases computing time. Benndorf [9] demonstrates the applicability and computational benefit of GSGS in large coal deposits. Recently, this technique was combined with the minimum/maximum autocorrelation factors (MAF) decorrelation method for jointly simulating multiple correlated attributes, such as roof and floors in a lithological seam sequence [15].
With these techniques a toolset is available in general, but as well for RTRO-Coal, that enables a scenario-based modelling of the coal resource that captures uncertainty in prediction.

3.2. Optimization of Long-Term Mine Planning in Continuous Mining Operations

Long-term mine planning and production scheduling aim to define the “best” mine plan subject to the constraints imposed by physical and geological conditions, policies and the operational mining approach. The term “best” is defined by management objectives. These typically include maximizing the monetary value of the mining project as well as meeting customer expectations and guaranteeing a safe operation.
Methods of mathematical optimization, such as linear programming LP (e.g., [16]) or mixed integer programming MIP [17,18,19] have been successfully applied for over three decades to find optimal solutions for the defined problem. However, applications were mainly focused on discontinuous block mining in diffuse deposits. For continuous mining operations, such as lignite deposits, only very few applications are known to the authors. For example, Kawalec and Specylak [20] report a simplified application of open pit design optimization to a lignite deposit located in the Belchatow field in Poland using the commercially available Whittle software. For the first time, Minnecker et al. [21] introduced a new multi-objective MIP-model for coal-quality driven long-term extraction mine planning, tailored to continuous mining operations. Constraints developed honor the practical restriction of a continuous extraction system: first the complete mining pass has to be excavated before the belt conveyor can be moved and the next mining pass is accessible. Figure 6 illustrates the general division of the deposit in mining benches (BE) and the geometry of the block model, which results from the continuous mining system pivoting around a central point. The quality driven optimization approach allows defining upper and lower limits for critical coal quality parameters, e.g., calorific value and Fe2O3 in ash. The optimizer balances out the annual advance of each bench (Be) under the given constraints to meet targets as good as possible. Figure 7 shows the expected quality for an optimized plan for two products, dust coal (T1) and boiler coal (T2). As can be seen, the calorific value is well balanced out between the years of production. Due to an increased Fe2O3 content in this particular part of the deposit, meeting this production target will be a challenge during the illustrated time span.
An extension of this approach to integrate different scenarios of the coal deposit based on conditional simulation was suggested and tested by [22]. As a result the optimized long-term mine plans have a high probability of meeting production targets given the uncertain nature of the knowledge about the details of the deposit.
RTRO-Coal adopts this approach for optimizing the long-term mine plan. A next step is to investigate the feasibility of short-term mine planning and daily production within the boundaries defined by the optimized long-term plan. RTRO-Coal will investigate options for a new integrated short-term/long-term approach. So far such an approach is not known by the authors. A first discussion of potential approaches is given in the section on future research.
Figure 6. Schematic bench design and block model layout for optimizing continuous mining operations (reproduced after [21]).
Figure 6. Schematic bench design and block model layout for optimizing continuous mining operations (reproduced after [21]).
Minerals 05 00509 g006
Figure 7. Prediction of expected coal quality produced during the next periods when executing the optimized long-term plan (reproduced after [21]).
Figure 7. Prediction of expected coal quality produced during the next periods when executing the optimized long-term plan (reproduced after [21]).
Minerals 05 00509 g007

3.3. Process Simulation of Continuous Mining Operations

Continuous mining systems containing multiple excavators, producing multiple products of raw materials, are highly complex and exhibit strong interdependencies between constituents. A network of conveyor belts is used for transportation of the extracted materials to the different waste dumps or the coal stockpile. Techniques of stochastic process simulation, whether discrete, continuous or combined [23], provide a powerful tool for measuring performance indicators of complex systems. In the past few years there has been a large development in applications of process simulation in the mining industry. For example Panagiotou [24] described the application of the simulation program SIMPTOL for opencast lignite mines that use bucket wheel excavators (BWEs), conveyors and stackers. The main objective was to select and match the equipment to fit material characteristics while meeting production requirements and mine profiles. Michalakopoulos et al. [25] presented the simulation model of an excavation system at a multi-level terrace mine using the GPSS/H simulation language. The principal model output variables are production and arrival rate at the transfer point of mineral and waste. Later on [26] utilize the Arena simulation software for the simulation of Kardia Field mine in Greece. The validation of results illustrates an acceptable agreement with the actual data. Fioroni et al. [27] used discrete tools for the simulation of the continuous behavior of a conveyor belt network in a large steelmaking company. The authors proposed a modelling approach of the flow process, which uses portions of materials, which that are treated as discrete entities in simulation modelling. The results demonstrated that this technique was valid and successful.
As a literature demonstrates, stochastic process simulation is a potent method for measuring the Key Performance Indicators (KPIs) in continuous mining systems. However, the investigation of the impacts of geological uncertainty in the performance of continuous mining systems is still seen as a major gap. Within RTRO-Coal a new stochastic based mine process simulator was developed focusing on the effects of geological uncertainty to predict mine process performance and reliability. KPI’s of the mining system are defined within RTRO-Coal as the ability to meet coal quality and quantity targets and also the utilization and efficiency of the system. Potential KPI’s to be evaluated for each simulation replication are presented in Table 1. More details about the mathematical formulation and the evaluation function are discussed in [28].
To account for geological uncertainty, the concept of RTRO-Coal combines the two simulation concepts, geostatistical simulation for capturing geological uncertainty and stochastic process simulation to predict the large continuous mining system’s performance and reliability. Figure 8 shows the integrated simulation approach. As such it incorporates the timely and spatial varying nature of mining problems. With the deposit models representing spatial variability of characteristics and the extraction sequence representing availability and projected capacity over time the spatial and timely variability of the extraction system are fully captured in the simulator.
The output of the simulator is the set of values for each KPI. At this stage, penalties are applied when deviating from production targets. The KPI’s are summarized in an evaluation function, which results in a probability distribution when multiple replications are evaluated.
Table 1. The parameters of the evaluation function related to the Key Performance Indicators (KPI’s).
Table 1. The parameters of the evaluation function related to the Key Performance Indicators (KPI’s).
ParameterDescription
ObjectiveEvaluation of aggregated KPI’s of each simulation replication based on the pre-defined short-term planning targets.
KPIsJ1Coal quality: should be between defined lower and upper limit otherwise penalties are applied.
J2Coal quantity: should be between defined lower and upper limit otherwise penalties are applied.
J3Utilization: average utilization of the system can be concluded from the average utilization of excavators.
Decision VariablesTask schedules: different alternatives for short-term plans of mine (daily/weekly/monthly).
Extraction sequences: sequence of extracting mining blocks for each excavator.
Stockpile management: Stacking and reclaiming sequence and inventory.
Planned extraction rate of excavators for different time intervals.
ConstraintsEach block can be mined just once.
Conveyor belts can only be moved further along if all the blocks in one pass are mined out.
Figure 8. Integrated simulation approach (reproduced after [28]).
Figure 8. Integrated simulation approach (reproduced after [28]).
Minerals 05 00509 g008
For illustration, Figure 9 shows the schema of a typical open cast mine using continuous mining technology. The mining operation uses six excavators at six benches. The material extracted is transported by conveyor belts to the mass distribution center. Here, destinations are determined based on the type of material and based on the excavator from which the material originates. Finally, waste materials are conveyed to spreader 1 or 2 and the coal to the stockpile yard.
A resource block model is provided. For comparison, a block model was generated based on estimation and simulation in geostatistics. In addition, for benchmarking a synthetic reality was reconstructed based on historical mine data.
Figure 9. Schematic view of the problem (opencast mine).
Figure 9. Schematic view of the problem (opencast mine).
Minerals 05 00509 g009
Table 2 and Table 3 summarize general information and technical parameters that are used for simulation model building.
Table 2. Parameters related to equipment.
Table 2. Parameters related to equipment.
TypeTheoretical Capacity (loose m3/h)Scheduled Time Tscheduled (h)
Excavator 14900152
Excavator 24900152
Excavator 33770144
Excavator 41400168
Excavator 53770152
Excavator 6740152
Spreader 110,000168
Spreader 210,000168
Conveyor belts6000168
Table 3. Parameters related to targets.
Table 3. Parameters related to targets.
Material TypesTargetsPenalties
TypeDensityMaxMinUpperLower
Coal Quantity1322,700 t316,000 t11
Coal QualityAsh content < 8.5%1
To illustrate the value of the integrated simulation approach for this specific example, the KPI J1 is investigated, which is the ability to meet the coal quality target, in particular the ash content. Figure 10 shows the ash content for a week of production to be delivered by trains to power plants. Different resource block models were used as input, an estimated model using Kriging, a set of realizations using conditional simulation and the exhaustively known data set (reality). Results reveal that predictions based on the estimated model (black line) and the reality (dark grey line) are not well correlated. Reasons for this effect are the smoothing effect and the introduction of a conditional bias. If based on predictions on the basis of estimated models control decisions are made, it cannot be guaranteed that these decisions will lead to optimal results. Contrary, considering the conditional simulation model, there are 20 realizations (light grey cloud) and the average of the realizations (red line). Comparing geostatistical simulation based predictions with the reality; the red line generally follows the true ash content very well. Differences are in the expected range of deviations which are mapped by the shadow range (realization cloud).
Figure 10. The average ash content in the delivered trains (reproduced after [28]).
Figure 10. The average ash content in the delivered trains (reproduced after [28]).
Minerals 05 00509 g010
The previous example illustrates that the integrated simulation approach is a valid and powerful tool to explore the effect of geological uncertainty on the expected performance of complex continuous mining systems. It provides a valuable tool to the mine planning engineer to foresee critical situations affecting the continuous and reliable supply of raw material. More examples are given in [28]. The simulator is a key building block within RTRO-Coal and both, ingredient for updating the resource model and basis for the simulation-based optimization.

3.4. Sensors for Production Control

Sensors for production control are operational standard in lignite mining. Further technical development is not in scope of RTRO-Coal. However, online sensor information from production monitoring forms the foundation of real-time reconciliation and optimization of the process. Without going into much detail, a selected listing of available data is provided next:
  • GPS coordinates of the bucket wheel (extraction location),
  • material tracking systems and belt scales,
  • online coal quality analysis on belt conveyors or excavators,
  • machine performance data such as energy usage, effective digging capacity and downtimes.
Integrating these data, the material scanned on the belt conveyor can be directly linked to its origin in the deposit and as well linked to the machine performance of the excavator. This provides a tremendous data base to understand the system performance as a function of material characteristics.

3.5. Resource Model Updating Based on Sensor Data

This section introduces a framework for real-time feedback of sensor derived online data into the resource model. The framework consists of three parts: (1) a model based forecast at the sensor station; (2) sensor measurements; and (3) posterior updating of the resource model based on differences between model based prediction and sensor data. The latter one is a challenging task. The material stream passing a sensor station may be composed from different sub-streams coming from different excavators working at different parts in the deposit. Figure 11 illustrates this case for a continuous open pit mine. The raw material is mined on multiple benches. The flow of material is combined leading to the coal stock and blending yard. If the sensors are located above the central conveyor it is difficult to track back the differences between model based prediction and sensor measurement as the raw material stream originates from multiple different sources with different associated prediction accuracies in the resource models. In this respect, the accuracy of the sensor has to be taken into account as well.
Figure 11. Closed-loop concept in a continuous mining operation (reproduced after [29]).
Figure 11. Closed-loop concept in a continuous mining operation (reproduced after [29]).
Minerals 05 00509 g011
To account for different data originating from different sources with a different data quality, density and support, the currently used methods in geostatistical modelling and data fusion have to be extended. To solve these challenges multiple solutions are possible. Benndorf [29] proposes a modification of Kalman-Filter techniques, which are designed to sequentially estimate the system states, in this case the local grades at excavation locations, recursively on the basis of noisy input data measured. Kalman [30] introduced a method in the context of system and control theory, describing a recursive solution to estimate the state of a stochastic process Zt+1 at time t+1 based on a prior model of the state Zt at time t and observations l at time t.
To update a spatial resource model, the system state can be seen in a spatial content and it represents the block model estimate (x), and the observations correspond to sensor measurements during a production period of a certain time span, e.g., 5 min or 1 h.
The underlying idea is to update the resource model, denoted by Zt+1 (x), as a linear combination of the prior block model Zt(x) and the difference between model based prediction and the vector of sensor based measurements l (Equation 1).
Z t + 1 ( x ) = Z t ( x ) + K ( l A Z t ( x ) )
Matrix A is a design matrix and captures the contribution of each reserve block per time interval to the raw material flow produced and observed at a sensor station. The term AZt(x) represents the model-based prediction and integrates the operative decisions (digging capacity and location of excavators at each time) in A and the prior resource/reserve model Zt(x). The objective is to determine the matrix K, which is the unknown updating factor, in literature referred to as Kalman-Gain (e.g., [31]), as a best linear and unbiased estimator. A detailed derivation is not scope of this paper and the reader is referred to [29]. It can be shown that
K = ( A T C Z Z t A + C l l ) 1 A T C Z Z t
An interpretation of equation (2) reveals the integrative character of the Kalman-Gain. The first term is the inverse of two error sources: (a) the model prediction error, represented by the covariance matrix of the prior resource model C Z Z t , which is propagated through the mining system by the design matrix A and (b) the measurement error, represented by the covariance matrix of the sensor-based measurement C l l . The second term represents again the error source of the model-based prediction. A comparison of potential magnitudes of the two error terms reveals that:
● if the model error is large and the measurement error of data small, the Kalman-Gain K tends towards 1. The application to equation (1) shows that the full difference between model-based prediction and sensor-based measurement is taken into account to update the resource/reserve model.
● if the model error is small and the measurement error of data large, the Kalman-Gain K tends towards 0. The application to equation (1) indicates that the difference between model-based prediction and sensor-based measurement is not taken into account to update the resource/reserve model. The precision of the sensor is too low to add value to the estimation of resources and reserves.
The traditional method is limited to normally distributed errors and linear relationships in the design matrix A. These assumptions are not always valid in mineral resource extraction, as coal qualities may not be distributed normally and reserve estimation includes non-linear elements, such as minimum mining thicknesses, losses and dilutions. Expression (3) would not be valid. The so called N-Score Ensemble Kalman-Filter (EnKF) (e.g., [32]), offers a solution, which is founded upon the Monte-Carlo concept. Based on an ensemble of possible scenarios of the resource model, which capture the uncertainty and variability in estimation, the application of equation (1) to each of the ensemble members leads to updated scenarios. A statistical evaluation of the updated models leads to an empirical representation of the new model error C Z Z t + 1 . The Ensemble members can be generated using commonly applied techniques of conditional simulation in geostatistics (e.g., [1]).
The subsequent example aims to investigate the performance of the proposed updating methodology. Here, an artificial test case presented, which is built around the well-known and fully understood Walker Lake data set [33]. The data set (Figure 12) is interpreted as a quality parameter of a coal deposit, e.g., as ash content and is integrated in a typical mine topography. It is sampled irregularly at a spacing corresponding to an average of two reserve block lengths. The blocks were defined with a dimension of 16 m × 16 m × 10 m. The block-variogram is given with a spherical structure, range 50 m, nugget effect 0.4 and sill 0.6.
Figure 12. Example for resource model updating in a mine.
Figure 12. Example for resource model updating in a mine.
Minerals 05 00509 g012
Taking an assumed density of 2 t/m3 into account, one mining block represents a tonnage of 5.120 t. Ordinary Kriging was used to generate a resource block model and the prior error covariance matrix, Generalized Sequential Gaussian Simulation was used to derive the realizations or ensemble members for the EnKF application. For simplicity, no dilution and losses were applied resulting in the reserve model being equal to the resource model. The resulting block model (Figure 12) was used as the prior model.
The artificial block model shall be mined applying a continuous mining system, which initially consists of two bucket-wheel excavators positioned at separate benches. Different digging rates were applied to each excavator as specified in Table 2. The material is discharged on belt-conveyors positioned on the benches, which are combined to one material flow at the central mass distribution point. The belt speed is assumed to be constant at 6 m/s.
The combined material flow of two excavators is scanned by a sensor positioned above a central conveyor feeding the stock- and blending yard. Since no real sensor data are available, virtual sensor data were generated. The artificial sensor data represent a 10 min moving average (corresponding to about 250 t of production) and are composed of three components. Component one is the true block grade taken from the exhaustively known data set. Component two captures the volume variance relationship and corrects the smaller sensor-measurement support of 250 t to the mining block support of 5120 t by adding the corresponding dispersion variance. The third component mimics the precision of the sensor. For this case study the relative sensor error is varied between 1%, 5% and 10%.
The performance of the proposed updating approach is evaluated using the mean square difference or mean square error (MSE) related to the true block value. Here, the difference between estimated block value Zt+1(x) and real block value Z(x) from the exhaustive data set is compared. The MSE is an empirical error measure and can be calculated according to
M S E = 1 N i = 1 N ( z t + 1 ( x i ) z ( x i ) ) 2
Figure 13 shows the MSE for different sensor precisions compared to the prior case for blocks,
  • which are already mined,
  • which are one block distant and will be mined during next working shift, day or week and
  • which are two blocks distant and will be mined in the near future.
The upper row shows results from the Kalman-Filter, the lower row shows results obtained by the Ensemble Kalman Filter.
Figure 13. Evaluation of results for resource model updating using the Kalman-Filter (KF) and the Ensemble Kalman-Filter (EnKF) (reproduced after [29]).
Figure 13. Evaluation of results for resource model updating using the Kalman-Filter (KF) and the Ensemble Kalman-Filter (EnKF) (reproduced after [29]).
Minerals 05 00509 g013
Figure 13 clearly demonstrates the ability of the presented Kalman-Filter based approach to decrease the uncertainty of predicting block values by updating based on sensor data. Considering the MSE, the following observations can be made:
• For mined blocks, the uncertainty almost vanishes. This is expected because blocks are mined. Residual uncertainties remain due to the sensor precision and the ability to track back the differences to its origin.
• Adjacent blocks are updated resulting in a significant improvement compared to the prior model. For high precision sensors this improvement leads to an about 40% decrease of the MSE. This improvement is due to the positive covariance between two adjacent blocks. In addition, the sensor clearly influences the result.
• Blocks in the second next row are still updated. Due to the larger distance and the corresponding smaller covariance, the effect is less obvious compared to directly adjacent blocks, however, still significant.
With this methodology an updating framework is presented that allows for a sequential integration of production data to continuously improve the resource model. In the next research stage of RTRO-Coal, the validated concept will be applied to a full scale 3D resource model and implemented in a direct mining environment. A bench-marking exercise using historical production monitoring data will be used to calibrate the method.

3.6. Simulation-Based Optimization for Short-Term Mine Planning

The updated resource model possibly will lead to new decisions in short-term operation management such as production sequencing, digging capacity control or stock-pile management. A particular example is to optimize equipment utilization as a function of material management. Consider two scenarios A and B. In scenario A, on a given bench, an excavator has two types of material, coal and waste. The demand of coal and waste differs due to blending constraints and available dump space on the spreader site of the open pit. The objective here is to optimize the sequence of extraction and effective digging rates of individual excavators in a way, which minimizes downtime of equipment due to lack in demand. In scenario B, on a given bench, the excavator has two material types to dig, dry and wet material. The extraction sequence hast to be coordinated in a way, which follows a geotechnical stable dumping sequence of waste material on the dump site. The optimization task is to coordinate the extraction sequence of multiple excavators that the available dump space for wet material is utilized best possible while minimizing downtimes of excavators due to waiting on available dump space.
Methods of mathematical programming, such as Dynamic Programming or Mixed Integer Programming, are well acknowledged in the field of mine planning optimization. Most of the mathematical programming approaches are limited by the amount of decision variables, as applications become large and suffer from reduced computational efficiency. In leading manufacturing process industries, such as aerospace, chemical industry or petroleum engineering, the simulation approach is applied to support making expensive decisions and optimization during design and operation of processes [34,35,36]. Simulation based optimization methods (Figure 14), such as Response Surface Methods or Learning Automata Search, have been proven to result in near optimal solutions for decision problems and are especially applicable for scheduling complex and computationally large systems [37], such as continuous mining operations. The concept of simulation based optimization is shown in Figure 14. Using general system simulation techniques the objective value J of a complex objective function can be evaluated for a given set of decision variables. The optimization part, such as Response Surface Methods in combination with gradient descent methods explores the space of decision variables to obtain a near to optimal set of these.
Figure 14. The concept of simulation based optimization.
Figure 14. The concept of simulation based optimization.
Minerals 05 00509 g014
Based on the mine system simulator, RTRO-Coal will explore methods of simulation-based optimization applied to continuous mining systems. To evaluate suitable approaches for the applicability to short-term mine planning of continuous mining systems, the following problem characteristics have to be taken into account:
● The optimization problem consists of discrete decision variables, which determine the extraction sequence of the material (scheduling problem), as well as continuous decision variables to control the effective digging capacities within certain boundaries.
● To provide a detailed enough resolution for scheduling, the amount of decision variables can become rather large resulting in a large-scale optimization problem.
● The objective function value is quantified by a simulator that considers the geological uncertainty, unscheduled breakdowns of equipment, and the uncertain quantity demand of customers. One simulation run might take some time. Therefore, an optimization algorithm is desirable that does not need to call the simulator too often.
● The objective function value is obtained by summing up the weighted system KPIs, which are calculated using outputs generated by a simulator. It can be expected that the design problem is multimodal, consisting of multiple local optima. Consequently, a global optimization mechanism is required that prevents the optimization process from getting trapped in a local optimum.
● Due to the continual gain of additional information during the extraction process, that can be used to update the planning model, the short-term mine planning problem will be re-optimized frequently. Consequently, one optimization run should not take too long.
A first review of simulation based optimization methods resulted in a set of preferred methods for optimizing short-term planning in continuous mining operations [38]. Next steps involve prioritizing methods, implementing and comparing, validation studies as well as full scale applications in a mining environment.

4. Discussion and Future Research

With the building blocks described in the previous section, a framework has been compiled that will enable near real-time updating of coal resource models in conjunction with an optimization of short-term decisions and production control. Necessary algorithms and methods of building blocks have been theoretically developed and tested in a controlled environment. During the next project phase these methods will be implemented and tested in industrial field applications.
With the learnings about the performance of short-term planning, RTRO-Coal will provide new insights into the interaction between resource and extraction process efficiency on a small time scale, which will also effect long-term mine planning and exploration. The following questions could be asked:
● Is it feasible to execute the short-term mine plan within the boundaries set by the long-term plan?
● What is the cost of lost flexibility in short-term planning and production caused by boundaries imposed by the long-term plan?
● Having the new insight obtained by the resource model update and considering practical operating constraints, is the long-term plan still optimal?
These questions lead to the future research topic of integrated short- and long-term planning. Essentially, both approaches aim to maximize some monetary benefit, long-term planning is more NPV-focused whereas short-term planning aims to meet targets on a daily basis. RTRO-Coal will investigate options to integrate short- and long-term planning. The basic concept behind it is an iterative optimization to balance out necessary flexibility in short-term planning with long-term optimality in NPV. The idea is to introduce a relaxed short-term planning optimization, which will be performed without considering strict boundaries imposed by the long-term plan. The degree of flexibility in short-term planning will be measured using penalties for blocks, which are scheduled by the short-term scheduler in different long-term periods. By varying penalties and investigating the effect on production costs, the value of flexibility or the costs of strictly following the long-term plan can be evaluated. Adjustments of the long-term plan can then be derived by comparing the loss in long-term NPV with the gain through more flexible short-term planning.
Another interesting question concerns the additional information content and value generated by integrating production monitoring data. What is the value of additional data? Is it even worth investing additional research into production monitoring? Also, one may question the level of exploration. Is it still necessary to drill exploration holes on a grid as currently done or would the additional utilization of sensor information allow increasing the exploration drill hole spacing?
Potential answers to these questions show the tremendous potential behind the RTRO-Coal framework in efficiency improvement. Further research and technical development is necessary to remove some of the questions marks.

5. Conclusions

Online data from production monitoring provide a valuable and comprehensive source of information. The RTRO-Coal framework is designed to exploit the full value of these data by the means of a closed-loop feedback cycle. By continuously analyzing model based predictions with actual measurements it promotes a transition from a discontinuous batch type process of resource model reconciliation and optimization of production control to a continuously optimized process control.
Main building blocks are formed by the application of state-of-the-art data assimilation techniques for sensor based resource model updating and simulation based optimization algorithms for short-term decisions and production control.
Preliminary results of case studies promise a significant increase in resource recovery and process efficiency. For a validation of this statement, large scale industrial field tests will be conducted as a proof of concept during the next project stage. Further research will focus on integrating strategic long-term planning with short-term production control to balance optimality in NPV with achieving short-term production goals. Also the value of additional information will be investigated leading to new exploration concepts, where infill drilling for operational planning may be reduced and replaced by online production monitoring data

Acknowledgements

The RTRO-Coal project has received funding from the European Union’s Research Fund for Coal and Steel RFCS under grant agreement No. RFCR-CT-2013-00003.

Author Contributions

This article represents a joint effort from the team of authors. Following listing provides information on, which parts were contributed by the authors. Main text: Jörg Benndorf. Introduction and Section 2 : Jörg Benndorf with support from Heinrich Rosenberg, Thomas Thielemann, Oliver Lohsträter and Matthias Lindig. Section 3.1: Jörg Benndorf and Wojciech Naworyta. Section 3.2: Corinna Minnecker and Ralf Donner with support from Wojciech Naworyta. Section 3.3: Masoud Soleymani Shishvan with support from Heinrich Rosenberg and Thomas Thielemann. Section 3.4: Jörg Benndorf. Section 3.5: Cansin Yueksel with support from Oliver Lohsträter and Matthias Lindig. Section 3.6: Corinna Minnecker, Jörg Benndorf and Masoud Soleymani Shishvan. Discussion and Conclusion: Jörg Benndorf with support from Heinrich Rosenberg, Thomas Thielemann, Oliver Lohsträter and Matthias Lindig.

Conflicts of Interest

The authors declare no conflict of interest.

References and Notes

  1. Chiles, J.P.; Delfiner, P. Geostatistics, Modelling Spatial Uncertainty; John Wiley & Sons: New York, NY, USA, 2012. [Google Scholar]
  2. Rosenberg, H. Detection of materials and deposits as a basis for innovative operations management systems employed as part of opencast mine process optimizations. World Min. Clausthal Zellerfeld 2007, 59, 173–180. [Google Scholar]
  3. Knipfer, A. Decision support for operating lignite mines with high geological variability based on mine surveying and production monitoring. Bergbau Zeitschrift für Rohstoffgewinnung Energie Umwelt 2012, 4, 148–152. (In German) [Google Scholar]
  4. Sládková, D.; Kapica, R.; Vrubelm, H. Global navigation satellite system (GNSS) technology for automation of surface mining. Int. J. Min., Reclam. Environ. 2011, 25, 284–294. [Google Scholar] [CrossRef]
  5. Scholze, P.; Koehler, U. Complex control functions and management systems in the opencast mines of Vattenfall Europe Mining AG. World Min. GdmB 2012, 1, 31–39. [Google Scholar]
  6. Gärtner, D.; Hempel, R.; Rosenberg, H. Market-Oriented, Flexible and Energy-Efficient Operations Management in RWE Power AG’s Opencast Mines. In Proceedings of the 12th International Symposium Continuous Surface Mining—Aachen 2014; Niemann-Delius, C., Ed.; Springer International Publishing: Gewerbestrasse, Switzerland, 2015; pp. 339–353. [Google Scholar]
  7. Buxton, M.; Benndorf, J. The Use of Sensor Derived Data in Real-Time Mine Optimisation: A Preliminary Overview and Assessment of Techno-Economic Significance. In Proceeding of the 142nd SME Annual Meeting and Exhibit, Denver, CO, USA, 24–27 February 2013; pp. 13–38.
  8. Dimitrakopoulos, R. Advances in Orebody Modelling and Strategic Mine Planning I; The Australian Institute of Mining and Metallurgy (AusIMM): Melbourne, Australia, 2010; p. 334. [Google Scholar]
  9. Benndorf, J. Application of efficient methods of conditional simulation for optimizing coal blending strategies in large continuous open pit mining operations. Int. J. Coal Geol. 2013, 112, 141–153. [Google Scholar] [CrossRef]
  10. Naworyta, W.; Sypniowski, S.; Benndorf, J. Planning for reliable coal quality delivery considering geological variability: A case study in polish lignite mining. J. Qual. Reliab. Eng. 2015, 2015. [Google Scholar] [CrossRef]
  11. Jurek, J.; Mucha, J.; Wasilewska-Błaszczyk, M. Overview of geostatistics applications for estimation of parameters of Polish lignite deposits. Zeszyty Naukowe Instytutu Gospodarki Surowcami Mineralnymi i Energią PAN 2013, 85, 143–153. (In Polish) [Google Scholar]
  12. Naworyta, W.; Benndorf, J. Accuracy assessment of geostatistical modelling methods of mineral deposits for the purpose of their future exploitation—Based on one lignite deposit. Gospodarka Surowcami Mineralnymi Miner. Resour. Manag. 2012, 28, 77–101. [Google Scholar] [CrossRef]
  13. Costa, J.F.; Zingano, A.C.; Koppe, J.C. Simulation an approach to risk analysis in coal mining. Explor. Min. Geol. 2000, 9, 43–49. [Google Scholar] [CrossRef]
  14. Dimitrakopoulos, R.; Luo, X. Generalized sequential Gaussian simulation on group size ν and screen-effect approximations for large field simulations. Math. Geol. 2004, 36, 567–591. [Google Scholar] [CrossRef]
  15. John, A. Complex 3D modelling of lignite deposits using geostatistical simulation—From raw data to a validated model. Bergbau Zeitschrift für Rohstoffgewinnung Energie Umwelt. 2014, 2, 62–67. (In German) [Google Scholar]
  16. Johnson, T.B. Optimum Open Pit Mine Production Scheduling; University of California Berkeley Operations Research Center: Berkeley, CA, USA, 1968. [Google Scholar]
  17. Gershon, M.E. Optimal mine production scheduling: Evaluation of large-scale mathematical programming approaches. Int. J. Min. Eng. 1983, 1, 315–329. [Google Scholar] [CrossRef]
  18. Ramazan, S.; Dimitrakopoulos, R. Recent applications of operations research and efficient MIP formulations in open pit mining. SME Trans. 2004, 316, 73–78. [Google Scholar]
  19. Benndorf, J.; Dimitrakopoulos, R. Stochastic long-term production scheduling of iron ore deposits: Integrating joint multi-element geological uncertainty. J. Min. Sci. 2013, 49, 68–81. [Google Scholar] [CrossRef]
  20. Kawalec, W.; Specylak, J. Open Pit Optimisation of a Lignite Deposi. In Mine Planning and Equipment Selection; Balkema: Rotterdam, The Netherlands, 2000; pp. 217–222. [Google Scholar]
  21. Minnecker, C.; Benndorf, J.; Lohsträter, O.M. Optimizing of Long-Term Mine Planning in Large Lignite Deposits. In Mine Planning and Equipment Selection; Drebenstedt, C., Singhal, R., Eds.; Springer International Publishing: Gewerbestrasse, Switzerland, 2014; pp. 113–124. [Google Scholar]
  22. Innovative Braunkohlen Integration in Mitteldeutschland–Ibi. Available online: http://tu-freiberg.de/sites/default/files/media/institut-fuer-markscheidewesen-und-geodaesie-12465/forschung/ibi/ibi-vp12_schlussbericht_tib.pdf (accessed on 19 August 2015).
  23. Kelton, W.D.; Law, A.M. Simulation Modeling and Analysis, 3rd ed.; McGraw Hill: Boston, MA, USA, 2000. [Google Scholar]
  24. Panagiotou, G.N. Computer Simulation of the Mining Operations in Opencast Lignite Mines Operating BWEs, Conveyors and Stackers. In Proceedings of the First Conference on Use of Computer in the Coal Industry, New York, NY, USA, 1–3 August 1983; pp. 150–157.
  25. Michalakopoulos, T.N.; Arvaniti, S.; Panagiotou, G.N. Simulation of a Continuous Lignite Excavation System. In Proceeding of the Fourteenth International Symposium on Mine Planning and Equipment Selection (MPES), Banff, AB, Canada, 31 October–2 November 2005.
  26. Michalakopoulos, T.N.; Roumpos, C.P.; Galetakis, M.J.; Panagiotou, G.N. Discrete-Event Simulation of Continuous Mining Systems in Multi-Layer Lignite Deposits. In Proceedings of the 12th International Symposium Continuous Surface Mining—Aachen 2014; Springer International Publishing: Gewerbestrasse, Switzerland, 2015; pp. 225–239. [Google Scholar]
  27. Fioroni, M.M.; Franzese, L.A.G.; Zanin, C.E.; Fúria, J.; de Toledo Perfetti, L.; Leonardo, D.; da Silva, N.L. Simulation of Continuous Behavior Using Discrete Tools: Ore Conveyor Transport. In Proceedings of the 39th Conference on Winter Simulation: 40 Years! The Best is yet to Come, Washington, DC, USA, 9–12 December 2007; pp. 1655–1662.
  28. Shishvan, M.S.; Benndorf, J. Performance Optimisation of Complex Continuous mining System Using Stochastic Simulation. In Engineering Optimisation; Taylor and Francis: London, UK, 2015; pp. 273–278. [Google Scholar]
  29. Benndorf, J. Making use of online production data: Sequential updating of mineral resource models. Mathem. Geosci. 2015, 47, 547–563. [Google Scholar] [CrossRef]
  30. Kalman, R.E. A new approach to linear filtering and prediction problems. J. Basic Eng. 1960, 82, 35–45. [Google Scholar] [CrossRef]
  31. Welsh, G.; Bishop, G. An Introduction to the Kalman Filter; University of North Carolina: Chapel Hill, NC, USA, 1995. [Google Scholar]
  32. Schoniger, A.; Nowak, W.; Hendricks Franssen, H.-J. Parameter estimation by ensemble Kalman filters with transformed data: Approach and application to hydraulic tomography. Water Resour. Res. 2012, 48. [Google Scholar] [CrossRef]
  33. Isaak, E.H.; Srivastava, R.M. Applied Geostatistics; Oxford University Press: New York, NY, USA, 1989. [Google Scholar]
  34. Jung, J.Y.; Blau, G.; Pekny, J.F.; Reklaitis, G.V.; Eversdyk, D. A simulation based optimisation approach to supply chain management under demand uncertainty. Comput. Chem. Eng. 2004, 28, 2087–2106. [Google Scholar] [CrossRef]
  35. Schulze-Riegert, R.; Shawket, G. Modern Techniques of History Matching. In Proceeding of the 9th International Forum on Reservoir Simulation, Abu Dhabi, United Arab Emirates, 9–13 December 2007; pp. 9–13.
  36. Subramaniam, G.; Gosavi, G. Simulation-based optimisation for material dispatching in Vendor-Managed Inventory systems. Int. J. Simul. Process Model. 2007, 3, 238–245. [Google Scholar] [CrossRef]
  37. Gosavi, A. Simulation-Based Optimisation: Parametric Optimisation Techniques and Reinforcement Learning, 2nd ed.; Springer: New York, NY, USA, 2003. [Google Scholar]
  38. Minnecker, C. Theoretical framework for simulation-based short-term mine planning optimization. Confidential consortium internal report of RTRO-Coal. 2015; 37. [Google Scholar]

Share and Cite

MDPI and ACS Style

Benndorf, J.; Yueksel, C.; Shishvan, M.S.; Rosenberg, H.; Thielemann, T.; Mittmann, R.; Lohsträter, O.; Lindig, M.; Minnecker, C.; Donner, R.; et al. RTRO–Coal: Real-Time Resource-Reconciliation and Optimization for Exploitation of Coal Deposits. Minerals 2015, 5, 546-569. https://doi.org/10.3390/min5030509

AMA Style

Benndorf J, Yueksel C, Shishvan MS, Rosenberg H, Thielemann T, Mittmann R, Lohsträter O, Lindig M, Minnecker C, Donner R, et al. RTRO–Coal: Real-Time Resource-Reconciliation and Optimization for Exploitation of Coal Deposits. Minerals. 2015; 5(3):546-569. https://doi.org/10.3390/min5030509

Chicago/Turabian Style

Benndorf, Jörg, Cansin Yueksel, Masoud Soleymani Shishvan, Heinrich Rosenberg, Thomas Thielemann, Robert Mittmann, Oliver Lohsträter, Matthias Lindig, Corinna Minnecker, Ralf Donner, and et al. 2015. "RTRO–Coal: Real-Time Resource-Reconciliation and Optimization for Exploitation of Coal Deposits" Minerals 5, no. 3: 546-569. https://doi.org/10.3390/min5030509

Article Metrics

Back to TopTop