Next Article in Journal
On the So-Called Gibbs Paradox, and on the Real Paradox
Previous Article in Journal
Entropy of Relativistic Mono-Atomic Gas and Temperature Relativistic Transformation in Thermodynamics
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

On Darcy-Brinkman Equation: Viscous Flow Between Two Parallel Plates Packed with Regular Square Arrays of Cylinders

by
Haidong Liu
,
Prabhamani R. Patil
and
Uichiro Narusawa
*
Department of Mechanical & Industrial Engineering, Northeastern University, Boston, Massachusetts 02115, U.S.A.
*
Author to whom correspondence should be addressed.
Entropy 2007, 9(3), 118-131; https://doi.org/10.3390/e9030118
Submission received: 12 December 2006 / Accepted: 5 September 2007 / Published: 11 September 2007

Abstract

:
Effects of the bounding solid walls are examined numerically for slow flow over regular, square arrays of circular cylinders between two parallel plates. A local magnitude of the rate of entropy generation is used effectively to determine the flow region affected by the presence of the solid boundary. Computed axial pressure gradients are compared to the corresponding solution based on the Darcy-Brinkman equation for porous media in which the effective viscosity appears as an additional property to be determined from the flow characteristics. Results indicate that, between two limits of the Darcian porous medium and the viscous flow, the magnitude of μ ^ (the ratio of the effective viscosity to the fluid viscosity) needs to be close to unity in order to satisfy the non-slip boundary conditions at the bounding walls. Although the study deals with a specific geometric pattern of the porous structure, it suggests a restriction on the validity of the Darcy-Brinkman equation to model high porosity porous media. The non-slip condition at the bounding solid walls may be accounted for by introducing a thin porous layer with μ ^ = 1 near the solid walls.

Introduction

The Darcy-Brinkman equation is a governing equation for flow through a porous medium with an extra Laplacian (viscous) term (Brinkman term) added to the classical Darcy equation. The equation has been used widely to analyze high-porosity porous media. The dynamic viscosity, μ e , associated with the Brinkman term is referred to as the effective viscosity. Studies in the past yielded varying results for the magnitude of the viscosity ratio, μ ^ ( = μ e / μ with μ = fluid viscosity) between slightly less than unity to as high as < ~ 10 for high porosity porous media [3,5,8,9,10]. The validity of the Darcy- Brinkman equation has also been a subject of investigation, particularly in relation to the boundary conditions at the solid- as well as fluid- interface [11,12]. In the present study our subject of interest is flow over regular square arrays of circular cylinders bounded at the top and the bottom by solid plates. The flow in the absence of the bounding walls is studied in detail by Sangani and Acrivos [15]. The analysis which solves the Navier- Stokes equations rather than the Darcy equation, yields a relation between the permeability of the regular array structure and the porosity (volume fraction occupied by the flow), confirming that the Darcy equation is valid for flow through regular structures over the whole spectrum of the porosity. Therefore, quantitative relations between the wall effects and the Darcy-Brinkman equation may be examined in a more focused manner through the present investigation. One of the objectives of the present analysis is to examine flow structure near the bounding walls. It is generally accepted that the effects of a solid boundary is confined within a thin boundary layer [12]. Our second objective is to test the feasibility of addressing the thin region by using the Darcy-Brinkman equation. The Darcy-Brinkman equation in recent years is employed in biomedical hydrodynamic studies [7], including its use in modeling a thin fibrous surface layer coating blood vessels (endothelial surface layer) as it is a highly permeable, high porosity porous medium [13,14,17]. A better understanding of the characteristics of the Darcy-Brinkman equation, therefore, is an important part of more practical problems; thus forming a motivation of the present report.

Analyses

As shown in Figure 1, we consider a steady, incompressible, fully-developed, very slow ( Re  (Reynolds number) 0 ) flow across regular square arrays of circular cylinders, bounded by parallel plates. Governing equations based on the Darcy-Brinkman equation for porous media and the boundary conditions are,
d p d x = μ K u s + μ e d 2 u s d y 2 ,       u s ( y = H ) = 0 ,       d u s d y ( y = 0 ) = 0
where p = pressure, u s = superficial velocity, K = permeability of porous medium. In terms of non-dimensional variables defined as, y ˜ = y / H , u ˜ = u s / u m ( u m = mean velocity = q / 2 H , q = volume flow rate per channel width), the formulation and its solution become,
H 2 μ e u m ( d p d x ) = 1 μ ^ H 2 K u ˜ d 2 u ˜ d y ˜ 2 ,       u ˜ ( y ˜ = 1 ) = 0 ,       d u ˜ d y ˜ ( y ˜ = 0 ) = 0 .
u ˜ = K μ u m ( d p d x ) [ 1 cosh ( D a y ˜ / μ ^ ) cosh ( D a / μ ^ ) ]
where μ ^ = μ e / μ (viscosity ratio), D a = H / K .
Figure 1. (a) Flow between two parallel plates filled with regular square arrays of circular cylinders, (b) Regular square arrays of circular cylinders.
Figure 1. (a) Flow between two parallel plates filled with regular square arrays of circular cylinders, (b) Regular square arrays of circular cylinders.
Entropy 09 00118 g001
Upon an integration of the governing equation, Eq.(2a), over the channel half-depth, H ,
noting   0 1 u ˜ d y ˜ = 1 ( u m = 0 H u d y / H ) ,
we obtain the following equation for the pressure gradient;
H 2 μ u m ( d p d x ) = D a 2 1 tanh ( D a / μ ^ ) D a / u ^
Since lim x 0 tanh x x x 3 / 3 , the viscous flow limit is reached as K , ( D a 0 ) ,
H 2 μ u m ( d p d x ) viscous limit = 3 μ ^ .
The viscous flow limit corresponds to the case of μ ^ = 1 in the equation above.
The Darcian limit of flow through a porous medium is recovered as K 0 , ( D a )
H 2 μ u m ( d p d x ) D a r c i a n L i m i t = H 2 K = D a 2 .
For the case of our interest, the porous medium consisting of regular square arrays of cylinders, the permeability, K , may be expressed as,
K = ( 2 l ) 2 f ( C ) ,       that is ,   D a = f ( C ) ( H 2 l )
where C (solid fraction) = 1 ϕ ( ϕ = porosity), 2 l = side length of a single square unit. (See Figure 1.) The function, f ( C ) , is given in an explicit form for high porosity arrays and in a graphical form for low porosity arrays in [15].
Figure 2. (a) Coordinates for formulation, Eq.(8). (b) Typical computational grid for a unit cell.
Figure 2. (a) Coordinates for formulation, Eq.(8). (b) Typical computational grid for a unit cell.
Entropy 09 00118 g002
Flow, conditions of which lie between the two limits of Eqs.(5,6), is investigated numerically. Referring to Figure 2, governing equations and boundary conditions are,
V = 0 ,       0 = p + μ 2 V       with   V = u i ^ + v j ^ .
u = v = 0       at   ( x , y ) = ( l x l , y = H )   and on cylinder surface,
u x = 0       at   ( x , y ) = ( ± l , 0 y H ) ,
u y = v = 0       at   ( x , y ) = ( l x l , y = 0 ) .
Two commercially-available computational programs for hydrodynamic analyses are used in our numerical experiments, FLUENT (by Fluent Inc.) and FEMLAB (by COMSOL Group). The former is used as the main program; while, the latter is employed to confirm results from the former. Eq.(8) is solved computationally as the porosity, ϕ , and the length ratio, H / l , are varied systematically. The porosity represents a fraction of the flow field in the cross sectional area of a ( 2 l × 2 l ) unit cell; while, the ratio, H / l (integer), indicates a number of cell layers over the channel depth. Figure 3 is presented to depict the range of the porosity of our investigation for the case of H / l = 10 . For the high porosity channel flow of ϕ = 99.99 % , the parabolic velocity profile of the viscous flow limit over the channel depth is disturbed by regularly placed arrays of small cylinders; while, at low porosity the flow may be approximated by the lubrication type flow through a narrow slot with the uniform Darcian flow velocity being modified by local geometric variations. Computations are performed in dimensional form under the following conditions:
μ = 0.001   [ k g / m s ] ,       l = 0.05   [ m ] ,
T ( t e m p e r a t u r e ) = 288.16   [ K ] ,       u m = 1 × 10 4   [ m / s ] .
Figure 3. Examples of flow field over a channel half-depth.
Figure 3. Examples of flow field over a channel half-depth.
Entropy 09 00118 g003
The computational procedure is outlined below:
  • Solve Eq.(8) and find the x-direction pressure gradient, d p / d x ), for a specified value of the porosity at the length ratio, H / l = 1 (that is, the case of a single unit cell over the channel). (Actual computations are performed over multiple longitudinal cell columns (5 - 10) to ensure that the periodic conditions at the cross-sectional cell boundaries are satisfied accurately.)
  • Increase the value of H / l by one, and repeat the computation.
  • In the case of H / l = 1 , the solid wall affects the entire flow field. As the magnitude of H / l increases, cells near the center of the channel (y = 0 in Figure 1) become less sensitive to the presence of the solid walls. Computation for a fixed value of porosity is terminated when the size of the wall-affected region becomes independent of H / l .
Sangani and Acrivos [15] reports solutions of the velocity field in a single unit cell (i.e. flow through square arrays of cylinders without solid bounding plates) by applying the least square collocation method [4] to a series solution, which satisfies a part of the required boundary conditions exactly. We used this solution for confirmation of the validity of our computational results as well as for determination of the required numerical conditions (number and size of the computational mesh as well as the conversion criteria). The validity of the computational results is confirmed by recovering the permeability, K , (Eq.(7)) reported in [15] over the range of 0.215 ( ϕ min i m u m (cylinders in contact with each other) < ϕ < 1 . When a unit cell becomes completely unaffected by the presence of the bounding walls, the velocity field should be identical to that of the solution in [15] everywhere in the cell. However, it is not easy to find the identity for the two-dimensional velocity field we are analyzing. Instead, the identity of the rate of entropy generation over a unit cell is used to find a degree of the wall effects on the flow field in the respective unit cell. The local volumetric rate of entropy generation over a unit width of the channel, S ˙ G / / /   [ W / m 2 K ] , is related to the dissipation function Φ   [ 1 / s 2 ] [1]. The rate of entropy generation per unit cell per width, S ˙ G , c e l l / , is evaluated for each cell located over the channel half-depth by numerically integrating the following equation for volumetric rate of entropy generation due to the viscous dissipation,
S G / / / = μ T Φ     where   Φ = 2 ( ( u x ) 2 + ( v y ) 2 ) + ( u y + v x ) 2

Results and Discussion

Figure 4 shows the axial velocity ( u ) profile over the channel half-depth at a cross sectional boundary between two lateral cell columns (with the number of cylinders per lateral column = four), as the porosity is varied. The centers of circular cylinders are located at x = l , 3 l , 5 l and 7 l . The parabolic profile is computationally recovered for ϕ = 100 % (Figure 4(a)) as viscous flow between two parallel plates. Even at a very low solid fraction ( ϕ = 1 10 6 % ) (Figure 4 (b)), the presence of cylinders is seen to affect the velocity profile substantially near the middle region of the channel; while, the velocity profile retains parabolic characteristics near the plate. It should also be noted that the effects of the cylinder adjacent to the wall (with its center at x = l ) are more significant for the low porosity cases.
Figure 4. ( u ˜ = u × 10 4 [ m / s ] ) Axial velocity profile at the boundary normal to flow and between two neighboring cells: Effects of porosity. Number of cells = 4, Volume flow rate = 4 × 10 3 [ m 3 / s ] , Wall at x = 0. Profiles over channel half-depth.
Figure 4. ( u ˜ = u × 10 4 [ m / s ] ) Axial velocity profile at the boundary normal to flow and between two neighboring cells: Effects of porosity. Number of cells = 4, Volume flow rate = 4 × 10 3 [ m 3 / s ] , Wall at x = 0. Profiles over channel half-depth.
Entropy 09 00118 g004
Figure 5. ( u ˜ = u × 10 4 [ m / s ] ) Axial velocity profile at the boundary normal to flow and between two neighboring cells: Effects of number of cells. (a) ϕ = 99.99 % , (b) ϕ = 80 % . Volume flow rate = Number of cells × 10 5 [ m 3 / s ] , Wall at x = 0. Profiles over channel half-depth
Figure 5. ( u ˜ = u × 10 4 [ m / s ] ) Axial velocity profile at the boundary normal to flow and between two neighboring cells: Effects of number of cells. (a) ϕ = 99.99 % , (b) ϕ = 80 % . Volume flow rate = Number of cells × 10 5 [ m 3 / s ] , Wall at x = 0. Profiles over channel half-depth
Entropy 09 00118 g005
In Figure 5, similar to Figure 4, the velocity profiles over the half-depth are presented to show the effects of the number of cells across the channel. Two cases are shown for ϕ = 99.99 % (Figure 5(a)), and ϕ = 80.00 % (Figure 5(b)). Large velocity changes around the cylinders compared to the corresponding changes near the plate (located at x = 0 ) result in a smaller rate of entropy generation in the cell adjacent to the plate.
Table 1 lists computational results of the rate of entropy generation of each cell for the case of ten cells across the entire channel depth. Even at a very high porosity of ϕ = 99.99 % , the plate effects are limited to the region within three cells from the plate wall with the affected region becoming even smaller as the porosity is decreased.
Table 1. Variation of S ˙ G , c e l l / over Channel Half-Width.(Cell I in contact with the bounding plate at y=H in Fig 2(a))
Table 1. Variation of S ˙ G , c e l l / over Channel Half-Width.(Cell I in contact with the bounding plate at y=H in Fig 2(a))
S ˙ G , c e l l / (Cell i)/ S ˙ G , c e l l / (Cell 5) (i = 1-5)
ϕ = 85%95 %99 %99.99 %
Cell 10.6390.6470.6560.692
Cell 20.9990.9950.9810.927
Cell 31.00.9990.9990.997
Cell 41.01.01.01.0
Cell 51.01.01.01.0
Figure 6. ( H 2 / μ u m ) ( d p / d x ) vs H 2 / K .
Figure 6. ( H 2 / μ u m ) ( d p / d x ) vs H 2 / K .
Entropy 09 00118 g006
Figure 6 summarizes the computational results of the (non-dimensional) axial pressure gradient vs D a 2 , Eq.(4), covering the porosity range up to ϕ = 1 10 6 % . As was shown in Table 1 the bounding wall affects the flow up to ~ 3 unit cells away from the wall. The convergence of the non-dimensional pressure gradient to the Darcian limit is computationally confirmed, indicating that a critical value of D a for convergence depends on the porosity. Computations are terminated for a specified value of ϕ upon reaching a condition sufficiently close to the Darcian limit. On the other hand, even at the solid fraction of C = 10 6 % , the viscous effect of the flow around the cylinder remains important with the minimum value of D a 2 being limited to ~ 1.5 . (The computational lower limit is due to difficulties of the computational grid generation that is small in size and large in numbers sufficiently for accurate resolution of the velocity field near the cylinder.) The lowest value of D a 2 corresponds to the case of H / l = 1 (a single cylinder over the channel width) for each set of numerical results with a fixed value of ϕ . Also, results may not be presented in a continuous curve as an incremental change in the number of cylinders in the lateral direction leads to a step change in D a 2 . Figure 6 indicates that, between the Darcian and the viscous flow limit, all numerical results may be recovered by setting μ ^ = 1.0 1.2 in Eq.(4). Our numerical range is limited to H / l 20 . Classical Darcy’s law is valid under the assumption of very slow ( Re 0 ) flow through a layer of a porous medium in which the local (microscopic) length scale ( l in the present analysis) is sufficiently small compared to the overall (macroscopic) length scale ( H ). For the two cases of (a) ϕ = 50 % and (b) ϕ = 90 % , Figure 6 yields the following results:
(a)   ϕ = 50 % , D a 2 = ~ 5.0 × 10 6   for   H / l = 20 ; D a 2 = ~ 1.0 × 10 4   as lower threshold for Darcian limit . (b)   ϕ = 90 % , D a 2 = ~ 2.5 × 10 4 for   H / l = 20 ; D a 2 = ~ 1.0 × 10 3 as lower threshold for Darcian limit.
A corresponding thermal problem had been analyzed [2,6,16] for stability of a fluid saturated porous medium between two horizontal plates heated from below. Results, obtained under an assumption of μ e = μ ( μ ^ = 1 ), indicate that the Darcian limit is reached in terms of the critical Rayleigh number for the onset of convection if D a 2 10 3 , and that the viscous flow limit is valid if D a 2 10 1 .
Our computational results along with Figure 6 indicate that the Darcy- Brinkman equation with the viscosity ratio substantially different from unity fails to satisfy the non-slip condition at bounding walls, particularly under the high porosity condition of D a 2 < ~ 10 3 , and that the effect of the bounding walls on the flow structure, which is confined to a narrow region near the walls, may be approximated by a porous medium with μ ^ = 1 . Figure 7 is a sketch of a three layer model, proposed to accommodate the wall effects in the analyses of a Brinkman porous medium with μ ^ 1 . It consists of two layers near the bounding walls with μ ^ B (viscosity ratio of the top and the bottom layer) = 1 , and a middle (interior) layer with μ ^ I (viscosity ratio of the middle layer) 1 . A solution for a parallel flow through the three layers may be sought from the Darcy-Brinkman equation for the top ( H L y H ) as well as for the middle layer ( 0 y H L ) under the conditions of the symmetry at y = 0 , the non-slip condition at y = H , and the velocity- and the shear stress-continuity at y = H L .
The result is,
( H 2 / μ u m ) ( d p / d x ) D a 2 = 1 1 D a μ ^ I X + Y 1 + μ ^ I X Y
where X = tanh ( D a μ ^ I ( 1 L H ) ) ,         y = tanh ( D a L H )
By setting L / H = 0 and 1 in Eq.(10), Eq.(4) is recovered for a porous layer with μ ^ = μ I and with μ ^ = 1 , respectively. The left hand side of Eq.(10) is the ratio of the non-dimensional pressure gradient of the three layer model to that of a single layer (= the Darcian limit of L / H = 0 ). For a common pressure gradient, therefore, the mean velocity, μ m , of the three layer model is higher than that of the single layer. Greater the effective viscosity of the middle layer is relative to the fluid viscosity, more flow is channeled through the top (bottom) layer. The length scale of the top layer depth, L , is of the order of 6 l in Figure 2, implying that the depth ratio, L / H , depends on the characteristic length scale of the porous structure (such as l in Figure 2) as well as on the macroscopic scale of the channel depth, H. Figure 8 shows Eq.(10) as D a is varied with L / H as third parameter for the case of μ ^ I = 10 . For a case in which the wall layer thickness, L , is ~ 1 / 1000 of the channel half-depth, H , an increase of ~ 10 % in the mean velocity across the channel is predicted at D a 2 = 10 3 due to a higher flow velocity in the wall layer. Although a substantial reduction of the wall effect is observed as the magnitude of L / H is reduced from 10 3 to 10 4 , the wall effects remain important even at L / H = 10 4 for D a 2 < ~ 10 4 .
Figure 7. Schematic Diagram of Three Layer Model.
Figure 7. Schematic Diagram of Three Layer Model.
Entropy 09 00118 g007
Figure 8. ( H 2 / μ u m ) ( d p / d x ) / D a 2 vs D a 2 of the three layer model with μ ^ I = 10 .
Figure 8. ( H 2 / μ u m ) ( d p / d x ) / D a 2 vs D a 2 of the three layer model with μ ^ I = 10 .
Entropy 09 00118 g008

Summary

The effects of the bounding solid walls are examined numerically for flow through regular, square arrays of circular cylinders between two parallel plates. The lateral velocity profiles are altered substantially from the parabolic profile of the viscous flow due to sharp velocity gradients around the cylinders even for the solid fraction as low as 10 6 % . Between the two limits of the Darcian porous medium and the viscous flow, our computational results agree well with the Darcy-Brinkman equation with μ ^ = ~ 1 in terms of the axial pressure gradient, satisfying the non-slip boundary conditions at the bounding walls. This implies that, for a porous medium for which the Brinkman term is needed to account for the local geometric heterogeneity (which is absent for regular arrays of solid objects), a degree of satisfying the boundary conditions is compromised, particularly for the cases in which μ ^ is substantially greater than unity. It is proposed that the non-slip condition at the bounding solid walls be accounted for by introducing a thin porous layer with μ ^ = 1 near the solid walls.
Finally, the study indicates that the local value of the entropy generation rate is effective in distinguishing the region near and away from the solid boundary in the hydrodynamic patterns.

Nomenclature

C
solid fraction ( = 1 ϕ )
D a
H / K
f ( C )
function in Eq.(7)
H
channel half-depth
K
permeability [ m 2 ]
l
half of the side of a unit cell ( Figure 1(b))
L
depth of the top and the bottom layer in three layer model (Figure 7)
p
pressure
q
volume flow rate per channel depth
S ˙ G , c e l l /
rate of entropy generation over a unit cell per channel depth
S ˙ G / / /
rate of entropy generation per channel width
T
temperature [K]
u
x-direction velocity of viscous flow
u ¯
u s / u m
u m
mean velocity (=q/2H)
u s
superficial velocity in porous media
v
y-direction velocity of viscous flow
V
velocity vector
x
axial (flow direction, longitudinal coordinate)
y
lateral coordinate
y ˜
y / H

Greek Symbols 

μ
dynamic viscosity [ N s / m 2 ] of fluid
μ e
effective(dynamic) viscosity [ N s / m 2 ] for Brinkman term,
 
Eq.(1)
μ ^
viscosity ratio, μ e / μ
μ ^ B
viscosity ratio of the top and the bottom layer is Figure 7 (=1)
μ ^ I
viscosity ratio of the middle layer in Figure 7
ϕ
porosity of porous layer
Φ
dissipation function, Eq.(9)Main text paragraph (Apply M_Text format).

References

  1. Bejan, A. Entropy Generation Through Heat and Fluid Flow. John Wiley and Sons, 1982. [Google Scholar]
  2. Cheng, P. Heat Transfer in Geothermal Systems. Adv. Heat Trans. 1987, 14, 1–105. [Google Scholar]
  3. Durlofsky, L.; Brady, J.F. Analysis of the Brinkman equation as a model for flow in porous media. Phys. Fluids. 1987, 30, 3329–3340. [Google Scholar] [CrossRef]
  4. Forsythe, G.E.; Malcom, A.; Moler, C.B. Computer Methods for Mathematical Computations. Prentice-Hall: New Jersey, 1977. [Google Scholar]
  5. Givler, R.C.; Altobelli, S.A. A determination of the effective viscosity for the Brinkman-Forchheimer flow model. J. Fluid Mech. 1994, 258, 355–370. [Google Scholar] [CrossRef]
  6. Katto, Y.; Masuoka, T. Criterion for the onset of convective flow in a fluid in a porous medium. Int. J. Heat Mass Transfer 1967, 10, 297–309. [Google Scholar] [CrossRef]
  7. Khaled, A.R.A.; Vafai, K. The role of porous media in modeling flow and heat transfer in biological tissues. Int. J. Heat Mass Transfer 2003, 46, 4989–5003. [Google Scholar] [CrossRef]
  8. Koplik, J.; Levine, H.; Zee, A. Viscosity renormalization in the Brinkman equation. Phys. Fluids 1983, 26, 2864–2870. [Google Scholar] [CrossRef]
  9. Liu, S.; Masliyah, J.H. Non-linear flows in porous media. J. Non-Newtonian Fluid Mech. 1999, 86, 229–252. [Google Scholar] [CrossRef]
  10. Lundgren, T.S. Slow flow through stationary random beds and suspensions of spheres. J. Fluid Mech. 1972, 51, 273–299. [Google Scholar] [CrossRef]
  11. Nield, D.A. The boundary correction for the Rayleigh-Darcy problem: limitations of the Brinkman equation. J. Fluid Mech. 1983, 128, 37–46. [Google Scholar]
  12. Nield, D.A.; Bejan, A. Convection in Porous Media. Springer-Verlag New York, 1992. [Google Scholar]
  13. Pries, A.R.; Secomb, T.W.; Jacobs, H.; Sperandio, M.; Osterloh, K.; Gaehtgens, P. Microvascular blood flow resistance: role of endothelial surface layer. Am. J. Physiol. 1997, 273, H2272–H2279. [Google Scholar] [PubMed]
  14. Pries, A.R.; Secomb, T.W.; Gaehtgens, P. The endothelial surface layer. Pflugers Arch.− Eur. J. Physiol. 2000, 440, 653–666. [Google Scholar] [CrossRef]
  15. Sangani, A.S.; Acrivos, A. Slow flow past periodic arrays of cylinders with application to heat transfer. Int. J. Multiphase Flow 1982, 8, 193–206. [Google Scholar] [CrossRef]
  16. Walker, K.; Homsy, G.M. A note on convective instability in Boussinesq fluids and porous media. J. Heat Transfer 1977, 99, 338–339. [Google Scholar] [CrossRef]
  17. Weinbaum, S.; Zhang, X.; Han, Y.; Vink, H.; Cowin, S.C. Mechanotransduction and flow across the endothelial glycocalyx. PNAS 2003, 100, 7988–7995. [Google Scholar] [CrossRef] [PubMed] [Green Version]

Share and Cite

MDPI and ACS Style

Liu, H.; Patil, P.R.; Narusawa, U. On Darcy-Brinkman Equation: Viscous Flow Between Two Parallel Plates Packed with Regular Square Arrays of Cylinders. Entropy 2007, 9, 118-131. https://doi.org/10.3390/e9030118

AMA Style

Liu H, Patil PR, Narusawa U. On Darcy-Brinkman Equation: Viscous Flow Between Two Parallel Plates Packed with Regular Square Arrays of Cylinders. Entropy. 2007; 9(3):118-131. https://doi.org/10.3390/e9030118

Chicago/Turabian Style

Liu, Haidong, Prabhamani R. Patil, and Uichiro Narusawa. 2007. "On Darcy-Brinkman Equation: Viscous Flow Between Two Parallel Plates Packed with Regular Square Arrays of Cylinders" Entropy 9, no. 3: 118-131. https://doi.org/10.3390/e9030118

Article Metrics

Back to TopTop